ZHCSGU2A July   2017  – September 2017 LP5569

PRODUCTION DATA.  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 修订历史记录
  5. 5 Device Comparison Table
  6. 6 Pin Configuration and Functions
  7. 7 Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics
    6. 7.6  Charge-Pump Electrical Characteristics
    7. 7.7  LED Current Sinks Electrical Characteristics
    8. 7.8  Logic Interface Characteristics
    9. 7.9  Timing Requirements (EN/PWM)
    10. 7.10 Serial-Bus Timing Requirements (SDA, SCL), See
    11. 7.11 External Clock Timing Requirements (CLK), See
    12. 7.12 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
      1. 8.1.1 Programming
      2. 8.1.2 Energy Efficiency
      3. 8.1.3 Protection Features
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Current Sinks
        1. 8.3.1.1 Overview
        2. 8.3.1.2 Controlling the Low-Side Current Sinks
          1. 8.3.1.2.1 Direct Register Control
          2. 8.3.1.2.2 Controlling by Program Execution Engines
          3. 8.3.1.2.3 Master Fader Control
            1. 8.3.1.2.3.1 PWM Master Fader on EN/PWM Pin
            2. 8.3.1.2.3.2 PWM Master Fader Resolution and Input Frequency Range
            3. 8.3.1.2.3.3 PWM Master Fader Hysteresis
          4. 8.3.1.2.4 EN/PWM Input Timeout
      2. 8.3.2 Charge Pump
        1. 8.3.2.1 Overview
        2. 8.3.2.2 Pre-Regulation
        3. 8.3.2.3 Input Current Limit
        4. 8.3.2.4 Output Discharge
        5. 8.3.2.5 Controlling the Charge Pump
        6. 8.3.2.6 LED Forward Voltage Monitoring
      3. 8.3.3 Energy Efficiency
        1. 8.3.3.1 LED Powering
      4. 8.3.4 Automatic Power-Save Mode
      5. 8.3.5 Protection Features
        1. 8.3.5.1 Thermal Shutdown (TSD)
        2. 8.3.5.2 Undervoltage Lockout (UVLO)
        3. 8.3.5.3 Power-On Reset (POR)
        4. 8.3.5.4 LED Fault Detection
          1. 8.3.5.4.1 Open LED
          2. 8.3.5.4.2 Shorted LED
      6. 8.3.6 Clock Generation and Synchronization
      7. 8.3.7 GPIO/TRIG/INT Multifunctional I/O
    4. 8.4 Device Functional Modes
      1. 8.4.1 Modes Of Operation
    5. 8.5 Programming
      1. 8.5.1 I2C Interface
        1. 8.5.1.1 Data Validity
        2. 8.5.1.2 Start and Stop Conditions
        3. 8.5.1.3 Transferring Data
        4. 8.5.1.4 I2C Slave Addressing
        5. 8.5.1.5 Control Register Write Cycle
        6. 8.5.1.6 Control Register Read Cycle
        7. 8.5.1.7 Auto-Increment Feature
      2. 8.5.2 Execution Engine Programming
        1. 8.5.2.1 SRAM Memory
        2. 8.5.2.2 Variables
        3. 8.5.2.3 Instruction Set
        4. 8.5.2.4 LED Driver Instructions
          1. 8.5.2.4.1 Ramp
          2. 8.5.2.4.2 Ramp Instruction Application Example
          3. 8.5.2.4.3 Set_PWM
          4. 8.5.2.4.4 Wait
        5. 8.5.2.5 LED Mapping Instructions
          1. 8.5.2.5.1  LOAD_START and LOAD_END
          2. 8.5.2.5.2  MAP_START
          3. 8.5.2.5.3  MAP_SEL
          4. 8.5.2.5.4  MAP_CLR
          5. 8.5.2.5.5  MAP_NEXT
          6. 8.5.2.5.6  LOAD_NEXT
          7. 8.5.2.5.7  MAP_PREV
          8. 8.5.2.5.8  LOAD_PREV
          9. 8.5.2.5.9  MAP_ADDR
          10. 8.5.2.5.10 LOAD_ADDR
        6. 8.5.2.6 Branch Instructions
          1. 8.5.2.6.1 BRANCH
          2. 8.5.2.6.2 INT
          3. 8.5.2.6.3 RST
          4. 8.5.2.6.4 END
          5. 8.5.2.6.5 TRIGGER and TRIG_CLEAR
          6. 8.5.2.6.6 JNE, JGE, JL, and JE
        7. 8.5.2.7 Data Transfer and Arithmetic Instructions
          1. 8.5.2.7.1 LD
          2. 8.5.2.7.2 ADD
          3. 8.5.2.7.3 SUB
    6. 8.6 Register Maps
      1. 8.6.1 LP5569_MAP Registers
        1. 8.6.1.1  CONFIG Register (Address = 0h) [reset = 0h]
