首頁 電源管理 多通道 IC (PMIC)
首頁
電源管理
多通道 IC (PMIC)

TPS65084

現行

適用 Braswell 處理器的可編程中輸入電壓範圍電源管理 IC (PMIC)

立即訂購
產品規格表

TPS65084

現行
產品規格表 立即訂購

產品詳細資料

Processor supplier Intel/Altera Processor name Braswell Product type Processor and FPGA Regulated outputs (#) 13 Step-down DC/DC converter 3 Step-up DC/DC converter 0 LDO 4 Vin (min) (V) 5.6 Vin (max) (V) 21 Vout (min) (V) -0.3 Vout (max) (V) 3.575 Iout (max) (A) 11 Configurability Factory programmable, Software configurable Features Comm control, Dynamic voltage scaling, Enable, Enable pin, I2C control, Overcurrent protection, Power good, Power sequencing, Synchronous rectification, Thermal shutdown, UVLO fixed Rating Catalog Operating temperature range (°C) -40 to 85 Step-down DC/DC controller 3 Step-up DC/DC controller 0 Iq (typ) (mA) 0.3 Switching frequency (max) (kHz) 3100 Shutdown current (ISD) (typ) (µA) 65 Switching frequency (typ) (kHz) 2500
Processor supplier Intel/Altera Processor name Braswell Product type Processor and FPGA Regulated outputs (#) 13 Step-down DC/DC converter 3 Step-up DC/DC converter 0 LDO 4 Vin (min) (V) 5.6 Vin (max) (V) 21 Vout (min) (V) -0.3 Vout (max) (V) 3.575 Iout (max) (A) 11 Configurability Factory programmable, Software configurable Features Comm control, Dynamic voltage scaling, Enable, Enable pin, I2C control, Overcurrent protection, Power good, Power sequencing, Synchronous rectification, Thermal shutdown, UVLO fixed Rating Catalog Operating temperature range (°C) -40 to 85 Step-down DC/DC controller 3 Step-up DC/DC controller 0 Iq (typ) (mA) 0.3 Switching frequency (max) (kHz) 3100 Shutdown current (ISD) (typ) (µA) 65 Switching frequency (typ) (kHz) 2500
VQFN (RSK) 64 64 mm² 8 x 8
  • Three Variable-Output Voltage Step-Down
    Controllers
    • Wide VIN Range From 5.4 V to 21 V
    • Up to 7-A Output Current for BUCK1 (VCC) and
      BUCK6 (VDDQ), and 11-A for BUCK2 (VGG)
      Using External FETs
    • I2C DVS Control (0.5 V to 1.45 V in 10-mV
      Steps) for BUCK1 and BUCK2
    • Pin-Selectable Output Voltages (1.2 V or
      1.35 V) for BUCK6 (VDDQ)
  • Three Variable-Output Voltage Synchronous Step-
    Down Converters
    • VIN Range From 4.5 V to 5.5 V
    • Up to 3.5 A of Output Current for BUCK3 (VNN)
      With I2C DVS Control (0.65 V to
      1.45 V in 25-mV Steps)
    • Up to 3 A of Output Current for BUCK4
      (V1P05A) and up to 1.5 A of Output Current for
      BUCK5 (V1P8A)
  • Three LDO Regulators With Adjustable Output
    Voltage
    • LDOA1: I2C-Selectable Output Voltage From
      1.35 V to 3.3 V for up to 200 mA of Output Current
    • LDOA2: I2C-Selectable Output Voltage From
      1.05 V, 1.1 V, 1.15 V, and 1.2 V
    • LDOA3: I2C-Selectable Output Voltage From
      1.1 V, 1.15 V, 1.2 V, and 1.24 V
  • VTT LDO for DDR3 and DDR4 Memory
    Termination
  • Three Load Switches With Slew Rate Control
    • Up to 300 mA of Output Current With Voltage
      Drop Less Than 1.5% of Nominal Input Voltage
    • RDSON < 96 mΩ at Input Voltage of 1.8 V
  • I2C Interface (Device Address 0x5E) Supports
    Standard Mode (100 kHz), Fast Mode (400 kHz),
    and Fast Mode Plus (1 MHz)
  • 64-Pin, Single-Row, 0.4-mm Pitch QFN Package
  • Three Variable-Output Voltage Step-Down
    Controllers
    • Wide VIN Range From 5.4 V to 21 V
    • Up to 7-A Output Current for BUCK1 (VCC) and
      BUCK6 (VDDQ), and 11-A for BUCK2 (VGG)
      Using External FETs
    • I2C DVS Control (0.5 V to 1.45 V in 10-mV
      Steps) for BUCK1 and BUCK2
    • Pin-Selectable Output Voltages (1.2 V or
      1.35 V) for BUCK6 (VDDQ)
  • Three Variable-Output Voltage Synchronous Step-
    Down Converters
    • VIN Range From 4.5 V to 5.5 V
    • Up to 3.5 A of Output Current for BUCK3 (VNN)
      With I2C DVS Control (0.65 V to
      1.45 V in 25-mV Steps)
    • Up to 3 A of Output Current for BUCK4
      (V1P05A) and up to 1.5 A of Output Current for
      BUCK5 (V1P8A)
  • Three LDO Regulators With Adjustable Output
    Voltage
    • LDOA1: I2C-Selectable Output Voltage From
      1.35 V to 3.3 V for up to 200 mA of Output Current
    • LDOA2: I2C-Selectable Output Voltage From
      1.05 V, 1.1 V, 1.15 V, and 1.2 V
    • LDOA3: I2C-Selectable Output Voltage From
      1.1 V, 1.15 V, 1.2 V, and 1.24 V
  • VTT LDO for DDR3 and DDR4 Memory
    Termination
  • Three Load Switches With Slew Rate Control
    • Up to 300 mA of Output Current With Voltage
      Drop Less Than 1.5% of Nominal Input Voltage
    • RDSON < 96 mΩ at Input Voltage of 1.8 V
  • I2C Interface (Device Address 0x5E) Supports
    Standard Mode (100 kHz), Fast Mode (400 kHz),
    and Fast Mode Plus (1 MHz)
  • 64-Pin, Single-Row, 0.4-mm Pitch QFN Package

