SN6507-Q1
SN6507-Q1 has an internal oscillator to set the switching frequency of the power stage. As the two power switches are out of phase, the oscillator frequency is twice of the actual switching frequency of each power switch. The duty cycle is fixed with 70 ns deadtime to avoid shoot-through. The duty cycle is changeable if duty cycle feature is enabled. Please refer to Section 8.3.3.
SN6507-Q1 has a wide switching frequency range from 100 kHz up to 2 MHz, which is pin-programmable through a resistor (RCLK) to GND. Below table lists the value of RCLK to achieve certain operating frequencies (fSW). The choice of switching frequency is a trade-off between power efficiency and size of capacitive and inductive components. For example, when operating at higher switching frequency, the size of the transformer and inductor is reduced, resulting in a smaller design footprint and lower cost. However, higher frequency increases switching losses and consequently degrades the overall power supply efficiency.
Figure 8-6 can also be used to estimate the programmable switching frequency, fSW, using an external resistor value, RCLK, where RCLK is in kΩ and fSW is in kHz:
If CLK pin is shorted to GND, the part switches at its default frequency, FSW. CLK pin floating is not a valid state of operation and will cause the part to stop switching until an external clock signal is present.
The SN6507 -Q1 is a high voltage, high frequency push-pull transformer driver providing isolated power in a small solution size. The device comes with the push-pull topology’s benefits of simplicity, low EMI, and flux cancellation to prevent transformer saturation. Further space savings are achieved through duty-cycle control, which reduces component count for wide-input ranges, and by selecting a high switching frequency, reducing the size of the transformer.
The device integrates a controller and two 0.5-A NMOS power switches that switch out of phase. Its input operating range is programmed with precision undervoltage lockouts. The device is protected from fault conditions by over-current protection (OCP), adjustable under-voltage lockout (UVLO), over voltage lockout (OVLO), thermal shutdown (TSD), and break-before-make circuitry.
The programmable Soft Start (SS) minimizes inrush currents and provides power supply sequencing for critical power up requirements. Spread Spectrum Clocking (SSC) and pin-configurable Slew Rate Control (SRC) further reduces radiated and conducted emissions for ultra-low EMI requirements.
The SN6507 -Q1 is available in a 10-pin HVSSOP DGQ package. The device operation is characterized for a temperature range from –55°C to 125°C.
您可能會感興趣的類似產品
功能相同，但針腳輸出與所比較的裝置不同。
技術文件
| 重要文件 | 類型 | 標題 | 格式選項 | 下載最新的英文版本 | 日期 | |
|---|---|---|---|---|---|---|
| * | 資料表 | SN6507-Q1 Low-Emissions, 36-V Push-Pull Transformer Driver with Duty Cyle Control for Isolated Power Supplies datasheet | PDF | HTML | 2021/2/15 | ||
| Application brief | Optimized Excitation Power Stage for Electrically Excited Synchronous Machines (Rev. A) | PDF | HTML | 2026/5/5 | |||
| 白皮書 | Isolated Bias Power Supply Architecture for HEV/EV Single Stage Onboard Chargers | PDF | HTML | 2026/1/7 | |||
| 技術文章 | How isolated bias transformer parasitic capacitance impacts EMI performance | PDF | HTML | 2025/9/22 | |||
| 白皮書 | Isolated Bias Power Supply Architecture for HEV/EV HVLV DCDC Converters | PDF | HTML | 2025/1/16 | |||
| 白皮書 | Isolated Bias Power Supply Architecture for HEV and EV Onboard Chargers | PDF | HTML | 2024/11/27 | |||
| 功能安全資訊 | SN6507-Q1 Functional Safety FIT Rate, FMD and Pin FMA | PDF | HTML | 2022/5/16 | |||
| 應用說明 | How to Reduce Emissions in Push-Pull Isolated Power Supplies (Rev. A) | PDF | HTML | 2021/10/5 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
SN6507DGQEVM — 適用於低放射、500-mA 推挽式隔離電源供應器的 SN6507 評估模組
SN6507DGQEVM 允許使用者在隔離電源供應器應用中評估 SN6507 推挽式隔離變壓器驅動器的性能和功能。
PMP31182 — 採用四種不同拓撲的隔離式偏壓電源供應器參考設計
本參考設計展示四個使用不同拓撲做為 PSR 返馳、推拉式、LLC 共振和隔離式 DCDC 模組的隔離式偏壓電源供應器設計。這些拓撲可提供特定優點，但同時需有所取捨。使用四種硬體設計即可對這些拓撲進行充分比較，同時讓電力參數盡可能保持雷同。這些設計的輸入與輸出電壓為 15V，最大負載電流為 100mA。
PMP41078 — 具有 GaN HEMT 的高電壓至低電壓 DC-DC 轉換器參考設計
此參考設計描述了一款具有 650V 氮化鎵 (GaN) 高電子移動率電晶體 (HEMT) 的 3.5kW 高電壓至低電壓 DC-DC 轉換器。使用 LMG3522R030 作為一次側開關可使轉換器在高切換頻率下工作。在此設計中，轉換器使用較小尺寸的變壓器。為了緩解主動箝位金屬氧化物半導體場效應電晶體 (MOSFET) 的熱性能，該轉換器使用雙通道主動箝位電路。
PMP41139 — 3.5kW、800V 至 14V DC/DC 轉換器參考設計
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| HVSSOP (DGQ) | 10 | Ultra Librarian |
訂購與品質
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。