ZHCSQ68A May   2022  – December 2022 TLIN1431-Q1

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 ESD Ratings, IEC Specification
    4. 6.4 Recommended Operating Conditions
    5. 6.5 Thermal Information
    6. 6.6 Power Supply Characteristics
    7. 6.7 Electrical Characteristics
    8. 6.8 AC Switching Characteristics
    9. 6.9 Typical Characteristics
  7. Parameter Measurement Information
    1. 7.1 Test Circuit: Diagrams and Waveforms
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  LIN (Local Interconnect Network) Bus
        1. 8.3.1.1 LIN Transmitter Characteristics
        2. 8.3.1.2 LIN Receiver Characteristics
          1. 8.3.1.2.1 Termination
      2. 8.3.2  TXD (Transmit Input and Output)
      3. 8.3.3  RXD (Receive Output)
      4. 8.3.4  WAKE (High Voltage Local Wake Up Input)
      5. 8.3.5  WDT or CLK (Pin Programmable Watchdog Delay Input or SPI Clock)
      6. 8.3.6  WDI or SDI (Watchdog Timer Input or SPI Serial Data In)
      7. 8.3.7  PIN or nCS (Pin Watchdog Select or SPI Chip Select)
      8. 8.3.8  LIMP (Limp Home Output – High Voltage Open Drain Output)
        1. 8.3.8.1 LIMP in Pin Control Mode
        2. 8.3.8.2 LIMP in SPI Control Mode
      9. 8.3.9  nWDR/SDO (Watchdog Timeout Reset Output/SPI Serial Data Out)
      10. 8.3.10 HSS (High-side Switch)
      11. 8.3.11 HSSC or FSO (High-side Switch Control or Function Output)
      12. 8.3.12 WKRQ or INH (Wake Request or Inhibit)
      13. 8.3.13 PV
      14. 8.3.14 DIV_ON
      15. 8.3.15 VBAT (Battery Voltage)
      16. 8.3.16 VSUP (Supply Voltage)
      17. 8.3.17 GND (Ground)
      18. 8.3.18 EN or nINT (Enable Input or Interrupt Output)
      19. 8.3.19 nRST (Reset Input and Reset Output)
      20. 8.3.20 VCC (Supply Output)
      21. 8.3.21 VBAT Voltage Divider
      22. 8.3.22 Protection Features
        1. 8.3.22.1  Sleep Wake Error (SWE) Timer
        2. 8.3.22.2  Device Reset
        3. 8.3.22.3  TXD Dominant Time Out (DTO)
        4. 8.3.22.4  Bus Stuck Dominant System Fault: False Wake Up Lockout
        5. 8.3.22.5  Thermal Shutdown
        6. 8.3.22.6  Under-voltage on VSUP
        7. 8.3.22.7  Unpowered Device and LIN Bus
        8. 8.3.22.8  Floating Pins
        9. 8.3.22.9  VCC Voltage Regulator
          1. 8.3.22.9.1 Under or Over Voltage and Short Circuit
          2. 8.3.22.9.2 Output Capacitance Selection
          3. 8.3.22.9.3 Low-Voltage Tracking
          4. 8.3.22.9.4 Power Supply Recommendation
        10. 8.3.22.10 Watchdog
          1. 8.3.22.10.1 Watchdog in Pin Control Mode
          2. 8.3.22.10.2 Watchdog in SPI Control Mode
          3. 8.3.22.10.3 Watchdog Error Counter
          4. 8.3.22.10.4 Pin Control Mode
          5. 8.3.22.10.5 SPI Control Programming
          6. 8.3.22.10.6 Watchdog Register Relationship
          7. 8.3.22.10.7 Watchdog Timing
      23. 8.3.23 Channel Expansion
        1. 8.3.23.1 Channel Expansion for LIN
        2. 8.3.23.2 Channel Expansion for CAN Transceiver
    4. 8.4 Device Functional Modes
      1. 8.4.1 Init Mode
      2. 8.4.2 Normal Mode
      3. 8.4.3 Fast Mode
      4. 8.4.4 Sleep Mode
      5. 8.4.5 Standby Mode
      6. 8.4.6 Restart Mode
        1. 8.4.6.1 Restart Counter
        2. 8.4.6.2 nRST Behavior in Restart Mode
      7. 8.4.7 Fail-safe Mode
      8. 8.4.8 Wake Up Events
        1. 8.4.8.1 Wake Up Request (RXD)
        2. 8.4.8.2 Local Wake Up (LWU) via WAKE Terminal
          1. 8.4.8.2.1 Static WAKE
          2. 8.4.8.2.2 Cyclic Sense Wake
      9. 8.4.9 Mode Transitions
    5. 8.5 Programming
      1. 8.5.1 SPI Communication
        1. 8.5.1.1 Cyclic Redundancy Check
        2. 8.5.1.2 Chip Select Not (nCS)
        3. 8.5.1.3 Serial Clock Input (CLK)
        4. 8.5.1.4 Serial Data Input (SDI)
        5. 8.5.1.5 Serial Data Output (SDO)
    6. 8.6 Registers
      1. 8.6.1  DEVICE_ID_y Register (Address = 0h + formula) [reset = 0h]
      2. 8.6.2  REV_ID_MAJOR Register (Address = 8h) [reset = 01h]
      3. 8.6.3  REV_ID_MINOR Register (Address = 9h) [reset = 0h]
      4. 8.6.4  CRC_CNTL Register (Address = Ah) [reset = 0h]
      5. 8.6.5  CRC_POLY_SET (Address = Bh) [reset = 00h]
      6. 8.6.6  Scratch_Pad_SPI Register (Address = Fh) [reset = 0h]
      7. 8.6.7  WAKE_PIN_CONFIG1 Register (Address = 11h) [reset = 04h]
      8. 8.6.8  WAKE_PIN_CONFIG2 Register (Address = 12h) [reset = 2h]
      9. 8.6.9  WD_CONFIG_1 Register (Address = 13h) [reset = 90h]
      10. 8.6.10 WD_CONFIG_2 Register (Address = 14h) [reset = 02h]
      11. 8.6.11 WD_INPUT_TRIG Register (Address = 15h) [reset = 0h]
      12. 8.6.12 WD_RST_PULSE Register (Address = 16h) [reset = 40h]
      13. 8.6.13 FSM_CONFIG Register (Address = 17h) [reset = 0h]
      14. 8.6.14 FSM_CNTR Register (Address = 18h) [reset = 0h]
      15. 8.6.15 DEVICE_RST Register (Address = 19h) [reset = 0h]
      16. 8.6.16 DEVICE_CONFIG (Address = 1Ah) [reset = 80h]
      17. 8.6.17 DEVICE_CONFIG2 (Address = 1Bh) [reset = 0h]
      18. 8.6.18 SWE_TIMER (Address = 1Ch) [reset = 30h]
      19. 8.6.19 LIN_CNTL (Address = 1Dh) [reset = 00h]
      20. 8.6.20 HSS_CNTL (Address = 1Eh) [reset = 0h]
      21. 8.6.21 PWM1_CNTL1 (Address = 1Fh) [reset = 0h]
      22. 8.6.22 PWM1_CNTL2 (Address = 20h) [reset = 0h]
      23. 8.6.23 PWM1_CNTL3 (Address = 21h) [reset = 00h]
      24. 8.6.24 PWM2_CNTL1 (Address = 22h) [reset = 0h]
      25. 8.6.25 PWM2_CNTL2 (Address = 23h) [reset = 0h]
      26. 8.6.26 PWM2_CNTL3 (Address = 24h) [reset = 0h]
      27. 8.6.27 TIMER1_CONFIG (Address = 25h) [reset = 00h]
      28. 8.6.28 TIMER2_CONFIG (Address = 26h) [reset = 00h]
      29. 8.6.29 RSRT_CNTR (Address = 28h) [reset = 40h]
      30. 8.6.30 nRST_CNTL (Address = 29h) [reset = 00h]
      31. 8.6.31 INT_GLOBAL Register (Address = 50h) [reset = A0h]
      32. 8.6.32 INT_1 Register (Address = 51h) [reset = 0h]
      33. 8.6.33 INT_2 Register (Address = 52h) [reset = 40h]
      34. 8.6.34 INT_3 Register (Address 53h) [reset = 0h]
      35. 8.6.35 INT_EN_1 Register (Address = 56h) [reset = B0h]
      36. 8.6.36 INT_EN_2 Register (Address = 57h) [reset = 37h]
      37. 8.6.37 INT_EN_3 Register (Address =58h) [reset = BCh]
      38. 8.6.38 INT_4 Register (Address = 5Ah) [reset = 0h]
      39. 8.6.39 INT_EN_4 Register (Address = 5Eh) [reset = CCh]
      40. 8.6.40 Reserved Registers
  9. Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Device Brownout Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Normal Mode Application Note
        2. 9.2.1.2 Standby Mode Application Note
        3. 9.2.1.3 TXD Dominant State Timeout Application Note
      2. 9.2.2 Detailed Design Procedures
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  10. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 接收文档更新通知
    3. 10.3 支持资源
    4. 10.4 商标
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 术语表
  11. 11Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • RGY|20
散热焊盘机械数据 (封装 | 引脚)
订购信息

