SLCS144E July   2004  – October 2014 LM317L

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
  4. Simplified Schematic
  5. Revision History
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 Handling Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 NPN Darlington Output Drive
      2. 8.3.2 Overload Block
      3. 8.3.3 Programmable Feedback
    4. 8.4 Device Functional Modes
      1. 8.4.1 Normal operation
      2. 8.4.2 Operation With Low Input Voltage
      3. 8.4.3 Operation at Light Loads
      4. 8.4.4 Operation In Self Protection
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Input Capacitor
        2. 9.2.2.2 Output Capacitor
        3. 9.2.2.3 Feedback Resistors
        4. 9.2.2.4 Adjustment Terminal Capacitor
        5. 9.2.2.5 Design Options and Parameters
        6. 9.2.2.6 Output Voltage
        7. 9.2.2.7 Ripple Rejection
        8. 9.2.2.8 Input Short Protection
      3. 9.2.3 Application Curves
    3. 9.3 General Configurations
      1. 9.3.1 Regulator Circuit With Improved Ripple Rejection
      2. 9.3.2 0-V to 30-V Regulator Circuit
      3. 9.3.3 Precision Current-Limiter Circuit
      4. 9.3.4 Tracking Preregulator Circuit
      5. 9.3.5 Slow-Turn On 15-V Regulator Circuit
      6. 9.3.6 50-mA Constant-Current Battery-Charger Circuit
      7. 9.3.7 Current-Limited 6-V Charger
      8. 9.3.8 High-Current Adjustable Regulator
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Trademarks
    2. 12.2 Electrostatic Discharge Caution
    3. 12.3 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • D|8
  • PW|8
  • PK|3
  • LP|3
散热焊盘机械数据 (封装 | 引脚)
订购信息

9 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality.

9.1 Application Information

The two output resistors are the only components required to adjust VOUT.

9.2 Typical Application

appin1_lcs144.gif

9.2.1 Design Requirements

  1. Use of an input bypass capacitor is recommended if regulator is far from the filter capacitors.
  2. For this design example, use the parameters listed in Table 1.
  3. Use of an output capacitor improves transient response, but is optional.

Table 1. Design Parameters

DESIGN PARAMETER EXAMPLE VALUE
Input voltage range (Output Voltage + 2.5 V) to 32 V
Output voltage VREF × (1 + R2 / R1) + IADJ × R2

9.2.2 Detailed Design Procedure

9.2.2.1 Input Capacitor

An input capacitor is not required, but it is recommended, particularly if the regulator is not in close proximity to the power-supply filter capacitors. A 0.1-µF ceramic or 1-µF tantalum provides sufficient bypassing for most applications, especially when adjustment and output capacitors are used.

9.2.2.2 Output Capacitor

An output capacitor improves transient response, but it not needed for stability.

9.2.2.3 Feedback Resistors

The feedback resistor set the output voltage using Equation 2.

Equation 2. VREF × (1 + R2 / R1) + IADJ × R2

9.2.2.4 Adjustment Terminal Capacitor

The optional adjustment pin capacitor will improve ripple rejection by preventing the amplification of the ripple. When capacitor is used and VOUT > 6 V, a protection diode from adjust to output is recommended.

9.2.2.5 Design Options and Parameters

Common Linear Regulator designs are concerned with the following parameters:

  • Input voltage range
  • Input capacitor range
  • Output voltage
  • Output current rating
  • Output capacitor range
  • Input short protection
  • Stability
  • Ripple rejection

9.2.2.6 Output Voltage

VO is calculated as shown in Equation 3.

Equation 3. lm317l_appeqn_01.gif

Because IADJ typically is 50 µA, it is negligible in most applications.

9.2.2.7 Ripple Rejection

CADJ is used to improve ripple rejection; it prevents amplification of the ripple as the output voltage is adjusted higher. If CADJ is used, it is best to include protection diodes.

9.2.2.8 Input Short Protection

If the input is shorted to ground during a fault condition, protection diodes provide measures to prevent the possibility of external capacitors discharging through low-impedance paths in the IC. By providing low-impedance discharge paths for CO and CADJ, respectively, D1 and D2 prevent the capacitors from discharging into the output of the regulator.

9.2.3 Application Curves

lm317lrefcurve.gifFigure 2. Adjustment Voltage Relative to Output Over Temperature

9.3 General Configurations

9.3.1 Regulator Circuit With Improved Ripple Rejection

C2 helps to stabilize the voltage at the adjustment pin, which will help reject noise. Diode D1 exists to discharge C2 in case the output is shorted to ground.

appin3_lcs144.gifFigure 3. Regulator Circuit With Improved Ripple Rejection

9.3.2 0-V to 30-V Regulator Circuit

In the 0-V to 30-V regulator circuit application, the output voltage is determined by Equation 4.

Equation 4. lm317l_appeqn.gif
appin2_lcs144.gifFigure 4. 0-V to 30-V Regulator Circuit

9.3.3 Precision Current-Limiter Circuit

This application will limit the output current to the ILIMIT shown in Figure 5.

appin4_lcs144.gifFigure 5. Precision Current-Limiter Circuit

9.3.4 Tracking Preregulator Circuit

The tracking preregulator circuit application keeps a constant voltage across the second LM317L in the circuit.

appin5_lcs144.gifFigure 6. Tracking Preregulator Circuit

9.3.5 Slow-Turn On 15-V Regulator Circuit

The capacitor C1, in combination with the PNP transistor, helps the circuit to slowly start supplying voltage. In the beginning, the capacitor is not charged. Therefore, output voltage will start at 1.9 V, as determined by Equation 5. As the capacitor voltage rises, VOUT will rise at the same rate. When the output voltage reaches the value determined by R1 and R2, the PNP will be turned off.

Equation 5. VC1 + VBE + 1.25 V = 0 V + 0.65 V + 1.25 V = 1.9 V
appin6_lcs144.gifFigure 7. Slow-Turn On 15-V Regulator Circuit

9.3.6 50-mA Constant-Current Battery-Charger Circuit

The current-limit operation mode can be used to trickle charge a battery at a fixed current as determined by Equation 6. VI should be greater than VBAT + 3.75 V.

Equation 6. ICHG = 1.25 V ÷ 24 Ω
Equation 7. (1.25 V [VREF] + 2.5 V [headroom])
appin8_lcs144.gifFigure 8. 50-mA Constant-Current Battery-Charger Circuit

9.3.7 Current-Limited 6-V Charger

As the charge current increases, the voltage at the bottom resistor increases until the NPN starts sinking current from the adjustment pin. The voltage at the adjustment pin will drop, and consequently the output voltage will decrease until the NPN stops conducting.

appin8a_lcs144.gifFigure 9. Current-Limited 6-V Charger

9.3.8 High-Current Adjustable Regulator

This application allows higher currents at VOUT than the LM317L device can provide, while still keeping the output voltage at levels determined by the adjustment-pin resistor divider of the LM317L.

appin9_lcs144.gifFigure 10. High-Current Adjustable Regulator