The TPS650842 device is a single-chip solution, power-management IC designed specifically for the latest Intel™ processors targeted for tablets, ultrabooks, and notebooks with NVDC or non-NVDC power architectures, using 2S, 3S, or 4S Li-Ion battery packs. The TPS650842 device is used for essential systems with low-voltage rails merged for the smallest footprint and lowest-cost system-power solution. The TPS650842 device provides the complete power solution based on the Intel Reference Designs. Six highly efficient step-down voltage regulators (VRs), a sink or source LDO (VTT), two LDOs, and three load switches are controlled by power-up sequence logic to provide the proper power rails, sequencing, and protection—including DDR3 and DDR4 memory power. The three regulators (BUCK1–BUCK3) support dynamic voltage scaling (DVS) for maximum efficiency—including support for Connected Standby. The high-frequency VRs use small inductors and capacitors to achieve a small solution size. An I2C interface allows simple control by an embedded controller (EC) or by a system on chip (SoC). The PMIC comes in an 8-mm × 8-mm single-row QFN package with a thermal pad for good thermal dissipation and ease of board routing.

Use the following email address to request the full version of this data sheet: ipgmkt@list.ti.com.

The TPS650842 device is a single-chip solution, power-management IC designed specifically for the latest Intel™ processors targeted for tablets, ultrabooks, and notebooks with NVDC or non-NVDC power architectures, using 2S, 3S, or 4S Li-Ion battery packs. The TPS650842 device is used for essential systems with low-voltage rails merged for the smallest footprint and lowest-cost system-power solution. The TPS650842 device provides the complete power solution based on the Intel Reference Designs. Six highly efficient step-down voltage regulators (VRs), a sink or source LDO (VTT), two LDOs, and three load switches are controlled by power-up sequence logic to provide the proper power rails, sequencing, and protection—including DDR3 and DDR4 memory power. The three regulators (BUCK1–BUCK3) support dynamic voltage scaling (DVS) for maximum efficiency—including support for Connected Standby. The high-frequency VRs use small inductors and capacitors to achieve a small solution size. An I2C interface allows simple control by an embedded controller (EC) or by a system on chip (SoC). The PMIC comes in an 8-mm × 8-mm single-row QFN package with a thermal pad for good thermal dissipation and ease of board routing.

Use the following email address to request the full version of this data sheet: ipgmkt@list.ti.com.
filter 尋找其它 多通道 IC (PMIC)
下載 觀看有字幕稿的影片 影片
更多資訊和樣品供貨情況

提供完整產品規格表和其他資訊。立即索取

[RSK] 封裝用於樣品 (TPS650842A0RSKT)。立即索取

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 3
重要文件 類型 標題 格式選項 日期
* Data sheet TPS650842 PMIC for Intel™ Braswell Platform datasheet PDF | HTML 2015年 9月 1日
User guide TPS65084x Design Guide 2015年 8月 29日
Application note TPS65084x Schematic Checklist, Layout Checklist, and ILIM Calculator Tool 2015年 8月 26日

設計與開發

電源供應解決方案

探索包括 TPS65084 的解決方案。TI 提供適用於 TI 與非 TI 之系統單晶片 (SoC)、處理器、微控制器、感測器或現場可編程邏輯閘陣列 (FPGA) 的電源供應解決方案。

檢視解決方案
開發模組 (EVM) 的 GUI

IPG-UI — IPG-UI EVM GUI (Windows Installer)

The IPG-UI GUI can be used to configure multiple PMIC devices to evaluate the features and performance of those devices.  This GUI is built using web-based technologies and supports interacting with the EVM hardware using a USB2ANY adapter board. The USB2ANY Explorer is provided to allow (...)

支援產品和硬體

支援產品和硬體
下載
開發模組 (EVM) 的 GUI

IPG-UI-LINUX — IPG-UI EVM GUI (Linux Installer)

The IPG-UI GUI can be used to configure multiple PMIC devices to evaluate the features and performance of those devices.  This GUI is built using web-based technologies and supports interacting with the EVM hardware using a USB2ANY adapter board. The USB2ANY Explorer is provided to allow (...)

支援產品和硬體

支援產品和硬體
下載
開發模組 (EVM) 的 GUI

IPG-UI-OSX — IPG-UI EVM GUI (OSX Installer)

The IPG-UI GUI can be used to configure multiple PMIC devices to evaluate the features and performance of those devices.  This GUI is built using web-based technologies and supports interacting with the EVM hardware using a USB2ANY adapter board. The USB2ANY Explorer is provided to allow (...)

支援產品和硬體

支援產品和硬體
下載
開發模組 (EVM) 的 GUI

TPS65084X-GUI — TPS65084X device supporting file for IPG-UI

The user must first download IPG-UI before using this device supporting file for TPS65084X.
支援產品和硬體

支援產品和硬體
下載
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VQFN (RSK) 64 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片