首頁 音訊、觸覺和壓電 音訊放大器 喇叭、電視與條型音箱音訊放大器
首頁
音訊、觸覺和壓電
音訊放大器
喇叭、電視與條型音箱音訊放大器

TAS5751M

現行

具有 EQ & AGL 的 25-W 立體聲道、40-W 單聲道、8 至 26.4-V、數位輸入開迴路 D 類音訊放大器

立即訂購
產品規格表

TAS5751M

現行
產品規格表 立即訂購

產品詳細資料

Audio input type Digital Input Architecture Class-D Speaker channels (max) Stereo Control interface Software Output power (W) 25 Power stage supply (max) (V) 26.4 Power stage supply (min) (V) 8 RDS(on) (Ω) 0.08 THD + N at 1 kHz (%) 0.03 Load (min) (Ω) 4 Analog supply voltage (min) (V) 3 Analog supply voltage (max) (V) 3.6 Rating Catalog Operating temperature range (°C) 0 to 85
Audio input type Digital Input Architecture Class-D Speaker channels (max) Stereo Control interface Software Output power (W) 25 Power stage supply (max) (V) 26.4 Power stage supply (min) (V) 8 RDS(on) (Ω) 0.08 THD + N at 1 kHz (%) 0.03 Load (min) (Ω) 4 Analog supply voltage (min) (V) 3 Analog supply voltage (max) (V) 3.6 Rating Catalog Operating temperature range (°C) 0 to 85
HTSSOP (DCA) 48 101.25 mm² 12.5 x 8.1
  • Audio Input/Output
    • One-Stereo Serial Audio Input
    • Supports 44.1-kHz and 48-kHz Sample Rates (LJ/RJ/I²S)
    • Supports 3-Wire I²S Mode (no MCLK required)
    • Automatic Audio Port Rate Detection
    • Supports BTL and PBTL Configuration
    • POUT = 25 W at 10% THD+N
      • PVDD = 20 V, 8 Ω, 1 kHz
  • Audio/PWM Processing
    • Independent Channel Volume Controls With Gain of 24 dB to Mute in 0.125-dB Steps
    • Programmable Three-Band Automatic Gain Limiting (AGL)
    • 20 Programmable Biquads for Speaker EQ and Other Audio-Processing Features
  • General Features
    • 106-dB SNR, A-Weighted, Referenced to Full Scale (0 dB)
    • I²C Serial Control Interface w/ two Addresses
    • Thermal, Short-Circuit, and Undervoltage Protection
    • Up to 90% Efficient
    • AD, BD, and Ternary Modulation
    • PWM Level Meter
  • Audio Input/Output
    • One-Stereo Serial Audio Input
    • Supports 44.1-kHz and 48-kHz Sample Rates (LJ/RJ/I²S)
    • Supports 3-Wire I²S Mode (no MCLK required)
    • Automatic Audio Port Rate Detection
    • Supports BTL and PBTL Configuration
    • POUT = 25 W at 10% THD+N
      • PVDD = 20 V, 8 Ω, 1 kHz
  • Audio/PWM Processing
    • Independent Channel Volume Controls With Gain of 24 dB to Mute in 0.125-dB Steps
    • Programmable Three-Band Automatic Gain Limiting (AGL)
    • 20 Programmable Biquads for Speaker EQ and Other Audio-Processing Features
  • General Features
    • 106-dB SNR, A-Weighted, Referenced to Full Scale (0 dB)
    • I²C Serial Control Interface w/ two Addresses
    • Thermal, Short-Circuit, and Undervoltage Protection
    • Up to 90% Efficient
    • AD, BD, and Ternary Modulation
    • PWM Level Meter

The TAS5751M device is an efficient, digital-input audio amplifier for driving stereo speakers configured as a bridge tied load (BTL). In parallel bridge tied load (PBTL) in can produce higher power by driving the parallel outputs into a single lower impedance load. One serial data input allows processing of up to two discrete audio channels and seamless integration to most digital audio processors and MPEG decoders. The device accepts a wide range of input data and data rates. A fully programmable data path routes these channels to the internal speaker drivers.

