ZHCSCG5C May   2014  – November 2019 TCA9544A

PRODUCTION DATA.  

  1. 特性
  2. 应用
  3. 说明
    1.     Device Images
      1.      简化原理图
  4. 修订历史记录
  5. Pin Configuration and Functions
    1.     Pin Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Interface Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Interrupt Timing Requirements
    9. 6.9 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power-On Reset
    5. 8.5 Programming
      1. 8.5.1 I2C Interface
    6. 8.6 Control Register
      1. 8.6.1 Device Address
      2. 8.6.2 Control Register Description
      3. 8.6.3 Control Register Definition
      4. 8.6.4 Interrupt Handling
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 TCA9544A Application Curves
  10. 10Power Supply Recommendations
    1. 10.1 Power-On Reset Requirements
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12器件和文档支持
    1. 12.1 接收文档更新通知
    2. 12.2 支持资源
    3. 12.3 商标
    4. 12.4 静电放电警告
    5. 12.5 Glossary
  13. 13机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Electrical Characteristics(2)

over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS VCC MIN TYP(1) MAX UNIT
VPORR Power-on reset voltage, VCC rising No load: VI = VCC or GND 1.2 1.5 V
VPORF Power-on reset voltage, VCC falling(3) No load: VI = VCC or GND 0.8 1 V
Vpass Switch output voltage VSWin = VCC ISWout = –100 μA 5 V 3.6 V
4.5 to 5.5 V 2.6 4.5
3.3 V 1.9
3 to 3.6 V 1.6 2.8
2.5 V 1.4
2.3 to 2.7 V 1.0 1.8
1.8 V 0.8
1.65 to 1.95 V 0.5 1.1
IOH INT VO = VCC 1.65 to 5.5 V 10 μA
IOL SDA VOL = 0.4 V 1.65 to 5.5 V 3 7 mA
VOL = 0.6 V 6 10
INT VOL = 0.4 V 3
II SCL, SDA VI = VCC or GND 1.65 to 5.5 V ±1 μA
SC3–SC0, SD3–SD0 ±1
A2–A0 ±1
INT3INT0 ±1
ICC Operating mode fSCL = 400 kHz VI = VCC or GND
IO = 0
tr,max = 300 ns
5.5 V 50 μA
3.6 V 20
2.7 V 11
1.65 V 6
fSCL = 100 kHz VI = VCC or GND
IO = 0
tr,max = 1 µs
5.5 V 35
3.6 V 14
2.7 V 5
1.65 V 2
Standby mode Low inputs VI = GND IO = 0 5.5 V 1.6 2
3.6 V 1.0 1.3
2.7 V 0.7 1.1
1.65 V 0.4 0.55
High inputs VI = VCC IO = 0 5.5 V 1.6 2
3.6 V 1.0 1.3
2.7 V 0.7 1.1
1.65 V 0.4 0.55
ΔICC Supply-current change INT3INT0 One INT3INT0 input at 0.6 V,
Other inputs at VCC or GND
1.65 to 5.5 V 3 20 μA
One INT3INT0 input at VCC – 0.6 V,
Other inputs at VCC or GND
3 20
SCL, SDA SCL or SDA input at 0.6 V,
Other inputs at VCC or GND
2 15
SCL or SDA inputs at VCC – 0.6 V,
Other inputs at VCC or GND
2 15
Ci A2–A0 VI = VCC or GND 1.65 to 5.5 V 4.5 6 pF
INT3INT0 4.5 6
Cio(OFF)(4) SCL, SDA VI = VCC or GND Switch OFF 1.65 to 5.5 V 15 19 pF
SC3–SC0, SD3–SD0 6 8
RON Switch-on resistance VO = 0.4 V IO = 15 mA 4.5 to 5.5 V 10 16
3 to 3.6 V 13 20
VO = 0.4 V IO = 10 mA 2.3 to 2.7 V 16 45
1.65 to 1.95 V 25 70
All typical values are at nominal supply voltage (1.8-V, 2.5-V, 3.3-V, or 5-V VCC), TA = 25°C.
For operation between specified voltage ranges, refer to the worst-case parameter in both applicable ranges.
The power-on reset circuit resets the I2C bus logic when VCC < VPORF.
Cio(ON) depends on device capacitance and load that is downstream from the device.