現在提供此產品的更新版本
功能相同,但針腳輸出與所比較的裝置不同。
TPS4H160-Q1
- Qualified for automotive applications
- AEC-Q100 qualified with the following results:
- Device temperature grade 1: –40°C to 125°C ambient operating temperature range
- Device HBM ESD classification level H3A
- Device CDM ESD classification level C4B
- Functional Safety-Capable
- Quad-channel 160mΩ smart high-side switch with
full diagnostics
- Version A: open-drain digital output
- Version B: current-sense analog output
- Wide operating voltage 3.4V to 40V
- Ultra-low standby current: <500nA
- High-accuracy current sense: ±15% under >25mA load
- Adjustable current limit with external resistor, ±15% under >500mA load
- Protection
- Short-to-GND protection by current limit (internal or external)
- Thermal shutdown with latch off option and thermal swing
- Inductive load negative voltage clamp with optimized slew rate
- Loss-of-GND and loss-of-battery protection
- Diagnostics
- Overcurrent and short-to-ground detection
- Open-load and short-to-battery detection
- Global fault report for fast interrupt
- 28-pin thermally-enhanced PWP package
The TPS4H160-Q1 device is fully protected quad-channel smart high-side switch with four integrated 160mΩ NMOS power FETs.
Full diagnostics and high-accuracy current sense enable intelligent control of the load.
An external adjustable current limit improves the reliability of whole system by limiting the inrush or overload current.
您可能會感興趣的類似產品
功能相同,但針腳輸出與所比較的裝置不同。
技術文件
設計與開發
如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。
TPS4H160EVM — TPS4H160-Q1 四通道智慧型高壓側電源開關參考設計
TPS4H160A-Q1 Unencrypted PSpice Transient Model Package (Rev. A)
TPS4H160B-Q1 Unencrypted PSpice Transient Model Package (Rev. A)
TIDA-010016 — 8 埠 IO-Link 主站參考設計
TIDA-010253 — 適用於儲能系統的電池控制單元參考設計
此參考設計為高電壓鋰離子 (Li-ion)、磷酸鐵鋰 (LiFePO4) 電池架的中央控制器。此設計提供適用於高電壓繼電器的驅動電路、通訊介面 (包括 RS-485、控制器區域網路 (CAN)、菊鍊與乙太網路)、濕度感測器的可擴充介面、高電壓類比轉數位轉換器 (ADC),以及電流感測器。
此設計使用高性能微控制器進行開發和測試應用。這些功能讓此參考設計適用於高容量電池架應用的中央控制器。
TIDA-01323 — 具有四路 4-Gbps FPD-Link III、雙 CSI -2 輸出和 PoC 的 ADAS 多感測器集線器參考設計
TIDA-020071 — TDA4 四路車用 PHY RGMII 參考設計
此參考設計透過 RGMII 乙太網路擴充連接器介接 Jacinto™ 7 處理器 EVM 板。藉由 TI 汽車乙太網路實體層 (PHY) 新增四個汽車乙太網路。設計採用 TI 的 DP83TC818S-Q1 100Mbps/s 與 DP83TG721S-Q1 1000Mbps 單對乙太網路 (SPE) PHY。使用耦合網路,以 12V 耦合至數據線。
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| HTSSOP (PWP) | 28 | Ultra Librarian |
訂購與品質
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。