ZHCSM91F May   2009  – January 2023 TCA6416A

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Interface Timing Requirements
    7. 6.7 Reset Timing Requirements
    8. 6.8 Switching Characteristics
    9. 6.9 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagrams
    3. 8.3 Feature Description
      1. 8.3.1 Voltage Translation
      2. 8.3.2 I/O Port
      3. 8.3.3 Interrupt Output ( INT)
      4. 8.3.4 Reset Input ( RESET)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power-On Reset
    5. 8.5 Programming
      1. 8.5.1 I2C Interface
    6. 8.6 Register Maps
      1. 8.6.1 Device Address
      2. 8.6.2 Control Register and Command Byte
      3. 8.6.3 Register Descriptions
      4. 8.6.4 Bus Transactions
        1. 8.6.4.1 Writes
        2. 8.6.4.2 Reads
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Minimizing ICC When I/Os Control LEDs
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
    1. 10.1 Power-On Reset Requirements
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 接收文档更新通知
    2. 12.2 支持资源
    3. 12.3 商标
    4. 12.4 静电放电警告
    5. 12.5 术语表
  13. 13Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Power-On Reset Requirements

In the event of a glitch or data corruption, TCA6416A can be reset to its default conditions by using the power-on reset feature. Power-on reset requires that the device go through a power cycle to be completely reset. This reset also happens when the device is powered on for the first time in an application.

Ramping up the device VCCP before VCCI is recommended to prevent SDA from potentially being stuck LOW.

The two types of power-on reset are shown in #SCPS0691 and #SCPS0692.

GUID-CB354911-CD7F-4C3F-93FD-11DB1A641861-low.gifFigure 10-1 VCC is Lowered Below 0.2 V or 0 V and Then Ramped up to VCC
GUID-73F0DFA9-58A1-41EB-9175-BEC8F2CDF630-low.gifFigure 10-2 VCC is Lowered Below the POR Threshold, Then Ramped Back up to VCC

Table 10-1 specifies the performance of the power-on reset feature for TCA6416A for both types of power-on reset.

Table 10-1 Recommended Supply Sequencing and Ramp Rates
PARAMETER#SCPS139781#SCPS1397812MINTYPMAXUNIT
tFTFall rateSee #SCPS06910.12000ms
tRTRise rateSee #SCPS06910.12000ms
tTRR_GNDTime to re-ramp (when VCC drops to GND)See #SCPS06911μs
tTRR_POR50Time to re-ramp (when VCC drops to VPOR_MIN – 50 mV)See #SCPS06921μs
VCC_GHLevel that VCCP can glitch down to, but not cause a functional disruption when VCCX_GW = 1 μsSee #SCPS06931.2V
tGWGlitch width that will not cause a functional disruption when VCCX_GH = 0.5 × VCCxSee #SCPS069310μs
VPORFVoltage trip point of POR on falling VCC0.7V
VPORRVoltage trip point of POR on rising VCC1.4V
TA = 25°C (unless otherwise noted).
Not tested. Specified by design.

Glitches in the power supply can also affect the power-on reset performance of this device. The glitch width (VCC_GW) and height (VCC_GH) are dependent on each other. The bypass capacitance, source impedance, and device impedance are factors that affect power-on reset performance. #SCPS0693 and Table 10-1 provide more information on how to measure these specifications.

GUID-7F23E94B-AFB1-4191-B07D-70AC5C3FF04E-low.gifFigure 10-3 Glitch Width and Glitch Height

VPOR is critical to the power-on reset. VPOR is the voltage level at which the reset condition is released and all the registers and the I2C/SMBus state machine are initialized to the default states. The value of VPOR differs based on the VCC being lowered to or from 0. #SCPS0694 and Table 10-1 provide more details on this specification.

GUID-04920E49-61C0-43BF-AF7C-CFCF3898EE5B-low.gifFigure 10-4 VPOR