        2. 8.6.1.2  LED_ENGINE_CONTROL1 Register (Address = 1h) [reset = 0h]
        3. 8.6.1.3  LED_ENGINE_CONTROL2 Register (Address = 2h) [reset = 0h]
        4. 8.6.1.4  LED0_CONTROL Register (Address = 7h) [reset = 0h]
        5. 8.6.1.5  LED1_CONTROL Register (Address = 8h) [reset = 0h]
        6. 8.6.1.6  LED2_CONTROL Register (Address = 9h) [reset = 0h]
        7. 8.6.1.7  LED3_CONTROL Register (Address = Ah) [reset = 0h]
        8. 8.6.1.8  LED4_CONTROL Register (Address = Bh) [reset = 0h]
        9. 8.6.1.9  LED5_CONTROL Register (Address = Ch) [reset = 0h]
        10. 8.6.1.10 LED6_CONTROL Register (Address = Dh) [reset = 0h]
        11. 8.6.1.11 LED7_CONTROL Register (Address = Eh) [reset = 0h]
        12. 8.6.1.12 LED8_CONTROL Register (Address = Fh) [reset = 0h]
        13. 8.6.1.13 LED0_PWM Register (Address = 16h) [reset = 0h]
        14. 8.6.1.14 LED1_PWM Register (Address = 17h) [reset = 0h]
        15. 8.6.1.15 LED2_PWM Register (Address = 18h) [reset = 0h]
        16. 8.6.1.16 LED3_PWM Register (Address = 19h) [reset = 0h]
        17. 8.6.1.17 LED4_PWM Register (Address = 1Ah) [reset = 0h]
        18. 8.6.1.18 LED5_PWM Register (Address = 1Bh) [reset = 0h]
        19. 8.6.1.19 LED6_PWM Register (Address = 1Ch) [reset = 0h]
        20. 8.6.1.20 LED7_PWM Register (Address = 1Dh) [reset = 0h]
        21. 8.6.1.21 LED8_PWM Register (Address = 1Eh) [reset = 0h]
        22. 8.6.1.22 LED0_CURRENT Register (Address = 22h) [reset = AFh]
        23. 8.6.1.23 LED1_CURRENT Register (Address = 23h) [reset = AFh]
        24. 8.6.1.24 LED2_CURRENT Register (Address = 24h) [reset = AFh]
        25. 8.6.1.25 LED3_CURRENT Register (Address = 25h) [reset = AFh]
        26. 8.6.1.26 LED4_CURRENT Register (Address = 26h) [reset = AFh]
        27. 8.6.1.27 LED5_CURRENT Register (Address = 27h) [reset = AFh]
        28. 8.6.1.28 LED6_CURRENT Register (Address = 28h) [reset = AFh]
        29. 8.6.1.29 LED7_CURRENT Register (Address = 29h) [reset = AFh]
        30. 8.6.1.30 LED8_CURRENT Register (Address = 2Ah) [reset = AFh]
        31. 8.6.1.31 MISC Register (Address = 2Fh) [reset = 40h]
        32. 8.6.1.32 ENGINE1_PC Register (Address = 30h) [reset = 0h]
        33. 8.6.1.33 ENGINE2_PC Register (Address = 31h) [reset = 0h]
        34. 8.6.1.34 ENGINE3_PC Register (Address = 32h) [reset = 0h]
        35. 8.6.1.35 MISC2 Register (Address = 33h) [reset = 2h]
        36. 8.6.1.36 ENGINE_STATUS Register (Address = 3Ch) [reset = 80h]
        37. 8.6.1.37 IO_CONTROL Register (Address = 3Dh) [reset = 2h]
        38. 8.6.1.38 VARIABLE_D Register (Address = 3Eh) [reset = 0h]
        39. 8.6.1.39 RESET Register (Address = 3Fh) [reset = 0h]
        40. 8.6.1.40 ENGINE1_VARIABLE_A Register (Address = 42h) [reset = 0h]
        41. 8.6.1.41 ENGINE2_VARIABLE_A Register (Address = 43h) [reset = 0h]
        42. 8.6.1.42 ENGINE3_VARIABLE_A Register (Address = 44h) [reset = 0h]
        43. 8.6.1.43 MASTER_FADER1 Register (Address = 46h) [reset = 0h]
        44. 8.6.1.44 MASTER_FADER2 Register (Address = 47h) [reset = 0h]
        45. 8.6.1.45 MASTER_FADER3 Register (Address = 48h) [reset = 0h]
        46. 8.6.1.46 MASTER_FADER_PWM Register (Address = 4Ah) [reset = 0h]
        47. 8.6.1.47 ENGINE1_PROG_START Register (Address = 4Bh) [reset = 0h]
        48. 8.6.1.48 ENGINE2_PROG_START Register (Address = 4Ch) [reset = 0h]
        49. 8.6.1.49 ENGINE3_PROG_START Register (Address = 4Dh) [reset = 0h]
        50. 8.6.1.50 PROG_MEM_PAGE_SELECT Register (Address = 4Fh) [reset = 0h]
        51. 8.6.1.51 PROGRAM_MEM_00 Register (Address = 50h) [reset = 0h]
        52. 8.6.1.52 PROGRAM_MEM_01 Register (Address = 51h) [reset = 0h]
