首頁 交換器與多工器 類比交換器與多工器 通訊協定與匯流排開關與多工器
首頁
交換器與多工器
類比交換器與多工器
通訊協定與匯流排開關與多工器

TS3V330

現行

3.3-V、2:1 (SPDT)、4 通道視訊交換器

立即訂購
產品規格表

TS3V330

現行
立即訂購

產品詳細資料

Protocols Composite, RGB Configuration 2:1 SPDT Number of channels 4 Bandwidth (MHz) 300 Ron (typ) (mΩ) 5000 Input/output voltage (min) (V) 0 Input/output voltage (max) (V) 3.6 Supply current (typ) (µA) 10 ESD HBM (typ) (kV) 2 Operating temperature range (°C) -40 to 85 Crosstalk (dB) -80 ESD CDM (kV) 1 Input/output continuous current (max) (mA) 128 COFF (typ) (pF) 10 CON (typ) (pF) 17 Off isolation (typ) (dB) -50 OFF-state leakage current (max) (µA) 1 Propagation delay time (µs) 0.0025 Ron (max) (mΩ) 10000 Turnoff time (disable) (max) (ns) 3.5 Turnon time (enable) (max) (ns) 6.5 VIH (min) (V) 2 VIL (max) (V) 0.8 Rating Catalog
Protocols Composite, RGB Configuration 2:1 SPDT Number of channels 4 Bandwidth (MHz) 300 Ron (typ) (mΩ) 5000 Input/output voltage (min) (V) 0 Input/output voltage (max) (V) 3.6 Supply current (typ) (µA) 10 ESD HBM (typ) (kV) 2 Operating temperature range (°C) -40 to 85 Crosstalk (dB) -80 ESD CDM (kV) 1 Input/output continuous current (max) (mA) 128 COFF (typ) (pF) 10 CON (typ) (pF) 17 Off isolation (typ) (dB) -50 OFF-state leakage current (max) (µA) 1 Propagation delay time (µs) 0.0025 Ron (max) (mΩ) 10000 Turnoff time (disable) (max) (ns) 3.5 Turnon time (enable) (max) (ns) 6.5 VIH (min) (V) 2 VIL (max) (V) 0.8 Rating Catalog
TVSOP (DGV) 16 23.04 mm² (3.6 mm × 6.4 mm) SOIC (D) 16 59.4 mm² (9.9 mm × 6 mm) SSOP (DBQ) 16 29.4 mm² (4.9 mm × 6 mm) VQFN (RGY) 16 14 mm² (4 mm × 3.5 mm) TSSOP (PW) 16 32 mm² (5 mm × 6.4 mm)
  • Low Differential Gain and Phase (DG = 0.82%, DP = 0.1 Degree Typ)
  • Wide Bandwidth (BW = 300 MHz Min)
  • Low Crosstalk (XTALK = -80 dB Typ)
  • Low Power Consumption (ICC = 10 µA Max)
  • Bidirectional Data Flow With Near-Zero Propagation Delay
  • Low ON-State Resistance (ron = 3 Typ)
  • Rail-to-Rail Switching on Data I/O Ports (0 to VCC)
  • VCC Operating Range From 3 V to 3.6 V
  • Ioff Supports Partial-Power-Down Mode Operation
  • Data and Control Inputs Provide Undershoot Clamp Diode
  • Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
  • ESD Performance Tested Per JESD 22
    • 2000-V Human-Body Model (A114-B, Class II)
    • 1000-V Charged-Device Model (C101)
  • Suitable for Both RGB and Composite-Video Switching
  • Low Differential Gain and Phase (DG = 0.82%, DP = 0.1 Degree Typ)
  • Wide Bandwidth (BW = 300 MHz Min)
  • Low Crosstalk (XTALK = -80 dB Typ)
  • Low Power Consumption (ICC = 10 µA Max)
  • Bidirectional Data Flow With Near-Zero Propagation Delay
  • Low ON-State Resistance (ron = 3 Typ)
  • Rail-to-Rail Switching on Data I/O Ports (0 to VCC)
  • VCC Operating Range From 3 V to 3.6 V
  • Ioff Supports Partial-Power-Down Mode Operation
  • Data and Control Inputs Provide Undershoot Clamp Diode
  • Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
  • ESD Performance Tested Per JESD 22
    • 2000-V Human-Body Model (A114-B, Class II)
    • 1000-V Charged-Device Model (C101)
  • Suitable for Both RGB and Composite-Video Switching

