ZHCS310G JANUARY   2009  – September 2015 UCC28610

PRODUCTION DATA.  

  1. 特性
  2. 应用
  3. 说明
  4. 修订历史记录
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Fault Recovery
      2. 7.3.2 Maximum On-Time and Brown Out
      3. 7.3.3 External Shutdown Using the MOT Pin
      4. 7.3.4 Overvoltage Detection
      5. 7.3.5 Solving for High Frequency Ringing
        1. 7.3.5.1 Identification of High Frequency Ringing
        2. 7.3.5.2 Avoid HF Ringing
        3. 7.3.5.3 Ferrite Chip or Bead Solution
        4. 7.3.5.4 DRV Capacitor Solution
        5. 7.3.5.5 Gate Turn-Off Resistor Solution
      6. 7.3.6 Thermal Shutdown
    4. 7.4 Device Functional Modes
  8. Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Transformer Selection
      2. 8.1.2 Cascode Bias and Start-Up
      3. 8.1.3 Feedback Function
      4. 8.1.4 Modulation Modes
      5. 8.1.5 Primary Current Sense
      6. 8.1.6 Zero Crossing Detection
      7. 8.1.7 Green Mode Operation
      8. 8.1.8 Maximum Converter Power Limitation
      9. 8.1.9 Minimum Converter Power Limitation
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Input Bulk Capacitance and Minimum Bulk Voltage
        2. 8.2.2.2 Transformer Selection
        3. 8.2.2.3 Feedback Function
      3. 8.2.3 Application Curves
  9. Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11器件和文档支持
    1. 11.1 社区资源
    2. 11.2 商标
    3. 11.3 静电放电警告
    4. 11.4 Glossary
  12. 12机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Specifications

Absolute Maximum Ratings

All voltages are with respect to GND, –40°C < TJ = TA < 125°C, all currents are positive into and negative out of the specified terminal (unless otherwise noted) (1)
MIN MAX UNIT
Input voltage range VDD –0.5 25 V
DRV, during conduction –0.5 2.0
DRV, during non-conduction 20
VGG (2) –0.5 16
ZCD, MOT, CL (3) –0.5 7
FB (3) –0.5 1.0
VDD – VGG –7 10
Continuous input current IVGG (2) 10 mA
Input current range IZCD, IMOT, ICL, IFB (3) –3 1
Peak output current DRV -5 A
DRV, pulsed 200ns, 2% duty cycle –5 1.5
TJ Operating junction temperature, –40 150 °C
Lead Temperature (soldering, 10 sec.) 260 °C
Tstg Storage temperature range –65 150 °C
These are stress ratings only. Stress beyond these limits may cause permanent damage to the device. Functional operation of the device at these or any conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute maximum rated conditions for extended periods of time may affect device reliability
Voltage on VGG is internally clamped. The clamp level varies with operating conditions. In normal use, VGG is current fed with the voltage internally limited
In normal use, MOT, CL, ZCD, and FB are connected to resistors to GND and internally limited in voltage swing

ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (1) 1500 V
Charged device model (CDM), per JEDEC specification JESD22-C101, all pins (2) 500
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

Recommended Operating Conditions

Unless otherwise noted, all voltages are with respect to GND, -40°C < TJ = TA < 125°C. Components reference, Figure 34.
MIN MAX UNIT
VDD Input voltage 9 20 V
VGG Input voltage from low-impedance source 9 13 V
IVGG Input current from a high-impedance source 10 2000 μA
RMOT Resistor to GND Shutdown/Retry mode 25 100
Latch-off mode 150 750
RCL Resistor to GND 24.3 100
RZCD1 Resistor to auxiliary winding 50 200
CVGG VGG capacitor 33 200 nF
CBP VDD bypass capacitor, ceramic 0.1 1 μF

Thermal Information

THERMAL METRIC (1) UCC28610 UNIT
D (SOIC) P (PDIP)
8 PINS 8 PINS
RθJA Junction-to-ambient thermal resistance 117.5 56.3 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 63.7 45.7 °C/W
RθJB Junction-to-board thermal resistance 57.8 33.5 °C/W
ψJT Junction-to-top characterization parameter 15.3 22.9 °C/W
ψJB Junction-to-board characterization parameter 57.3 33.4 °C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953.