        53. 8.6.1.53 PROGRAM_MEM_02 Register (Address = 52h) [reset = 0h]
        54. 8.6.1.54 PROGRAM_MEM_03 Register (Address = 53h) [reset = 0h]
        55. 8.6.1.55 PROGRAM_MEM_04 Register (Address = 54h) [reset = 0h]
        56. 8.6.1.56 PROGRAM_MEM_05 Register (Address = 55h) [reset = 0h]
        57. 8.6.1.57 PROGRAM_MEM_06 Register (Address = 56h) [reset = 0h]
        58. 8.6.1.58 PROGRAM_MEM_07 Register (Address = 57h) [reset = 0h]
        59. 8.6.1.59 PROGRAM_MEM_08 Register (Address = 58h) [reset = 0h]
        60. 8.6.1.60 PROGRAM_MEM_09 Register (Address = 59h) [reset = 0h]
        61. 8.6.1.61 PROGRAM_MEM_10 Register (Address = 5Ah) [reset = 0h]
        62. 8.6.1.62 PROGRAM_MEM_11 Register (Address = 5Bh) [reset = 0h]
        63. 8.6.1.63 PROGRAM_MEM_12 Register (Address = 5Ch) [reset = 0h]
        64. 8.6.1.64 PROGRAM_MEM_13 Register (Address = 5Dh) [reset = 0h]
        65. 8.6.1.65 PROGRAM_MEM_14 Register (Address = 5Eh) [reset = 0h]
        66. 8.6.1.66 PROGRAM_MEM_15 Register (Address = 5Fh) [reset = 0h]
        67. 8.6.1.67 PROGRAM_MEM_16 Register (Address = 60h) [reset = 0h]
        68. 8.6.1.68 PROGRAM_MEM_17 Register (Address = 61h) [reset = 0h]
        69. 8.6.1.69 PROGRAM_MEM_18 Register (Address = 62h) [reset = 0h]
        70. 8.6.1.70 PROGRAM_MEM_19 Register (Address = 63h) [reset = 0h]
        71. 8.6.1.71 PROGRAM_MEM_20 Register (Address = 64h) [reset = 0h]
        72. 8.6.1.72 PROGRAM_MEM_21 Register (Address = 65h) [reset = 0h]
        73. 8.6.1.73 PROGRAM_MEM_22 Register (Address = 66h) [reset = 0h]
        74. 8.6.1.74 PROGRAM_MEM_23 Register (Address = 67h) [reset = 0h]
        75. 8.6.1.75 PROGRAM_MEM_24 Register (Address = 68h) [reset = 0h]
        76. 8.6.1.76 PROGRAM_MEM_25 Register (Address = 69h) [reset = 0h]
        77. 8.6.1.77 PROGRAM_MEM_26 Register (Address = 6Ah) [reset = 0h]
        78. 8.6.1.78 PROGRAM_MEM_27 Register (Address = 6Bh) [reset = 0h]
        79. 8.6.1.79 PROGRAM_MEM_28 Register (Address = 6Ch) [reset = 0h]
        80. 8.6.1.80 PROGRAM_MEM_29 Register (Address = 6Dh) [reset = 0h]
        81. 8.6.1.81 PROGRAM_MEM_30 Register (Address = 6Eh) [reset = 0h]
        82. 8.6.1.82 PROGRAM_MEM_31 Register (Address = 6Fh) [reset = 0h]
        83. 8.6.1.83 ENGINE1_MAPPING1 Register (Address = 70h) [reset = 0h]
        84. 8.6.1.84 ENGINE1_MAPPING2 Register (Address = 71h) [reset = 0h]
        85. 8.6.1.85 ENGINE2_MAPPING1 Register (Address = 72h) [reset = 0h]
        86. 8.6.1.86 ENGINE2_MAPPING2 Register (Address = 73h) [reset = 0h]
        87. 8.6.1.87 ENGINE3_MAPPING1 Register (Address = 74h) [reset = 0h]
        88. 8.6.1.88 ENGINE3_MAPPING2 Register (Address = 75h) [reset = 0h]
        89. 8.6.1.89 PWM_CONFIG Register (Address = 80h) [reset = 4h]
        90. 8.6.1.90 LED_FAULT1 Register (Address = 81h) [reset = 0h]
        91. 8.6.1.91 LED_FAULT2 Register (Address = 82h) [reset = 0h]
        92. 8.6.1.92 GENERAL_FAULT Register (Address = 83h) [reset = 4h]
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Single LP5569 Application
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
        3. 9.2.1.3 Application Curves
      2. 9.2.2 Using Multiple LP5569 Devices
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
        3. 9.2.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Flying Capacitor Placement
      2. 11.1.2 Output Capacitor Placement
      3. 11.1.3 Input Capacitor Placement
    2. 11.2 Layout Example
  12. 12器件和文档支持
    1. 12.1 器件支持
      1. 12.1.1 Third-Party Products Disclaimer
    2. 12.2 接收文档更新通知
    3. 12.3 社区资源
    4. 12.4 商标
    5. 12.5 静电放电警告
    6. 12.6 Glossary
  13. 13机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

