Home Schalter und Multiplexer Analogschalter und Multiplexer Protokoll- & Busschalter & -multiplexer
Home
Schalter und Multiplexer
Analogschalter und Multiplexer
Protokoll- & Busschalter & -multiplexer

SN74CB3Q3251

AKTIV

1-kanaliger Universal-FET-Busschalter, 3,3 V, 8:1

Jetzt bestellen
Datenblatt

SN74CB3Q3251

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Protocols Analog Configuration 8:1 Number of channels 1 Bandwidth (MHz) 500 Ron (typ) (mΩ) 3500 Input/output voltage (min) (V) 0 Input/output voltage (max) (V) 5.5 Supply current (typ) (µA) 600 Operating temperature range (°C) -40 to 85 ESD CDM (kV) 1 Input/output continuous current (max) (mA) 64 COFF (typ) (pF) 3.5 CON (typ) (pF) 15 OFF-state leakage current (max) (µA) 1 Ron (max) (mΩ) 11000 VIH (min) (V) 1.7 VIL (max) (V) 0.8 Rating Catalog
Protocols Analog Configuration 8:1 Number of channels 1 Bandwidth (MHz) 500 Ron (typ) (mΩ) 3500 Input/output voltage (min) (V) 0 Input/output voltage (max) (V) 5.5 Supply current (typ) (µA) 600 Operating temperature range (°C) -40 to 85 ESD CDM (kV) 1 Input/output continuous current (max) (mA) 64 COFF (typ) (pF) 3.5 CON (typ) (pF) 15 OFF-state leakage current (max) (µA) 1 Ron (max) (mΩ) 11000 VIH (min) (V) 1.7 VIL (max) (V) 0.8 Rating Catalog
TSSOP (PW) 16 32 mm² (5 mm × 6.4 mm) SSOP (DBQ) 16 29.4 mm² (4.9 mm × 6 mm) TVSOP (DGV) 16 23.04 mm² (3.6 mm × 6.4 mm) VQFN (RGY) 16 14 mm² (4 mm × 3.5 mm)
  • High-bandwidth data path (up to 500MHz)
  • Equivalent to IDTQS3VH251 device
  • 5V tolerant I/Os with device powered up or powered down
  • Low and flat ON-state resistance (ron) characteristics over operating range (ron = 4Ω Typ)
  • Rail-to-rail switching on data I/O ports
    • 0 to 5V switching with 3.3V VCC
    • 0 to 3.3V switching with 2.5V VCC
  • Bidirectional data flow with near-zero propagation delay
  • Low input/output capacitance minimizes loading and signal distortion (Cio(OFF) = 3.5 pF Typ)
  • Fast switching frequency (fOE or fS = 20 MHz Max). For additional information regarding the performance characteristics of the CB3Q family, refer to the TI application note, CBT-C, CB3T, and CB3Q Signal-Switch Families.
  • Data and controlinputs provide undershoot clamp diodes
  • Low power consumption (ICC = 1mA Typ)
  • VCC operating range from 2.3V to 3.6V
  • Data I/Os support 0 to 5V signaling levels (0.8V, 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, 5V)
  • Control inputs can be driven by TTL or 5V/3.3V CMOS outputs
  • Ioff supports partial-power-down mode operation
  • Latch-Up performance exceeds 100mA per JESD 78, class II
  • ESD performance tested per JESD 22
    • 2000V human-body model (A114B, Class II)
    • 1000V charged-device model (C101)
  • Supports both digital and analog applications: PCI interface, differential signal interface, memory interleaving, bus isolation, low-distortion signal gating
  • High-bandwidth data path (up to 500MHz)
  • Equivalent to IDTQS3VH251 device
  • 5V tolerant I/Os with device powered up or powered down
  • Low and flat ON-state resistance (ron) characteristics over operating range (ron = 4Ω Typ)
  • Rail-to-rail switching on data I/O ports
    • 0 to 5V switching with 3.3V VCC
    • 0 to 3.3V switching with 2.5V VCC
  • Bidirectional data flow with near-zero propagation delay
  • Low input/output capacitance minimizes loading and signal distortion (Cio(OFF) = 3.5 pF Typ)
  • Fast switching frequency (fOE or fS = 20 MHz Max). For additional information regarding the performance characteristics of the CB3Q family, refer to the TI application note, CBT-C, CB3T, and CB3Q Signal-Switch Families.
  • Data and controlinputs provide undershoot clamp diodes
  • Low power consumption (ICC = 1mA Typ)
  • VCC operating range from 2.3V to 3.6V
  • Data I/Os support 0 to 5V signaling levels (0.8V, 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, 5V)
  • Control inputs can be driven by TTL or 5V/3.3V CMOS outputs
  • Ioff supports partial-power-down mode operation
  • Latch-Up performance exceeds 100mA per JESD 78, class II
  • ESD performance tested per JESD 22
    • 2000V human-body model (A114B, Class II)
    • 1000V charged-device model (C101)
  • Supports both digital and analog applications: PCI interface, differential signal interface, memory interleaving, bus isolation, low-distortion signal gating

The SN74CB3Q3251 is a high-bandwidth FET bus switch utilizing a charge pump to elevate the gate voltage of the pass transistor, providing a low and flat ON-state resistance (ron). The low and flat ON-state resistance allows for minimal propagation delay and supports rail-to-rail switching on the data input/output (I/O) ports. The device also features low data I/O capacitance to minimize capacitive loading and signal distortion on the data bus. Specifically designed to support high-bandwidth applications, the SN74CB3Q3251 provides an optimized interface solution ideally suited for broadband communications, networking, and data-intensive computing systems.