The TS3V330 video switch is a 4-bit 1-of-2 multiplexer/demultiplexer, with a single switch-enable (EN) input. When EN is low, the switch is enabled and the D port is connected to the S port. When EN is high, the switch is disabled and the high-impedance state exists between the D and S ports. The select (IN) input controls the data path of the multiplexer/demultiplexer.

Low differential gain and phase make this switch ideal for composite and RGB video applications. This device has wide bandwidth and low crosstalk, making it suitable for high-frequency applications as well.

This device is fully specified for partial-power-down applications using Ioff. The Ioff feature ensures that damaging current will not backflow through the device when it is powered down. This switch maintains isolation during power off.

To ensure the high-impedance state during power up or power down, EN should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

The TS3V330 video switch is a 4-bit 1-of-2 multiplexer/demultiplexer, with a single switch-enable (EN) input. When EN is low, the switch is enabled and the D port is connected to the S port. When EN is high, the switch is disabled and the high-impedance state exists between the D and S ports. The select (IN) input controls the data path of the multiplexer/demultiplexer.

Low differential gain and phase make this switch ideal for composite and RGB video applications. This device has wide bandwidth and low crosstalk, making it suitable for high-frequency applications as well.

This device is fully specified for partial-power-down applications using Ioff. The Ioff feature ensures that damaging current will not backflow through the device when it is powered down. This switch maintains isolation during power off.

To ensure the high-impedance state during power up or power down, EN should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
filter 尋找其它 通訊協定與匯流排開關與多工器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
針腳對針腳的功能與所比較的裝置相同。
SN74CBTLV3257 現行 具有部分斷電模式的 3.3-V、2:1 (SPDT)、4 通道類比開關 Supports additional I2C, I2S, JTAG, RGMII, SPI, TDM, UART Protocols

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 1
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 TS3V330 datasheet (Rev. C) 2005/7/11

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

介面轉接器

LEADED-ADAPTER1 — 適用於快速測試 TI 的 5、8、10、16 及 24 針腳引線封裝的表面貼裝至 DIP 接頭適配器

EVM-LEADED1 板可用於快速測試和搭建 TI 常見的有引腳封裝  此電路板具備板上配置，可將 TI 的 D、DBQ、DCT、DCU、DDF、DGS、DGV 和 PW 表面黏著封裝轉換為 100mil DIP 排針。     

使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
介面轉接器

LEADLESS-ADAPTER1 — 用於測試 TI 的 6、8、10、12、14、16 和 20 針腳無引線封裝的表面貼裝至 DIP 接頭適配器

EVM-LEADLESS1 電路板允許快速測試和麵包板搭建 TI 常見的無引腳封裝。  此電路板具有封裝設計，可將 TI 的 DRC、DTP、DQE、RBW、RGY、RSE、RSV、RSW、RTE、RTJ、RUK、RUC、RUG、RUM、RUT 和 YZP 表面黏著封裝轉換為 100mil DIP 接頭。
使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
參考設計

TIDA-00232 — 無線低音喇叭放大器參考設計

此無線重低音喇叭放大器參考設計展示了可輕鬆將無線連線整合至傳統類比輸入重低音喇叭設計的方式。有線或無線模式由 MSP430 控制。參考設計包括具有用於監控與控制之軟體的高性能立體聲數位音訊放大器系統。此設計採用 CC8520 PurePath 音訊無線 RF SoC 模組，適用於無線模式下的音訊串流。提供參考設計中使用的電路板與 EVM 的電路圖、物料清單和設計考量。

支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
TVSOP (DGV) 16 Ultra Librarian
SOIC (D) 16 Ultra Librarian
SSOP (DBQ) 16 Ultra Librarian
VQFN (RGY) 16 Ultra Librarian
TSSOP (PW) 16 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片