Electrical Characteristics

Unless otherwise stated: VDD = 12 V, VGG = 12 V, ZCD = 1 V, IFB = 10 µA, GND = 0 V, a 0.1-μF capacitor between VDD and GND, a 0.1-μF capacitor between VGG and GND, RCL = 33.2 kΩ, RMOT = 380 kΩ, –40°C < TA < +125°C, TJ = TA
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VDD and VGG SUPPLY
VGG(OPERATING) VGG voltage, operating VDD = 14 V, IVGG = 2.0 mA 13 14 15 V
VGG(DISABLED) VGG voltage, PWM disabled VDD = 12 V, IVGG = 15 μA, IFB = 350 μA 15 16 17 V
ΔVGG Rise in VGG clamping voltage during UVLO, GM, or Fault VGG(DISABLED) – VGG(OPERATING) 1.75 2.00 2.15 V
IVGG(SREG) VGG shunt regulator current VGG = VGG(DISABLED) -100 mV, VDD = 12 V 6 10 μA
ΔVGG(SREG) VGG shunt load regulation 10 μA ≤ IVGG ≤ 5 mA, IFB = 350 μA 125 200 mV
VGG(LREG) VGG LDO regulation voltage VDD = 20 V, IVGG = – 2 mA 13 V
VGG(LREG, DO) VGG LDO Dropout Voltage VDD – VGG, VDD = 11 V, IVGG = – 2 mA 1.5 2 2.5 V
VDD(ON) UVLO turn-on threshold 9.7 10.2 10.7 V
VDD(OFF) UVLO turn-off threshold 7.55 8 8.5 V
ΔVDD(UVLO) UVLO hysteresis 1.9 2.2 2.5 V
IVDD(OPERATING) Operating current VDD = 20 V 2.5 3 3.7 mA
IVDD(GM) Idle current between bursts IFB = 350 μA 550 900 μA
IVDD(UVLO) Current for VDD < UVLO VDD = VDD(ON) – 100 mV, increasing 225 310 μA
RDS,ON(VDD) VDD Switch on resistance, DRV to VDD VGG = 12 V, VDD = 7V, IDRV = 50 mA 4 10 Ω
VDD(FAULT RESET) VDD for fault latch reset 5.6 6 6.4 V
MODULATION
tS(HF) (1) Minimum switching period, frequency modulation (FM) mode IFB = 0 μA, (1) 7.125 7.5 7.875 μs
tS(LF) (1) Maximum switching period, reached at end of FM modulation range IFB = IFB, CNR3 – 20 μA, (1) 31 34 38 μs
IDRVpk(max) Maximum peak driver current over amplitude modulation(AM) range IFB = 0 μA, RCL = 33. 2 kΩ 2.85 3 3.15 A
IFB = 0 μA, RCL = 100 kΩ 0.80 0.90 1.0
IDRVpk(min) Minimum peak driver current reached at end of AM modulation range IFB, CNR2 + 10 μA, RCL = 33.2 kΩ 0.7 0.85 1.1 A
IFB, CNR2 + 10 μA, RCL = 100 kΩ 0.2 0.33 0.5
KP Maximum power constant IDRVpk(max) = 3 A 0.54 0.60 0.66 W/μH
IDRVpk(absmin) Minimum peak driver independent of RCL or AM control RCL = OPEN 0.3 0.45 0.6 A
tBLANK(Ilim) Leading edge current limit blanking time IFB = 0 μA, RCL = 100 kΩ, 1.2-A pull-up on DRV 120 220 450 ns
VCL Voltage of CL pin IFB = 0 μA 2.94 3 3.06 V
IFB = (IFB,CNR3 – 20 μA) (1) 0.95 1.00 1.10
IFB,CNR1 (4) IFB range for FM modulation IFB increasing, tS = tS(LF),
IDRVpk = IDRVpk(max)
145 165 195 μA
IFB,CNR2 – IFB,CNR1 (4) IFB range for AM modulation tS = tS(LF), IDRVpk ranges from
IDRVpk(max) to IDRVpk(min)
35 45 65 μA
IFB,CNR3 – IFB,CNR2 (4) IFB range for Green Mode (GM) modulation IFB increasing until PWM action is disabled entering a burst-off state 45 70 90 μA
IFB, GM-HYST (4) IFB hysteresis during GM modulation to enter burst on and off states IFB decreasing from above IFB,CNR3 10 25 40 μA
VFB Voltage of FB pin IFB = 10 μA 0.34 0.7 0.84 V
ZERO CROSSING DETECTION
ZCD(TH) ZCD zero crossing threshold ZCD high to low generates switching period (tS has expired) 5 20 50 mV
ZCD(CLAMP) ZCD low clamp voltage IZCD = –10 μA -220 -160 -100 mV
ZCD(START) ZCD voltage threshold to enable the internal start timer Driver switching periods generated at start timer rate 0.1 0.15 0.2 V
tDLY(ZCD) Delay from zero crossing to Driver turn-on 150-Ω pull-up to 12-V on DRV 150 ns
tWAIT(ZCD) Wait time for zero crossing detection Driver turn-on edge generated following tS with previous zero crossing detected 2 2.4 2.8 μs
tST Starter time-out period ZCD = 0 V 150 240 300
DRIVER
RDS(on)(DRV) Driver on-resistance IDRV = 4.0 A 90 190
IDRV(OFF) Driver off-leakage current DRV = 12 V 1.5 20 μA
RDS(on)(HSDRV) High-side driver on-resistance IDRV = –50 mA 6 11 Ω
IDRV(DSCH) DRV bulk discharge current VDD open, DRV= 12 V, Fault latch set 2 2.8 3.6 mA
OVERVOLTAGE FAULT
ZCD(OVP) Overvoltage fault threshold at ZCD Fault latch set 4.85 5 5.15 V
tBLANK(OVP) ZCD blanking and OVP sample time from the turn-off edge of DRV 0.6 1 1.7 μs
IZCD(bias) ZCD Input bias current ZCD = 5 V -0.1 -0.05 0.1 μA
OVERLOAD FAULT
IFB(OL) Current to trigger overload delay timer 0 1.5 3 μA
tOL Delay to overload fault IFB = 0 A continuously 200 250 325 ms
tRETRY Retry delay in retry mode or after shutdown command RMOT = 76 kΩ 750 ms
RMOT(TH) Boundary RMOT between latch-off and retry modes See (2) 100 120 150
SHUTDOWN THRESHOLD
MOT(SR) Shutdown-Retry threshold MOT high to low 0.7 1 1.3 V
IMOT MOT current when MOT is pulled low MOT = 1 V –600 –450 –300 μA
MAXIMUM ON TIME
tMOT Latch-OFF RMOT = 383 kΩ 3.43 3.83 4.23 μs
Shutdown-retry RMOT = 76 kΩ 3.4 3.8 4.2
MOT MOT voltage 2.7 3 3.3 V
THERMAL SHUTDOWN
TSD (3) Shutdown temperature TJ, temperature rising (3) 165 °C
TSD_HYS (3) Hysteresis TJ, temperature falling, degrees below TSD (3) 15 °C
tS sets a minimum switching period. Following the starting edge of a PWM on time, under normal conditions, the next on time is initiated following the first zero crossing at ZCD after tS. The value of tS is modulated by IFB between a minimum of tS(HF) and a maximum of tS(LF) In normal operation, tS(HF) sets the maximum operating frequency of the power supply and tS(LF) sets the minimum operating frequency of the power supply.
A latch-off or a shutdown and retry fault response to a sustained overload is selected by the range of RMOT.
To select the latch-off mode, RMOT should be greater than 150 kΩ and tMOT is given by RMOT × (1.0 × 10-11).
To select the shutdown-retry mode, RMOT should be less than 100 kΩ and tMOT is given by RMOT × (5.0 × 10-11).
Thermal shutdown occurs at temperatures higher than the normal operating range. Device performance at or near thermal shutdown temperature is not specified or assured.
Refer to Figure 1.
UCC28610 fig2new_lus888.gif Figure 1. FB Electrical Condition Detail

