SLLS877H December   2007  – March 2017 SN65HVD1780 , SN65HVD1781 , SN65HVD1782

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Device Comparison Table
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings: JEDEC
    3. 7.3 ESD Ratings: IEC
    4. 7.4 Recommended Operating Conditions
    5. 7.5 Thermal Information
    6. 7.6 Electrical Characteristics
    7. 7.7 Power Dissipation Characteristics
    8. 7.8 Switching Characteristics
    9. 7.9 Typical Characteristics
  8. Parameter Measurement Information
    1. 8.1 Equivalent Input Schematic
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 70-V Fault Protection
      2. 9.3.2 Receiver Failsafe
      3. 9.3.3 Hot-Plugging
    4. 9.4 Device Functional Modes
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
        1. 10.2.1.1 Data Rate and Bus Length
        2. 10.2.1.2 Stub Length
        3. 10.2.1.3 Bus Loading
        4. 10.2.1.4 Receiver Failsafe
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Custom Design with WEBENCH® Tools
      3. 10.2.3 Application Curve
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Custom Design with WEBENCH® Tools
      2. 13.1.2 Third-Party Products Disclaimer
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 Related Links
    4. 13.4 Receiving Notification of Documentation Updates
    5. 13.5 Community Resources
    6. 13.6 Trademarks
    7. 13.7 Electrostatic Discharge Caution
    8. 13.8 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Specifications

Absolute Maximum Ratings(1)

MIN MAX UNIT
Supply voltage, VCC –0.5 7 V
Voltage at bus pin SN65HVD1780, SN65HVD1781 A, B pins –70 70 V
SN65HVD1782 A, B pins –70 30
Input voltage at any logic pin –0.3 VCC + 0.3 V
Transient overvoltage pulse through 100 Ω per TIA-485 –70 70 V
Receiver output current –24 24 mA
Junction temperature, TJ 170 °C
Storage temperature, Tstg –55 150 °C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

ESD Ratings: JEDEC

VALUE UNIT
V(ESD) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins(1) Bus pins and GND ±16000 V
All pins ±4000
Charged device model (CDM), per JEDEC specification JESD22-C101, all pins(2) ±2000
Machine model JEDEC Standard 22, Test Method A115, all pins ±400 V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

ESD Ratings: IEC

VALUE UNIT
V(ESD) Electrostatic discharge IEC 60749-26 ESD (human body model), bus terminals and GND ±16000 V

Recommended Operating Conditions

MIN NOM MAX UNIT
VCC Supply voltage 3.15 5 5.5 V
VI Input voltage at any bus terminal (separately or common mode)(1) –7 12 V
VIH High-level input voltage (driver, driver enable, and receiver enable inputs) 2 VCC V
VIL Low-level input voltage (driver, driver enable, and receiver enable inputs) 0 0.8 V
VID Differential input voltage –12 12 V
IO Output current, driver –60 60 mA
Output current, receiver –8 8 mA
RL Differential load resistance 54 60 Ω
CL Differential load capacitance 50 pF
1/tUI Signaling rate SN65HVD1780 115 kbps
SN65HVD1781 1 Mbps
SN65HVD1782 10
TA Operating free-air temperature (See Power Dissipation Characteristics) 5-V supply –40 105 °C
3.3-V supply –40 125
TJ Junction temperature –40 150 °C
By convention, the least positive (most negative) limit is designated as minimum in this data sheet.

Thermal Information

THERMAL METRIC(1) SN65HVD178x UNIT
D (SOIC) P (PDIP)
8 PINS 8 PINS
RθJA Junction-to-ambient thermal resistance JEDEC high-K model 138 59 °C/W
JEDEC low-K model 242 128
RθJC(top) Junction-to-case (top) thermal resistance 61 61 °C/W
RθJB Junction-to-board thermal resistance 62 39 °C/W
ψJT Junction-to-top characterization parameter 3.4 17.6 °C/W
ψJB Junction-to-board characterization parameter 33.4 28.3 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance N/A N/A °C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.

Electrical Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
|VOD| Driver differential output voltage magnitude RL = 60 Ω, 4.75 V ≤ VCC 375 Ω on each output to –7 V to 12 V
Figure 6
TA < 85°C 1.5 V
TA < 125°C 1.4
RL = 54 Ω,
4.75 V ≤ VCC ≤ 5.25 V
TA < 85°C 1.7 2
TA < 125°C 1.5
RL = 54 Ω,
3.15 V ≤ VCC ≤ 3.45 V
0.8 1
RL = 100 Ω,
4.75 V ≤ VCC ≤ 5.25 V
TA < 85°C 2.2 2.5
TA < 125°C 2
Δ|VOD| Change in magnitude of driver differential output voltage RL = 54 Ω –50 0 50 mV
VOC(SS) Steady-state common-mode output voltage 1 VCC/2 3 V
ΔVOC Change in differential driver output common-mode voltage –50 0 50 mV
VOC(PP) Peak-to-peak driver common-mode output voltage Center of two 27-Ω load resistors
See Figure 7
500 mV
COD Differential output capacitance 23 pF
VIT+ Positive-going receiver differential input voltage threshold –100 –35 mV
VIT– Negative-going receiver differential input voltage threshold –180 –150 mV
VHYS Receiver differential input voltage threshold hysteresis (VIT+ – VIT–) 30 50 mV
VOH Receiver high-level output voltage IOH = –8 mA 2.4 VCC – 0.3 V
VOL Receiver low-level output voltage IOL = 8 mA TA < 85°C 0.2 0.4 V
TA < 125°C 0.5
II(LOGIC) Driver input, driver enable, and receiver enable input current –50 50 μA
IOZ Receiver output high-impedance current VO = 0 V or VCC, RE at VCC –1 1 μA
IOS Driver short-circuit output current –200 200 mA
II(BUS) Bus input current (disabled driver) VCC = 3.15 to 5.5 V or
VCC = 0 V, DE at 0 V
VI = 12 V 1780, 1781 75 100 μA
1782 400 500
VI = –7 V 1780, 1781 –60 –40
1782 –400 –300
ICC Supply current (quiescent) Driver and receiver enabled DE = VCC,
RE = GND,
no load
4 6 mA
Driver enabled, receiver disabled DE = VCC,
RE = VCC,
no load
3 5
Driver disabled, receiver enabled DE = GND,
RE = GND,
no load
2 4
Drive and receiver disabled (standby mode) DE = GND,
D = open,
RE = VCC,
no load,
TA < 85°C
0.15 1 µA
DE = GND,
D = open,
RE = VCC,
no load,
TA < 125°C
12
Supply current (dynamic) See Typical Characteristics

