DRV2667
- Integrated Digital Front End
- Up to 400-kHz I 2C Bus Control
- Advanced Waveform Synthesizer
- 2-kB Internal Waveform Memory
- 100-Byte Internal FIFO Interface
- Immersion TS5000-Compliant
- Optional Analog Inputs
- High-Voltage Piezo-Haptic Driver
- Drives up to 100 nF at 200 V PP and 300 Hz
- Drives up to 150 nF at 150 V PP and 300 Hz
- Drives up to 330 nF at 100 V PP and 300 Hz
- Drives up to 680 nF at 50 V PP and 300 Hz
- Differential Output
- 105-V Integrated Boost Converter
- Adjustable Boost Voltage
- Adjustable Boost Current Limit
- Programable Boost Current Limit
- Integrated Power FET and Diode
- No Transformer Required
- 2-ms Fast Start Up Time
- 3.3- to 5.5-V Wide Supply Voltage Range
- 1.8 V-Compatible, V DD-Tolerant Digital Pins
The DRV2667 device is a piezo haptic driver with integrated 105-V boost switch, integrated power diode, integrated fully-differential amplifier, and integrated digital front end capable of driving both high-voltage and low-voltage piezo haptic actuators. This versatile device supports HD haptics through the I 2C port or through the analog inputs.
The digital interface of the DRV2667 device is available through an I 2C-compatible bus. A digital interface relieves the costly processor burden of the PWM generation or additional analog channel requirements in the host system. Any writes to the internal FIFO will automatically wake up the device and begin playing the waveform after the 2-ms internal startup procedure. When the data flow stops or the FIFO under-runs, the device will automatically enter a pop-less shutdown procedure.
The DRV2667 device also includes waveform memory to store and recall waveforms with minimal latency as well as an advanced waveform synthesizer to construct complex haptic waveforms with minimal memory usage. This provide a means of hardware acceleration, relieving the host processor of haptic generation duties as well as minimizing bus traffic over the haptic interface.
The boost voltage is set using two external resistors, and the boost current limit is programmable through the R EXT resistor. A typical start-up time of 2 ms makes the DRV2667 an ideal piezo driver for fast haptic responses. Thermal overload protection prevents the device from being damaged when overdriven.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | DRV2667 Piezo Haptic Driver with Boost, Digital Front End, and Internal Waveform Memory datasheet (Rev. E) | PDF | HTML | 2022. 10. 18 | |
| 애플리케이션 노트 | DRV8662, DRV2700, DRV2665, and DRV2667 Configuration Guide (Rev. A) | PDF | HTML | 2021. 12. 8 | ||
| 사용 설명서 | Haptic Control Console GUI (Rev. B) | 2021. 10. 14 | |||
| 애플리케이션 노트 | Haptic Energy Consumption (Rev. A) | PDF | HTML | 2021. 9. 28 | ||
| 애플리케이션 노트 | Piezo Haptics With Integrated Waveforms: DRV2605L-Q1 and DRV2700 | 2017. 9. 27 | |||
| 기술 문서 | Haptics: touch screens come alive in the new HMI design | PDF | HTML | 2015. 9. 22 | ||
| Product overview | Haptic Solutions for Wearable Devices (Rev. A) | 2014. 9. 30 | |||
| Product overview | Automotive Haptics Solutions | 2013. 9. 16 | |||
| Product overview | Haptics: Touch feedback that really moves you (Rev. A) | 2013. 1. 8 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
DRV-ACC16-EVM — 햅틱 가속도계 측정 툴
DRV2667EVM-CT — DRV2667 평가 모듈(부스트, 디지털 프론트 엔드 및 내부 파형 메모리 포함)
DRV2667은 전압이 40Vpp~200Vpp인 피에조 엑추에이터를 제어하도록 설계된 디지털 제어 고전압 드라이버입니다. DRV2667은 통합 105V 부스트 컨버터 및 200Vpp 차동 출력 증폭기를 포함하여 피에조 구동 설계의 복잡성을 크게 줄여줍니다. 또한 디지털 제어 인터페이스(I2C™)에는 실시간 파형 재생, 파형 생성기 및 파형 저장용 임베디드 RAM이 포함되어 있습니다.
DRV2667EVM-CT EVM(평가 모듈) 키트는 피에조 액추에이터에 연결할 수 있는 DRV2667을 위한 완전한 데모 및 평가 플랫폼입니다. 이 (...)
DRV2667SW-LINUX — DRV2667용 Linux 드라이버
The Linux driver supports the DRV2667 haptic motor drivers. The Linux driver supports communication through the I2C bus and interfaces with the input sub-system for a forced feedback response.
Linux Mainline Status
Available in Linux Main line: Yes
Available through git.ti.com: N/A
Supported Devices:
- (...)
SLOC342 — DRV2667EVM-CT Firmware
HAPTICS-CONSOLE — Haptic Control Console v1.6.0.2
햅틱 제어 콘솔 소프트웨어는 TI의 햅틱 드라이버를 위한 평가 및 개발 제품군입니다. 햅틱 제어 콘솔 소프트웨어는 고급 촉각 피드백을 개발하기 위한 햅틱 드라이버와 타사 햅틱 액추에이터의 평가를 지원합니다.
시작하려면 햅틱 드라이버용 평가 모듈(EVM)을 USB를 통해 햅틱 제어 콘솔 소프트웨어를 사용하여 컴퓨터에 연결하여 전체 장치를 설정, 제어 및 평가하면 됩니다. 햅틱 제어 콘솔 소프트웨어에는 관련 장치를 위한 빠른 설정 콘솔, 전체 장치 레지스터 맵, 기본 장치 RAM 관리가 포함되어 있습니다.
지원되는 평가 모듈 및 (...)
TIDA-00169 — 차량용 TFT LCD 디스플레이 솔루션
This reference design implements a video over LVDS solution for automotive infotainment applications.It highlights the support of multi-touch with haptic feedback, LCD backlight control, and ambient light sensing, without the introduction of dedicated support lines back to the host processor. This (...)
TIDA-00314 — 햅틱 피드백 레퍼런스 디자인이 통합된 터치온 금속 버튼
This reference design uses our inductance-to-digital converter technology to provide a high-precision method to sense button presses on a metal surface and our haptic drivers provide high-quality haptics feedback to the user. TIDA-00314 demonstrates techniques for system design, environmental (...)
TIDA-00408 — 빌딩 자동화 및 의료 애플리케이션을 위한 햅틱 피드백 커패시티브 터치 디스플레이 레퍼런스 디자인
The TIDA-00408 Touch Display with Haptic Feedback reference design showcases haptics for thermostats, building automation, factory automation, point of sale, and automotive applications. The touch screen provides touch feedback when the user interacts with the on-screen user interface. (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| VQFN (RGP) | 20 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.