The SN74CB3Q3251 is a 1-of-8 multiplexer/demultiplexer with a single output-enable ( OE) input. The select (S0, S1, S2) inputs control the data path of the multiplexer/demultiplexer. When OE is low, the multiplexer/demultiplexer is enabled, and the A port is connected to the B port, allowing bidirectional data flow between ports. When OE is high, the multiplexer/demultiplexer is disabled, and a high-impedance state exists between the A and B ports.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry prevents damaging current backflow through the device when it is powered down. The device has isolation during power off.

To ensure the high-impedance state during power up or power down, OE must be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

The SN74CB3Q3251 is a high-bandwidth FET bus switch utilizing a charge pump to elevate the gate voltage of the pass transistor, providing a low and flat ON-state resistance (ron). The low and flat ON-state resistance allows for minimal propagation delay and supports rail-to-rail switching on the data input/output (I/O) ports. The device also features low data I/O capacitance to minimize capacitive loading and signal distortion on the data bus. Specifically designed to support high-bandwidth applications, the SN74CB3Q3251 provides an optimized interface solution ideally suited for broadband communications, networking, and data-intensive computing systems.

The SN74CB3Q3251 is a 1-of-8 multiplexer/demultiplexer with a single output-enable ( OE) input. The select (S0, S1, S2) inputs control the data path of the multiplexer/demultiplexer. When OE is low, the multiplexer/demultiplexer is enabled, and the A port is connected to the B port, allowing bidirectional data flow between ports. When OE is high, the multiplexer/demultiplexer is disabled, and a high-impedance state exists between the A and B ports.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry prevents damaging current backflow through the device when it is powered down. The device has isolation during power off.

To ensure the high-impedance state during power up or power down, OE must be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
filter Andere Protokoll- & Busschalter & -multiplexer suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 4
Top-Dokumentation Typ Titel Format-Optionen Neueste englische Version herunterladen Datum
* Datenblatt SN74CB3Q3251 1-of-8 FET Multiplexer/Demultiplexer 2.5V-3.3V Low-voltage High-bandwidth BUS Switch datasheet (Rev. B) PDF | HTML 21.08.2026
Anwendungshinweis Selecting the Correct Texas Instruments Signal Switch (Rev. E) PDF | HTML 02.06.2022
Anwendungshinweis Multiplexers and Signal Switches Glossary (Rev. B) PDF | HTML 01.12.2021
Application brief Eliminate Power Sequencing with Powered-off Protection Signal Switches (Rev. C) PDF | HTML 06.01.2021

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Schnittstellenadapter

LEADED-ADAPTER1 — Oberflächenmontierbarer DIP-Header-Adapter zur schnellen Prüfung der 5-, 8-, 10-, 16- und 24-poligen

Die EVM-LEADED1-Platine ermöglicht schnelles Testen und Testbrettaufbauten von gängigen bleihaltigen Gehäusen von TI.  Die Platine verfügt über Anschlussflächen, um die oberflächenmontierten Gehäuse D, DBQ, DCT,DCU, DDF, DGS, DGV und PW von TI in 100-mil-DIP-Stiftleisten umzuwandeln.     

Benutzerhandbuch: PDF
Unterstützte Produkte und Hardware
Vorrätig
Limit:
??asset.out-of-stock-ti_de_DE??
Nicht verfügbar
Schnittstellenadapter

LEADLESS-ADAPTER1 — Oberflächenmontierbarer DIP-Header-Adapter zum Testen der 6-, 8-, 10-, 12-, 14-, 16- und 20-poligen

Die EVM-LEADLESS1-Platine ermöglicht schnelles Testen und Testbrettaufbauten von gängigen bleifreien Gehäusen von TI.  Die Platine verfügt über Anschlussflächen, um die oberflächenmontierten Gehäuse DRC, DTP, DQE, RBW, RGY, RSE, RSV, RSW RTE, RTJ, RUK , RUC, RUG, RUM, RUT und YZP von TI in (...)
Benutzerhandbuch: PDF
Unterstützte Produkte und Hardware
Vorrätig
Limit:
??asset.out-of-stock-ti_de_DE??
Nicht verfügbar
Simulationsmodell

SN74CB3Q3251 IBIS Model

SCDM077.ZIP (42 KB) - IBIS-Modell
Unterstützte Produkte und Hardware
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
TSSOP (PW) 16 Ultra Librarian
SSOP (DBQ) 16 Ultra Librarian
TVSOP (DGV) 16 Ultra Librarian
VQFN (RGY) 16 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos