ZHCS491B August   2011  – December 2014 TPA2025D1

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用范围
  3. 3 说明
  4. 4 简化应用示意图
  5. 5 修订历史记录
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Operating Characteristics
    7. 8.7 Typical Characteristics
  9. 9 Parameter Measurement Information
  10. 10Detailed Description
    1. 10.1 Overview
    2. 10.2 Functional Block Diagram
    3. 10.3 Feature Description
      1. 10.3.1 Battery Tracking Automatic Gain Control (AGC)
      2. 10.3.2 Boost Converter Auto Pass Through (APT)
      3. 10.3.3 Short Circuit Auto-Recovery
      4. 10.3.4 Thermal Protection
      5. 10.3.5 Operation with DACS and Codecs
    4. 10.4 Device Functional Modes
      1. 10.4.1 Operation Below AGC Threshold
      2. 10.4.2 Shutdown Mode
  11. 11Application and Implementation
    1. 11.1 Application Information
    2. 11.2 Typical Application
      1. 11.2.1 Design Requirements
      2. 11.2.2 Detailed Design Procedure
        1. 11.2.2.1 Boost Converter Component Section
          1. 11.2.2.1.1 Inductor Equations
          2. 11.2.2.1.2 Boost Converter Capacitor Selection
          3. 11.2.2.1.3 Boost Terms
        2. 11.2.2.2 Input Capacitors
        3. 11.2.2.3 Speaker Load Limitation
      3. 11.2.3 Application Curve
  12. 12Power Supply Recommendations
    1. 12.1 Power Supply Decoupling Capacitors
  13. 13Layout
    1. 13.1 Layout Guidelines
    2. 13.2 Layout Example
  14. 14器件和文档支持
    1. 14.1 商标
    2. 14.2 静电放电警告
    3. 14.3 术语表
  15. 15机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

13 Layout

13.1 Layout Guidelines

Decoupling capacitors should be placed as close to the supply voltage pin as possible. For this device a 10-µF high-quality ceramic capacitor is recommended.

Table 3. Land Pattern Dimensions(1)(3)(2)(4)

SOLDER PAD
DEFINITIONS		 COPPER
PAD		 SOLDER MASK (5)
OPENING		 COPPER
THICKNESS		 STENCIL (6)(7)
OPENING		 STENCIL
THICKNESS
Nonsolder mask defined (NSMD) 275 μm
(+0.0, -25 μm)		 375 μm (+0.0, -25 μm) 1 oz max (32 μm) 275 μm x 275 μm Sq.
(rounded corners)		 125 μm thick
(1) Circuit traces from NSMD defined PWB lands should be 75 μm to 100 μm wide in the exposed area inside the solder mask opening. Wider trace widths reduce device stand off and impact reliability.
(2) Recommend solder paste is Type 3 or Type 4.
(3) Best reliability results are achieved when the PWB laminate glass transition temperature is above the operating the range of the intended application.
(4) For a PWB using a Ni/Au surface finish, the gold thickness should be less 0.5 mm to avoid a reduction in thermal fatigue performance.
(5) Solder mask thickness should be less than 20 μm on top of the copper circuit pattern
(6) Best solder stencil performance is achieved using laser cut stencils with electro polishing. Use of chemically etched stencils results in inferior solder paste volume control.
(7) Trace routing away from WCSP device should be balanced in X and Y directions to avoid unintentional component movement due to solder wetting forces.
TPA2025D1 land_pattern_los717.gifFigure 32. Land Pattern Dimensions

13.2 Layout Example

TPA2025D1 layoutex_slos717.gifFigure 33. TPA2025D1 Layout Example