SN55LVRA4-SEP
- VID V62/25606-01XE
- Total ionizing dose characterized at 30krad (Si)
- Total ionizing dose radiation lot acceptance testing (TID RLAT) for every wafer lot to 30krad (Si)
- Single-event effects (SEE) characterized:
- Single event latch-up (SEL) immune to linear energy transfer (LET) = 50MeV-cm2 /mg
- Single event transient (SET) characterization report available
- 400Mbps signaling rate
- Operates with a single 3.3V supply
- –4V to 5V extended common-mode input voltage range
- Differential input thresholds < ±50mV with 50mV of hysteresis over entire common-mode input voltage range
- Complies with TIA/EIA-644 (LVDS)
- Active fail-safe assures a high-level output with no input and input remains high-impedance on power down
- Bus-pin ESD protection exceeds 15kV HBM
- TTL control inputs are 5V tolerant
- Space enhanced plastic (SEP)
- Controlled baseline
- Gold wire, NiPdAu lead finish
- One assembly and test site, one fabrication site
- Extended product life cycle
- Military (–55°C to 125°C) temperature range
- Product traceability
- Meets NASA ASTM E595 outgassing specification
The SN55LVRA4-SEP offers the widest common-mode input voltage range in the industry. These receivers provide an input voltage range specification compatible with a 5V PECL signal as well as an overall increased ground-noise tolerance.
The SN55LVRA4-SEP include a failsafe circuit that provides a high-level output within 60ns after loss of the input signal. The most common causes of signal loss are disconnected cables, shorted lines, or powered-down transmitters. The failsafe circuit prevents noise from being received as valid data under these fault conditions.
The intended application and signaling technique of these devices is point-to-point baseband data transmission over controlled impedance media of approximately 100Ω. The transmission media can be printed-circuit board traces, backplanes, or cables. The ultimate rate and distance of data transfer is dependent upon the attenuation characteristics of the media and the noise coupling to the environment.
The SN55LVRA4-SEP is characterized for operation from –55°C to 125°C.
관심 가지실만한 유사 제품
비교 대상 장치와 유사한 기능.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | SN55LVRA4-SEP Radiation Tolerant Quad Channel High-Speed Differential Receiver datasheet (Rev. B) | PDF | HTML | 2026. 2. 19 | |
| * | 방사능 및 안정성 보고서 | SN55LVRA4-SEP Total Ionizing Dose (TID) Report | 2025. 12. 10 | ||
| * | 방사능 및 안정성 보고서 | SN55LVRA4-SEP Single-Event Effects (SEE) Radiation Report | PDF | HTML | 2025. 12. 8 | |
| * | 방사능 및 안정성 보고서 | SN55LVRA4-SEP Production Flow and Reliability Report | PDF | HTML | 2025. 11. 12 | |
| * | VID | SN55LVRA4-SEP VID SN55LVRA4-SEP VID V62-25606 | 2026. 2. 20 | ||
| 선택 가이드 | TI Space Products (Rev. L) | 2026. 3. 27 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
SN65LVDS31-33EVM — SN65LVDS31 및 SN65LVDS33용 평가 모듈
TI offers a series of low-voltage differential signaling (LVDS) evaluation modules (EVMs) designed for analysis of the electrical characteristics of LVDS drivers and receivers. Four unique EVMs are available to evaluate the different classes of LVDS devices offered by TI.
As seen in the Combination (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| SOIC (D) | 16 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.