SLVSB57C March   2012  – January 2016 TPS54060A

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Fixed Frequency PWM Control
      2. 7.3.2  Slope Compensation Output Current
      3. 7.3.3  Bootstrap Voltage (BOOT)
      4. 7.3.4  Low Dropout Operation
      5. 7.3.5  Error Amplifier
      6. 7.3.6  Voltage Reference
      7. 7.3.7  Adjusting the Output Voltage
      8. 7.3.8  Enable and Adjusting Undervoltage Lockout
      9. 7.3.9  Slow Start/Tracking Pin (SS/TR)
      10. 7.3.10 Overload Recovery Circuit
      11. 7.3.11 Sequencing
      12. 7.3.12 Constant Switching Frequency and Timing Resistor (RT/CLK Pin)
      13. 7.3.13 Overcurrent Protection and Frequency Shift
      14. 7.3.14 Selecting the Switching Frequency
      15. 7.3.15 How to Interface to RT/CLK Pin
      16. 7.3.16 Power Good (PWRGD Pin)
      17. 7.3.17 Overvoltage Transient Protection
      18. 7.3.18 Thermal Shutdown
      19. 7.3.19 Small Signal Model for Loop Response
      20. 7.3.20 Simple Small Signal Model for Peak Current Mode Control
      21. 7.3.21 Small Signal Model for Frequency Compensation
    4. 7.4 Device Functional Modes
      1. 7.4.1 Pulse Skip Eco-Mode
      2. 7.4.2 Normal Operation
      3. 7.4.3 Standby Operation
  8. Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1  Selecting the Switching Frequency
        2. 8.2.2.2  Output Inductor Selection (LO)
        3. 8.2.2.3  Output Capacitor
        4. 8.2.2.4  Catch Diode
        5. 8.2.2.5  Input Capacitor
        6. 8.2.2.6  Slow Start Capacitor
        7. 8.2.2.7  Bootstrap Capacitor Selection
        8. 8.2.2.8  Under Voltage Lock Out Set Point
        9. 8.2.2.9  Output Voltage and Feedback Resistors Selection
        10. 8.2.2.10 Compensation
        11. 8.2.2.11 Power Dissipation Estimate
      3. 8.2.3 Application Curves
    3. 8.3 System Examples
  9. Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
      2. 11.1.2 Development Support
    2. 11.2 Community Resources
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

6 Specifications

6.1 Absolute Maximum Ratings(1)

over operating temperature range (unless otherwise noted).
MIN MAX UNIT
Input voltage VIN –0.3 65 V
EN –0.3 5
BOOT 73
VSENSE –0.3 3
COMP –0.3 3
PWRGD –0.3 6
SS/TR –0.3 3
RT/CLK –0.3 3.6
Output voltage BOOT-PH 8 V
PH –0.6 65
PH, 10-ns Transient –2 65
Voltage Difference PAD to GND ±200 mV
Source current EN 100 μA
BOOT 100 mA
VSENSE 10 μA
PH Current Limit A
RT/CLK 100 μA
Sink current VIN Current Limit A
COMP 100 μA
PWRGD 10 mA
SS/TR 200 μA
Operating junction temperature –40 150 °C
Storage temperature –65 150 °C
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditionsRecommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

6.2 ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) QSS 009-105 (JESD22-A114A) ±2000 V
Charged-device model (CDM), per JEDEC specification JESD22-C101(2) QSS 009-147 (JESD22-C101B.01) ±500
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. .
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. .

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN MAX UNIT
VIN Supply input voltage range 3.5 60 V
VO Output voltage range 0.8 58 V
IO Output current range 0 0.5 A
TJ Junction Temperature –40 150 °C

6.4 Thermal Information

THERMAL METRIC(1) TPS54060A UNIT
DGQ (HVSSOP) DRC (VSON)
10 PINS 10 PINS
RθJA Junction-to-ambient thermal resistance 62.5 40 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 1.7 0.6 °C/W
RθJB Junction-to-board thermal resistance 20.1 7.5 °C/W
ψJT Junction-to-top characterization parameter 83 65 °C/W
ψJB Junction-to-board characterization parameter 21 7.8 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance 28 8 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953.