The TAS5751M device is a slave-only device receiving all clocks from external sources. The TAS5751M device operates with a PWM carrier between a 384-kHz switching rate and a 288-kHz switching rate, depending on the input sample rate. Oversampling combined with a fourth-order noise shaper provides a flat noise floor and excellent dynamic range from 20 Hz to 20 kHz.

The TAS5751M device is an efficient, digital-input audio amplifier for driving stereo speakers configured as a bridge tied load (BTL). In parallel bridge tied load (PBTL) in can produce higher power by driving the parallel outputs into a single lower impedance load. One serial data input allows processing of up to two discrete audio channels and seamless integration to most digital audio processors and MPEG decoders. The device accepts a wide range of input data and data rates. A fully programmable data path routes these channels to the internal speaker drivers.

The TAS5751M device is a slave-only device receiving all clocks from external sources. The TAS5751M device operates with a PWM carrier between a 384-kHz switching rate and a 288-kHz switching rate, depending on the input sample rate. Oversampling combined with a fourth-order noise shaper provides a flat noise floor and excellent dynamic range from 20 Hz to 20 kHz.

filter 尋找其它 喇叭、電視與條型音箱音訊放大器
下載 觀看有字幕稿的影片 影片

索取更多資訊

提供 PurePath™ Console 3、TAS5751M GUI 和其他設計資源。立即索取

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 2
重要文件 類型 標題 格式選項 日期
* Data sheet TAS5751M - Digital Input Audio Power Amplifier with EQ and 3-Band AGL datasheet (Rev. B) PDF | HTML 2018年 5月 15日
More literature TAS5751MEVM Quick Start Guide (Rev. A) 2016年 7月 20日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

PUREPATH-CMBEVM — 適用於音訊系統設計和開發的 PurePath™ Console 主機板

The PurePath™ Console Motherboard (PurePath-CMBEVM) provides a seamless interface between Ti’s latest PurePath Console GUI to supported TI’s digital and mixed-signal audio evaluation modules, including audio amplifiers and audio converters.

The PurePath-CMBEVM is shipped as a stand-alone board. It (...)

TI.com 無法提供
開發板

TAS5751MEVM — TAS5751M 數位輸入、開迴路 D 類音訊放大器評估模組

TAS5751MEVM 可用於評估德州儀器的 TAS5751M，這是一款 I2S 輸入的開環式功率放大器。此評估模組上配有兩個 TAS5751M 裝置，一個設定為雙聲道運作，另一個設定為單聲道運作。TAS5751M 結合一個 PWM 處理器與開環式 D 類音訊功率放大器。TAS5751MEVM 透過單一 8V 至 26.4V 的電源供電運作。TAS5751MEVM 結合 PurePath™ Console 主機板（PurePath-CMBEVM — 需另行訂購）與 PurePath™ Console GUI（PurePathConsole — (...)

使用指南: PDF
TI.com 無法提供
應用軟體及架構

PUREPATHCONSOLE — PurePath™ Console graphical development suite for audio system design and development

PurePath™ Console is a highly integrated and easy-to-use audio development suite designed specifically to simplify the evaluation, configuration and debug process associated with the development of audio products. Watch how easy it is to use the PurePath™ Console 3 software.

PurePath Console’s (...)
支援產品和硬體

支援產品和硬體
要求
支援軟體

TAS5751M-TAS5733L-SW — TAS5751M and TAS5733L GUI and software for PurePath™ Console 3

TAS5751M and TAS5733L GUI and software for PurePath™ Console 3
支援產品和硬體

支援產品和硬體
要求
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI 是有助於評估類比電路功能的設計和模擬環境。這款全功能設計和模擬套件使用 Cadence® 的類比分析引擎。PSpice for TI 包括業界最大的模型庫之一，涵蓋我們的類比和電源產品組合，以及特定類比行為模型，且使用無需支付費用。

PSpice for TI 設計和模擬環境可讓您使用其內建函式庫來模擬複雜的混合訊號設計。在進行佈局和製造之前，建立完整的終端設備設計和解決方案原型，進而縮短上市時間並降低開發成本。 

在 PSpice for TI 設計與模擬工具中，您可以搜尋 TI (...)
要求
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HTSSOP (DCA) 48 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片