Pin Configuration and Functions

Figure 5-1 RGY Package, 20-Pin QFN
(Top View)
Table 5-1 Pin Functions
PINTYPEDESCRIPTION
NAMENO.
VSUP1IDevice supply voltage (connected to battery in series with external reverse blocking diode)
VCC2OOutput voltage from integrated voltage regulator
nRST3I/OReset input/output (active low)
WDT/CLK4IPin control: WDT - Programmable watchdog window set input (3 levels)
SPI control: CLK - SPI clock input
nWDR/SDO5OPin control: nWDR - Watchdog failure output trigger
SPI control: SDO - SPI serial data output
WDI/SDI6IPin control: WDI - Watchdog timer trigger input active on both rising and falling edges (Must be driven at all times)
SPI control: SDI - SPI serial data input
PIN/nCS7IPin or SPI control selection pin at power up.
Pin control: does not change
SPI control: nCS - SPI chip select (active low)
EN/nINT8I/OPin control: EN - Device mode change input pin
SPI control: nINT - Device interrupt output pin
HSSC/FSO9I/OPin control: HSSC - High side switch control input pin
SPI control: FSO - Function output pin
PV10OInternal VBAT voltage divider output
DIV_ON11IInput to turn on the internal VBAT voltage divider, active high
TXD12ITXD input interface to control state of LIN output
RXD13ORXD output interface reporting state of LIN bus voltage
GND, Pad14Ground
LIN15I/OLIN bus single-wire transmitter and receiver
WKRQ/INH16ODigital output for wake or high voltage inhibit output depending upon state of pin at power up
WAKE17IHigh voltage local wake up (LWU) pin
HSS18OHigh side switch
LIMP19OUsed for LIMP home, watchdog event causes this pin to switch VSUP
VBAT20ISupply voltage divider sense input (connected to battery)