6.5 Electrical Characteristics

TJ = –40°C to 150°C, VIN = 3.5 to 60V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY VOLTAGE (VIN PIN)
Operating input voltage 3.5 60 V
Internal undervoltage lockout threshold No voltage hysteresis, rising and falling 2.5 V
Shutdown supply current EN = 0 V, 25°C, 3.5 V ≤ VIN ≤ 60 V 1.3 4 μA
Operating : nonswitching supply current VSENSE = 0.83 V, VIN = 12 V, 25°C 116 136
ENABLE AND UVLO (EN PIN)
Enable threshold voltage No voltage hysteresis, rising and falling, 25°C 1.11 1.25 1.36 V
Input current Enable threshold +50 mV –3.8 μA
Enable threshold –50 mV –0.9
Hysteresis current 1.91 2.95 3.99 μA
VOLTAGE REFERENCE
Voltage reference TJ = 25°C 0.792 0.8 0.808 V
0.784 0.8 0.816
HIGH-SIDE MOSFET
On-resistance VIN = 3.5 V, BOOT-PH = 3 V 300
VIN = 12 V, BOOT-PH = 6 V 200 410
ERROR AMPLIFIER
Input current 50 nA
Error amplifier transconductance (gM) –2 μA < ICOMP < 2 μA, VCOMP = 1 V 97 μMhos
Error amplifier transconductance (gM) during slow start –2 μA < ICOMP < 2 μA, VCOMP = 1 V,
VVSENSE = 0.4 V
26 μMhos
Error amplifier dc gain VVSENSE = 0.8 V 10,000 V/V
Error amplifier bandwidth 2700 kHz
Error amplifier source/sink V(COMP) = 1 V, 100 mV overdrive ±7 μA
COMP to switch current transconductance 1.9 A/V
CURRENT LIMIT
Current limit threshold VIN = 12 V, TJ = 25°C 0.6 0.94 A
THERMAL SHUTDOWN
Thermal shutdown 182 °C
TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK PIN)
Switching Frequency Range using RT mode 100 2500 kHz
fSW Switching frequency RT = 200 kΩ 450 581 720 kHz
Switching Frequency Range using CLK mode 300 2200 kHz
Minimum CLK input pulse width 40 ns
RT/CLK high threshold 1.9 2.2 V
RT/CLK low threshold 0.5 0.7 V
RT/CLK falling edge to PH rising edge delay Measured at 500 kHz with RT resistor in series 60 ns
PLL lock in time Measured at 500 kHz 100 μs
SLOW START AND TRACKING (SS/TR)
Charge current VSS/TR = 0.4 V 2 μA
SS/TR-to-VSENSE matching VSS/TR = 0.4 V 45 mV
SS/TR-to-reference crossover 98% nominal 1.0 V
SS/TR discharge current (overload) VSENSE = 0 V, V(SS/TR) = 0.4 V 112 μA
SS/TR discharge voltage VSENSE = 0 V 54 mV
POWER GOOD (PWRGD PIN)
VVSENSE VSENSE threshold VSENSE falling 92%
VSENSE rising 94%
VSENSE rising 109%
VSENSE falling 107%
Hysteresis VSENSE falling 2%
Output high leakage VSENSE = VREF, V(PWRGD) = 5.5 V, 25°C 10 nA
On resistance I(PWRGD) = 3 mA, VSENSE < 0.79 V 50 Ω
Minimum VIN for defined output V(PWRGD) < 0.5 V, II(PWRGD) = 100 μA 0.95 1.5 V

6.6 Typical Characteristics

TPS54060A C001_SLVS919.gif Figure 1. On Resistance vs Junction Temperature
TPS54060A C003_SLVS919.gif Figure 3. Switch Current Limit vs Junction Temperature
TPS54060A C005_SLVS919.gif Figure 5. Switching Frequency vs RT/CLK Resistance High Frequency Range
TPS54060A C007_SLVS919.gif Figure 7. EA Transconductance During Slow Start vs Junction Temperature
TPS54060A C009_SLVS919.gif Figure 9. EN Pin Voltage vs Junction Temperature
TPS54060A C011_SLVS919.gif Figure 11. EN Pin Current vs Junction Temperature
TPS54060A C013_SLVS919.gif Figure 13. SS/TR Discharge Current vs Junction Temperature
TPS54060A C015_SLVS919.gif Figure 15. Shutdown Supply Current vs Junction Temperature
TPS54060A C017_SLVS919.gif Figure 17. VIN Supply Current vs Junction Temperature
TPS54060A C019_SLVS919.gif Figure 19. PWRGD on Resistance vs Junction Temperature
TPS54060A C021_SLVS919.gif Figure 21. BOOT-PH UVLO vs Junction Temperature
TPS54060A C023_SLVS919.gif Figure 23. SS/TR To VSENSE Offset vs VSENSE
TPS54060A C002_SLVS919.gif Figure 2. Voltage Reference vs Junction Temperature
TPS54060A C004_SLVS919.gif Figure 4. Switching Frequency vs Junction Temperature
TPS54060A C006_SLVS919.gif Figure 6. Switching Frequency vs RT/CLK Resistance Low Frequency Range
TPS54060A C008_SLVS919.gif Figure 8. EA Transconductance vs Junction Temperature
TPS54060A C010_SLVS919.gif Figure 10. EN Pin Current vs Junction Temperature
TPS54060A C012_SLVS919.gif Figure 12. SS/TR Charge Current vs Junction Temperature
TPS54060A C014_SLVS919.gif Figure 14. Switching Frequency vs VSENSE
TPS54060A C016_SLVS919.gif Figure 16. Shutdown Supply Current vs Input Voltage (Vin)
TPS54060A C018_SLVS919.gif Figure 18. VIN Supply Current vs Input Voltage
TPS54060A C020_SLVS919.gif Figure 20. PWRGD Threshold vs Junction Temperature
TPS54060A C022_SLVS919.gif Figure 22. Input Voltage (UVLO) vs Junction Temperature
TPS54060A C024_SLVS919.gif Figure 24. SS/TR To VSENSE Offset vs Temperature