ZHCSNJ2D July   2006  – March 2021 PCA9554

PRODUCTION DATA  

  1. 特性
  2. 说明
  3. Revision History
  4. Description (Continued)
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 I2C Interface Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Functional Block Diagram
    2. 8.2 Device Functional Modes
      1. 8.2.1 Power-On Reset
      2. 8.2.2 I/O Port
      3. 8.2.3 Interrupt Output ( INT)
        1. 8.2.3.1 Interrupt Errata
          1.        23
          2. 8.2.3.1.1 24
          3. 8.2.3.1.2 25
    3. 8.3 Programming
      1. 8.3.1 I2C Interface
      2. 8.3.2 Register Map
        1. 8.3.2.1 Device Address
        2. 8.3.2.2 Control Register And Command Byte
        3. 8.3.2.3 Register Descriptions
        4. 8.3.2.4 Bus Transactions
          1. 8.3.2.4.1 Writes
          2. 8.3.2.4.2 Reads
  9. Application Information Disclaimer
    1. 9.1 Application Information
      1. 9.1.1 Typical Application
        1. 9.1.1.1 Design Requirements
          1. 9.1.1.1.1 Minimizing ICC When I/Os Control Leds
  10. 10Power Supply Recommendations
    1. 10.1 Power-On Reset Requirements
  11. 11Device and Documentation Support
    1. 11.1 Receiving Notification of Documentation Updates
    2. 11.2 Support Resources
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Electrical Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETERTEST CONDITIONSVCCMINTYP(1)MAXUNIT
VIKInput diode clamp voltageII = –18 mA2.3 V to 5.5 V–1.2V
VPORRPower-on reset voltage, VCC risingVI = VCC or GND, IO = 01.21.5V
VPORFPower-on reset voltage, VCC fallingVI = VCC or GND, IO = 00.751

V

VOHP-port high-level output voltage(2)IOH = –8 mA2.3 V1.8V
3 V2.6
4.5 V3.1
4.75 V4.1
IOH = –10 mA2.3 V1.7
3 V2.5
4.5 V3
4.75 V4
IOLSDAVOL = 0.4 V2.3 V to 5.5 V38mA
P port(3)VOL = 0.5 V2.3 V810
3 V814
4.5 V817
4.75 V835
VOL = 0.7 V2.3 V1013
3 V1019
4.5 V1024
4.75 V1045
INTVOL = 0.4 V2.3 V to 5.5 V310
IISCL, SDAVI = VCC or GND2.3 V to 5.5 V±1μA
A2–A0±1
IIHP portVI = VCC2.3 V to 5.5 V1μA
IILP portVI = GND2.3 V to 5.5 V–100μA
ICCOperating modeVI = VCC, IO = 0, I/O = inputs,
fscl = 400 kHz, No load
5.5 V104175μA
3.6 V5090
2.7 V2065
VI = VCC, IO = 0, I/O = inputs,
fscl = 100 kHz, No load
5.5 V60150
3.6 V1540
2.7 V820
Standby modeVI = GND, IO = 0, I/O = inputs,
fscl = 0 kHz, No load
5.5 V450700
3.6 V300600
2.7 V225500
VI = VCC, IO = 0, I/O = inputs,
fscl = 0 kHz, No load
5.5 V1.93.5
3.6 V

1.1

1.8
2.7 V11.6
ΔICCAdditional current in standby modeOne input at VCC – 0.6 V,
Other inputs at VCC or GND
2.3 V to 5.5 V1.5mA
Every LED I/O at VI = 4.3 V,
fscl = 0 kHz
5.5 V1
CiSCLVI = VCC or GND2.3 V to 5.5 V48pF
CioSDAVIO = VCC or GND2.3 V to 5.5 V5.59.5pF
P port89.5
All typical values are at nominal supply voltage (2.5-V, 3.3-V, or 5-V VCC) and TA = 25°C.
The total current sourced by all I/Os must be limited to 85 mA.
Each I/O must be externally limited to a maximum of 25 mA, and the P port (P0 to P7) must be limited to a maximum current of 200 mA.