12 器件和文档支持

12.1 器件支持

12.1.1 Third-Party Products Disclaimer

TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.

12.2 接收文档更新通知

要接收文档更新通知，请导航至 TI.com 上的器件产品文件夹。单击右上角的通知我 进行注册，即可每周接收产品信息更改摘要。有关更改的详细信息，请查看任何已修订文档中包含的修订历史记录。

12.3 社区资源

下列链接提供到 TI 社区资源的连接。链接的内容由各个分销商“按照原样”提供。这些内容并不构成 TI 技术规范，并且不一定反映 TI 的观点；请参阅 TI 的 《使用条款》。

    TI E2E™ 在线社区 TI 的工程师对工程师 (E2E) 社区。此社区的创建目的在于促进工程师之间的协作。在 e2e.ti.com 中，您可以咨询问题、分享知识、拓展思路并与同行工程师一道帮助解决问题。
    设计支持 TI 参考设计支持 可帮助您快速查找有帮助的 E2E 论坛、设计支持工具以及技术支持的联系信息。

12.4 商标

E2E is a trademark of Texas Instruments.

蓝牙 is a registered trademark of Bluetooth SIG, Inc..

All other trademarks are the property of their respective owners.

12.5 静电放电警告

esds-image

这些装置包含有限的内置 ESD 保护。 存储或装卸时，应将导线一起截短或将装置放置于导电泡棉中，以防止 MOS 门极遭受静电损伤。

12.6 Glossary

SLYZ022 — TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.