Typical Characteristics

Unless otherwise stated: VDD = 12 V, VGG = 12 V, ZCD = 1 V, IFB = 10 µA, GND = 0 V, a 0.1-μF capacitor between VDD and GND, a 0.1-μF capacitor between VGG and GND, RCL = 33.2 kΩ, RMOT = 380 kΩ, –40°C < TA < +125°C, TJ = TA
UCC28610 ivdd1_vs_vvdd_lus888.gif Figure 2. Bias Supply Current vs Bias Supply Voltage During Operation
UCC28610 ivdd_vs_tj_lus888.gif Figure 4. Bias Supply Current vs Temperature During Green Mode
UCC28610 fsw_vs_ifb_lus888.gif Figure 6. Oscillator Frequency vs Feedback Current
UCC28610 tswlf_vs_ta_lus888.gif Figure 8. Switching Period During Amplitude Modulaltion vs Ambient Temperature
UCC28610 idrvpk_vs_gm_lus888.gif Figure 10. Peak DRV Current vs Transconductance (1/RCL)
UCC28610 tonmax_vs_rmot_lus888.gif Figure 12. Maximum On Time vs Maximum On-Time Resistance
UCC28610 rdson2_vs_ta_lus888.gif Figure 14. Driver RDS(on) vs Ambient Temperature
UCC28610 pdiss_vs_tb_lus888.gif Figure 16. Safe Operating Area vs Board Temperature
UCC28610 ivdd2_vs_vvdd_lus888.gif Figure 3. Bias Supply Current vs Bias Supply Voltage During Green Mode
UCC28610 ivdd3_vs_vvdd_lus888.gif Figure 5. Operational IVDD – Bias Current vs Bias Voltage
UCC28610 tswhf_vs_ta_lus888.gif Figure 7. Minimum Switching Period vs Temperature
UCC28610 idrvpk_vs_ifb_lus888.gif Figure 9. Peak DRV Current vs Feedback Current
UCC28610 idrvpk_vs_ta_lus888.gif Figure 11. Peak DRV Current vs Ambient Temperature
UCC28610 tonmax_vs_tj_lus888.gif Figure 13. Maximum On Time vs Junction Temperature
UCC28610 rdson_vs_ta_lus888.gif Figure 15. RDS(on) of High Side Drive and VDD Switch vs Temperature
UCC28610 thetajb_vs_pdis_lus888.gif Figure 17. Thermal Coefficient – θJB vs Power Dissipation