SN74LVC2T45
- Fully configurable dual-rail design allows each port to operate over the full 1.65-V to 5.5-V power-supply range
- VCC isolation feature – if either VCC input is at GND, both ports are in the high-impedance state
- DIR input circuit referenced to VCCA
- Low power consumption, 4-µA maximum ICC
- Available in the Texas Instruments NanoFree™ package
- ±24-mA output drive at 3.3 V
- Ioff supports Partial-Power-Down mode operation
- Maximum data rates:
- 420 Mbps (3.3-V to 5-V translation)
- 210 Mbps (translate to 3.3 V)
- 140 Mbps (translate to 2.5 V)
- 75 Mbps (translate to 1.8 V)
- Latch-up performance exceeds 100 mA per JESD 78, Class II
- ESD protection exceeds JESD 22
- 4000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)
- 1000-V Charged-Device Model (C101)
This dual-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.65V to 5.5V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.65V to 5.5V. This allows for universal low-voltage bidirectional translation between any of the 1.8V, 2.5V, 3.3V, and 5V voltage nodes.
The SN74LVC2T45 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input activate either the B-port outputs or the A-port outputs. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports are always active and must have a logic HIGH or LOW level applied to prevent excess ICC and ICCZ.
The SN74LVC2T45 is designed so that VCCA supplies the DIR input circuit. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.
The VCC isolation feature is designed so that if either VCC input is at GND, both ports are in the high-impedance state.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | SN74LVC2T45 Dual-Bit Dual-Supply Bus Transceiver With Configurable Voltage Translation datasheet (Rev. N) | PDF | HTML | 2024. 6. 21 | |
| 애플리케이션 노트 | Schematic Checklist - A Guide to Designing With Fixed or Direction Control Translators | PDF | HTML | 2024. 10. 2 | ||
| 애플리케이션 노트 | Schematic Checklist - A Guide to Designing with Auto-Bidirectional Translators | PDF | HTML | 2024. 7. 12 | ||
| 애플리케이션 노트 | Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) | PDF | HTML | 2024. 7. 3 | ||
| 선택 가이드 | Voltage Translation Buying Guide (Rev. A) | 2021. 4. 15 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
5-8-LOGIC-EVM — 5핀~8핀 DCK, DCT, DCU, DRL 및 DBV 패키지용 일반 논리 평가 모듈
AVCLVCDIRCNTRL-EVM — AVC 및 LVC를 지원하는 방향 제어 양방향 변환 디바이스를 위한 일반 EVM
일반 EVM은 2개, 4개 및 8개 채널 LVC 및 AVC 방향 제어 변환 장치를 지원하도록 설계했습니다. 또한 동일한 개수의 채널에서 버스 홀드 및 차량용 -Q1 장치를 지원합니다. AVC는 구동 강도가 더 낮은 12mA인 저전압 변환 장치입니다. LVC는 구동 강도가 더 높은 32mA로, 1.65~5.5V의 더 높은 전압 변환 장치입니다.
TIDA-010026 — EnDat2.2 절대 인코더용 강력한 인터페이스 레퍼런스 설계
TIDA-01401 — 절대 인코더용 높은 EMC 내성 RS-485 인터페이스 레퍼런스 설계
TIDA-01630 — Tamagawa 인코더용 높은 EMC 내성 RS485 인터페이스 레퍼런스 설계
TIDM-ULTRASONIC-WATER-FLOW-MEASUREMENT — 초음파 유량 측정 레퍼런스 디자인
이 초음파 유량 측정 시스템은 1.4gpm의 낮은 넓은 유량 범위에서 매우 정확한 측정을 제공하는 데 이상적입니다. 이 설계는 개별 아날로그 부품이 있는 단일 MCU를 기반으로 합니다. 이 알고리즘은 광범위한 작동 조건에 걸쳐 유량 측정의 견고성과 성능을 향상시키는 고유한 독점 알고리즘을 사용합니다. 이 설계는 무선 AMI 네트워크를 위한 TI RF 플러그인 평가 모듈과 완벽하게 호환됩니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| DSBGA (YZP) | 8 | Ultra Librarian |
| VSSOP (DCU) | 8 | Ultra Librarian |
| SSOP (DCT) | 8 | Ultra Librarian |