ZHCSSQ9G october   1980  – august 2023 AM26LS32AC , AM26LS32AM , AM26LS33AM

PRODUCTION DATA  

  1.   1
  2. 特性
  3. 应用
  4. 说明
  5. Revision History
  6. Pin Configuration and Functions
  7. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Dissipation Ratings
    8. 6.8 Typical Characteristics
  8. Parameter Measurement Information
    1.     17
  9. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
    4. 8.4 Device Functional Modes
      1.      23
  10. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curve
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 接收文档更新通知
    2. 10.2 支持资源
    3. 10.3 Trademarks
    4. 10.4 静电放电警告
    5. 10.5 术语表
  12. 11Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Electrical Characteristics

over recommended ranges of VCC, VIC, and operating free-air temperature (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP(1) MAX UNIT
VIT+ Positive-going input threshold voltage VO = VOHmin, IOH = –440 µA AM26LS32A 0.2 V
AM26LS33A 0.5
VIT– Negative-going input threshold voltage VO = 0.45 V , IOL = 8 mA AM26LS32A –0.2(2) V
AM26LS33A –0.5(2)
Vhys Hysteresis voltage
(VIT+ – VIT–)
50 mV
VIK Enable-input clamp voltage VCC = MIN, II = –18 mA –1.5 V
VOH High-level output voltage VCC = MIN, VID = 1 V,
VI(G) = 0.8 V, IOH = –440 µA
AM26LS32AC, AM26LS33AC 2.7 V
AM26LS32AM, AM26LS32AI, AM26LS33AM 2.5
VOL Low-level output voltage VCC = MIN, VID = –1 V,
VI(G) = 0.8 V
IOL= 4 mA 0.4 V
IOL= 8 mA 0.45
IOZ Off-state (high-impedance state) output current VCC = MAX VO = 2.4 V 20 µA
VO = 0.4 V –20
II Line input current VI = 15 V, other input at –10 V to 15 V 1.2 mA
VI = –15 V, other input at –15 V to 10 V –1.7
II(EN) Enable input current VI = 5.5 V 100 µA
IH High-level enable current VI = 2.7 V 20 µA
IL Low-level enable current VI = 0.4 V –0.36 mA
ri Input resistance VIC = –15 V to 15 V, one input to ac ground 12 15
IOS Short-circuit output current(3) VCC = MAX –15 –85 mA
ICC Supply current VCC = MAX, all outputs disabled 52 70 mA
All typical values are at VCC = 5 V, TA = 25°C, and VIC = 0.
The algebraic convention, in which the less positive (more negative) limit is designated as minimum, is used in this data sheet for threshold levels only.
Not more than one output must be shorted to ground at a time, and duration of the short circuit must not exceed one second.