Power Dissipation Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MAX UNIT
PD Power dissipation VCC = 5.5 V, TJ = 150°C, RL = 300 Ω,
CL = 50 pF (driver),
CL = 15 pF (receiver)
5-V supply, unterminated(1)
290 mW
VCC = 5.5 V, TJ = 150°C, RL = 100 Ω,
CL = 50 pF (driver),
CL = 15 pF (receiver)
5-V supply, RS-422 load(1)
320
VCC = 5.5 V, TJ = 150°C, RL = 54 Ω,
CL = 50 pF (driver),
CL = 15 pF (receiver)
5-V supply, RS-485 load(1)
400
TSD Thermal-shutdown junction temperature 170 °C
Driver and receiver enabled, 50% duty cycle square-wave signal at signaling rate: 1 Mbps.

Switching Characteristics

over recommended operating conditions (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
DRIVER (SN65HVD1780)
tr, tf Driver differential output rise or fall time RL = 54 Ω,
CL = 50 pF,
See Figure 8
3.15 V < VCC < 3.45 V 0.4 1.4 1.8 µs
3.15 V < VCC < 5.5 V 0.4 1.7 2.6
tPHL, tPLH Driver propagation delay RL = 54 Ω,
CL = 50 pF,
See Figure 8
0.8 2 µs
tSK(P) Driver differential output pulse skew,
|tPHL – tPLH|
RL = 54 Ω,
CL = 50 pF,
See Figure 8
20 250 ns
tPHZ, tPLZ Driver disable time See Figure 9 and Figure 10 0.1 5 µs
tPZH, tPZL Driver enable time Receiver enabled See Figure 9 and Figure 10 0.2 3 µs
Receiver disabled See Figure 9 and Figure 10 3 12
DRIVER (SN65HVD1781)
tr, tf Driver differential output rise or fall time RL = 54 Ω, CL = 50 pF, See Figure 8 50 300 ns
tPHL, tPLH Driver propagation delay RL = 54 Ω, CL = 50 pF, See Figure 8 200 ns
tSK(P) Driver differential output pulse skew,
|tPHL – tPLH|
RL = 54 Ω, CL = 50 pF, See Figure 8 25 ns
tPHZ, tPLZ Driver disable time See Figure 9 and Figure 10 3 µs
tPZH, tPZL Driver enable time Receiver enabled See Figure 9 and Figure 10 300 ns
Receiver disabled See Figure 9 and Figure 10 10 µs
DRIVER (SN65HVD1782)
tr, tf Driver differential output rise or fall time RL = 54 Ω,
CL = 50 pF
All VCC and Temperature 50 ns
VCC > 4.5 V and
T < 105°C
16
tPHL, tPLH Driver propagation delay RL = 54 Ω,
CL = 50 pF
See Figure 8 55 ns
tSK(P) Driver differential output pulse skew,
|tPHL – tPLH|
RL = 54 Ω,
CL = 50 pF
See Figure 8 10 ns
tPHZ, tPLZ Driver disable time See Figure 9 and Figure 10 3 µs
tPZH, tPZL Driver enable time Receiver enabled See Figure 9 and Figure 10 300 ns
Receiver disabled See Figure 9 and Figure 10 9 µs
RECEIVER
tr, tf Receiver output rise or fall time CL = 15 pF,
See Figure 11
All devices 4 15 ns
tPHL, tPLH Receiver propagation delay time CL = 15 pF,
See Figure 11
SN65HVD1780,
SN65HVD1781
100 200 ns
SN65HVD1782 80
tSK(P) Receiver output pulse skew,
|tPHL – tPLH|
CL = 15 pF,
See Figure 11
SN65HVD1780,
SN65HVD1781
6 20 ns
SN65HVD1782 5
tPLZ, tPHZ Receiver disable time Driver enabled, See Figure 12 15 100 ns
tPZL(1), tPZH(1)
tPZL(2), tPZH(2)
Receiver enable time Driver enabled, See Figure 12 80 300 ns
Driver disabled, See Figure 13 3 9 μs

Typical Characteristics

SN65HVD1780 SN65HVD1781 SN65HVD1782 g001_lls877.gif Figure 1. Driver Output Current vs Supply Voltage
SN65HVD1780 SN65HVD1781 SN65HVD1782 g003_lls877.gif Figure 3. Differential Output Voltage vs Differential Load Current
SN65HVD1780 SN65HVD1781 SN65HVD1782 g005_lls877.gif Figure 5. SN65HVD1780 Differential Output Amplitude and Transition Time vs Supply Voltage
SN65HVD1780 SN65HVD1781 SN65HVD1782 g002_lls877.gif Figure 2. RMS Supply Current vs Signaling Rate
SN65HVD1780 SN65HVD1781 SN65HVD1782 risefall_lls877.gif Figure 4. SN65HVD1782 Rise or Fall Time