ZHCSDQ0C March   2015  – August 2018 LP8758-B0

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 简化原理图
    1.     效率与输出电流 (VIN = 3.7V)
  5. 5 修订历史记录
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 I2C Serial Bus Timing Parameter
    7. 7.7 Switching Characteristics
    8. 7.8 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
      1. 8.1.1 Buck Information
        1. 8.1.1.1 Operating Modes
        2. 8.1.1.2 Features
        3. 8.1.1.3 Programmability
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Multi-Phase DC-DC Converters
        1. 8.3.1.1 Overview
        2. 8.3.1.2 Multi-Phase Operation and Phase Adding/Shedding
        3. 8.3.1.3 Transition Between PWM and PFM Modes
        4. 8.3.1.4 Multi-Phase Switcher Configurations
        5. 8.3.1.5 Buck Converter Load Current Measurement
        6. 8.3.1.6 Spread-Spectrum Mode
      2. 8.3.2 Power-Up
      3. 8.3.3 Regulator Control
        1. 8.3.3.1 Enabling and Disabling Regulator
        2. 8.3.3.2 Changing Output Voltage
      4. 8.3.4 Device Reset Scenarios
      5. 8.3.5 Diagnosis and Protection Features
        1. 8.3.5.1 Warnings for Diagnosis (Interrupt)
          1. 8.3.5.1.1 Output Current Limit
          2. 8.3.5.1.2 Thermal Warning
        2. 8.3.5.2 Protection (Regulator Disable)
          1. 8.3.5.2.1 Short-Circuit and Overload Protection
          2. 8.3.5.2.2 Thermal Shutdown
        3. 8.3.5.3 Fault (Power Down)
          1. 8.3.5.3.1 Undervoltage Lockout
      6. 8.3.6 Digital Signal Filtering
    4. 8.4 Device Functional Modes
      1. 8.4.1 Modes of Operation
    5. 8.5 Programming
      1. 8.5.1 I2C-Compatible Interface
        1. 8.5.1.1 Data Validity
        2. 8.5.1.2 Start and Stop Conditions
        3. 8.5.1.3 Transferring Data
        4. 8.5.1.4 I2C-Compatible Chip Address
        5. 8.5.1.5 Auto Increment Feature
    6. 8.6 Register Maps
      1. 8.6.1 Register Descriptions
        1. 8.6.1.1  DEV_REV
        2. 8.6.1.2  OTP_REV
        3. 8.6.1.3  BUCK0_CTRL1
        4. 8.6.1.4  BUCK0_CTRL2
        5. 8.6.1.5  BUCK1_CTRL2
        6. 8.6.1.6  BUCK2_CTRL2
        7. 8.6.1.7  BUCK3_CTRL2
        8. 8.6.1.8  BUCK0_VOUT
        9. 8.6.1.9  BUCK0_FLOOR_VOUT
        10. 8.6.1.10 BUCK0_DELAY
        11. 8.6.1.11 RESET
        12. 8.6.1.12 CONFIG
        13. 8.6.1.13 INT_TOP
        14. 8.6.1.14 INT_BUCK_0_1
        15. 8.6.1.15 INT_BUCK_2_3
        16. 8.6.1.16 TOP_STAT
        17. 8.6.1.17 BUCK_0_1_STAT
        18. 8.6.1.18 BUCK_2_3_STAT
        19. 8.6.1.19 TOP_MASK
        20. 8.6.1.20 BUCK_0_1_MASK
        21. 8.6.1.21 BUCK_2_3_MASK
        22. 8.6.1.22 SEL_I_LOAD
        23. 8.6.1.23 I_LOAD_2
        24. 8.6.1.24 I_LOAD_1
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Application Components
          1. 9.2.2.1.1 Inductor Selection
          2. 9.2.2.1.2 Input Capacitor Selection
          3. 9.2.2.1.3 Output Capacitor Selection
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12器件和文档支持
    1. 12.1 器件支持
      1. 12.1.1 第三方产品免责声明
    2. 12.2 文档支持
      1. 12.2.1 相关文档
    3. 12.3 接收文档更新通知
    4. 12.4 社区资源
    5. 12.5 商标
    6. 12.6 静电放电警告
    7. 12.7 术语表
  13. 13机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.3.5 Diagnosis and Protection Features

The LP8758 is capable of providing three levels of protection features:

  • Warnings for diagnosis which sets interrupt;
  • Protection events which are disabling the regulator; and
  • Faults which are causing the device to shutdown.
When the device detects warning/protection condition(s), the LP8758 sets the flag bits indicating what protection or warning conditions have occurred, and the nINT pin will be pulled low. nINT will be released again after a clear of flags is complete. The nINT signal stays low until all the pending interrupts are cleared.

When a fault is detected, it is indicated by a INT_TOP.RESET_REG interrupt flag after next start-up.

Table 2. Summary of Interrupt Signals

EVENT RESULT INTERRUPT REGISTER AND BIT INTERRUPT MASK STATUS BIT RECOVERY / INTERRUPT CLEAR
Current limit triggered (20 µs debounce) No effect INT_TOP.INT_BUCKx = 1
INT_BUCKx.BUCKx_ILIM_INT = 1		 BUCKx_MASK.BUCKx_ILIM_MASK BUCKx_STAT.BUCKx_ILIM_STAT Write 1 to INT_BUCKx.BUCKx_ILIM_INT bit
Interrupt is not cleared if current limit is active
Short circuit (VOUT < 0.35 V at 1 ms after enable) or Overload (VOUT decreasing below 0.35V during operation, 1 ms debounce) Regulator disable INT_TOP.INT_BUCK0 = 1
INT_BUCK_0_1.BUCK0_SC_INT = 1		 N/A N/A Write 1 to INT_BUCK_0_1.BUCK0_SC_INT bit
Thermal Warning No effect INT_TOP.TDIE_WARN = 1 TOP_MASK.TDIE_WARN_MASK TOP_STAT.TDIE_WARN_STAT Write 1 to INT_TOP.TDIE_WARN bit
Interrupt is not cleared if temperature is above thermal warning level
Thermal Shutdown Regulator disabled INT_TOP.TDIE_SD = 1 N/A TOP_STAT.TDIE_SD_STAT Write 1 to INT_TOP.TDIE_SD bit
Interrupt is not cleared if temperature is above thermal shutdown level
Powergood, output voltage reaches the programmed value No effect INT_TOP.INT_BUCK0 = 1
INT_BUCK_0_1.BUCK0_PG_INT = 1		 BUCK_0_1_MASK.BUCK0_PG_MASK BUCK_0_1_STAT.BUCK0_PG_STAT Write 1 to INT_BUCK_0_1.BUCK0_PG_INT bit
Load current measurement ready No effect INT_TOP.I_LOAD_READY = 1 TOP_MASK.I_LOAD_READY_MASK N/A Write 1 to INT_TOP.I_LOAD_READY bit
Start-up (NRST rising edge) Device ready for operation, registers reset to default values INT_TOP.RESET_REG = 1 TOP_MASK.RESET_REG_MASK N/A Write 1 to INT_TOP.RESET_REG bit
Glitch on supply voltage and UVLO triggered (VANA falling and rising) Immediate shutdown followed by powerup, registers reset to default values INT_TOP.RESET_REG = 1 TOP_MASK.RESET_REG_MASK N/A Write 1 to INT_TOP.RESET_REG bit
Software requested reset Immediate shutdown followed by powerup, registers reset to default values INT_TOP.RESET_REG = 1 TOP_MASK.RESET_REG_MASK N/A Write 1 to INT_TOP.RESET_REG bit