ZHCSNB8A February   2021  – January 2024 BQ25730

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 说明（续）
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics(BQ25730)
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Power-Up Sequence
      2. 8.3.2  Two-Level Battery Discharge Current Limit
      3. 8.3.3  Fast Role Swap Feature
      4. 8.3.4  CHRG_OK Indicator
      5. 8.3.5  Input and Charge Current Sensing
      6. 8.3.6  Input Voltage and Current Limit Setup
      7. 8.3.7  Battery Cell Configuration
      8. 8.3.8  Device HIZ State
      9. 8.3.9  USB On-The-Go (OTG)
      10. 8.3.10 Converter Operation
      11. 8.3.11 Inductance Detection Through IADPT Pin
      12. 8.3.12 Converter Compensation
      13. 8.3.13 Continuous Conduction Mode (CCM)
      14. 8.3.14 Pulse Frequency Modulation (PFM)
      15. 8.3.15 Switching Frequency and Dithering Feature
      16. 8.3.16 Current and Power Monitor
        1. 8.3.16.1 High-Accuracy Current Sense Amplifier (IADPT and IBAT)
        2. 8.3.16.2 High-Accuracy Power Sense Amplifier (PSYS)
      17. 8.3.17 Input Source Dynamic Power Management
      18. 8.3.18 Input Current Optimizer (ICO)
      19. 8.3.19 Two-Level Adapter Current Limit (Peak Power Mode)
      20. 8.3.20 Processor Hot Indication
        1. 8.3.20.1 PROCHOT During Low Power Mode
        2. 8.3.20.2 PROCHOT Status
      21. 8.3.21 Device Protection
        1. 8.3.21.1 Watchdog Timer
        2. 8.3.21.2 Input Overvoltage Protection (ACOV)
        3. 8.3.21.3 Input Overcurrent Protection (ACOC)
        4. 8.3.21.4 System Overvoltage Protection (SYSOVP)
        5. 8.3.21.5 Battery Overvoltage Protection (BATOVP)
        6. 8.3.21.6 Battery Discharge Overcurrent Protection (BATOC)
        7. 8.3.21.7 Battery Short Protection (BATSP)
        8. 8.3.21.8 System Undervoltage Lockout (VSYS_UVP) and Hiccup Mode
        9. 8.3.21.9 Thermal Shutdown (TSHUT)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Forward Mode
        1. 8.4.1.1 System Voltage Regulation with Narrow VDC Architecture
        2. 8.4.1.2 Battery Charging
      2. 8.4.2 USB On-The-Go
      3. 8.4.3 Pass Through Mode (PTM)-Patented Technology
    5. 8.5 Programming
      1. 8.5.1 I2C Serial Interface
        1. 8.5.1.1 Timing Diagrams
        2. 8.5.1.2 Data Validity
        3. 8.5.1.3 START and STOP Conditions
        4. 8.5.1.4 Byte Format
        5. 8.5.1.5 Acknowledge (ACK) and Not Acknowledge (NACK)
        6. 8.5.1.6 Target Address and Data Direction Bit
        7. 8.5.1.7 Single Read and Write
        8. 8.5.1.8 Multi-Read and Multi-Write
        9. 8.5.1.9 Write 2-Byte I2C Commands
    6. 8.6 Register Map
      1. 8.6.1  ChargeOption0 Register (I2C address = 01/00h) [reset = E70Eh]
      2. 8.6.2  ChargeCurrent Register (I2C address = 03/02h) [reset = 0000h]
        1. 8.6.2.1 Battery Pre-Charge Current Clamp
      3. 8.6.3  ChargeVoltage Register (I2C address = 05/04h) [reset value based on CELL_BATPRESZ pin setting]
      4. 8.6.4  ChargerStatus Register (I2C address = 21/20h) [reset = 0000h]
      5. 8.6.5  ProchotStatus Register (I2C address = 23/22h) [reset = B800h]
      6. 8.6.6  IIN_DPM Register (I2C address = 25/24h) [reset = 4100h]
      7. 8.6.7  ADCVBUS/PSYS Register (I2C address = 27/26h)
      8. 8.6.8  ADCIBAT Register (I2C address = 29/28h)
      9. 8.6.9  ADCIIN/CMPIN Register (I2C address = 2B/2Ah)
      10. 8.6.10 ADCVSYS/VBAT Register (I2C address = 2D/2Ch)
      11. 8.6.11 ChargeOption1 Register (I2C address = 31/30h) [reset = 3F00h]
      12. 8.6.12 ChargeOption2 Register (I2C address = 33/32h) [reset = 00B7]
      13. 8.6.13 ChargeOption3 Register (I2C address = 35/34h) [reset = 0434h]
      14. 8.6.14 ProchotOption0 Register (I2C address = 37/36h) [reset = 4A81h(2S~5s) 4A09(1S)]
      15. 8.6.15 ProchotOption1 Register (I2C address = 39/38h) [reset = 41A0h]
      16. 8.6.16 ADCOption Register (I2C address = 3B/3Ah) [reset = 2000h]
      17. 8.6.17 ChargeOption4 Register (I2C address = 3D/3Ch) [reset = 0048h]
      18. 8.6.18 Vmin Active Protection Register (I2C address = 3F/3Eh) [reset = 006Ch(2s~5s)/0004h(1S)]
      19. 8.6.19 OTGVoltage Register (I2C address = 07/06h) [reset = 09C4h]
      20. 8.6.20 OTGCurrent Register (I2C address = 09/08h) [reset = 3C00h]
      21. 8.6.21 InputVoltage(VINDPM) Register (I2C address = 0B/0Ah) [reset =VBUS-1.28V]
      22. 8.6.22 VSYS_MIN Register (I2C address = 0D/0Ch) [reset value based on CELL_BATPRESZ pin setting]
      23. 8.6.23 IIN_HOST Register (I2C address = 0F/0Eh) [reset = 2000h]
      24. 8.6.24 ID Registers
        1. 8.6.24.1 ManufactureID Register (I2C address = 2Eh) [reset = 40h]
        2. 8.6.24.2 Device ID (DeviceAddress) Register (I2C address = 2Fh) [reset = D5h]
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Input Snubber and Filter for Voltage Spike Damping
        2. 9.2.2.2 ACP-ACN Input Filter
        3. 9.2.2.3 Inductor Selection
        4. 9.2.2.4 Input Capacitor
        5. 9.2.2.5 Output Capacitor
        6. 9.2.2.6 Power MOSFETs Selection
      3. 9.2.3 Application Curves
  11. 10Power Supply Recommendations
  12. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
      1. 11.2.1 Layout Example Reference Top View
      2. 11.2.2 Inner Layer Layout and Routing Example
  13. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 第三方产品免责声明
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 接收文档更新通知
    4. 12.4 支持资源
    5. 12.5 Trademarks
    6. 12.6 静电放电警告
    7. 12.7 术语表
  14. 13Revision History
  15. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

8.6.2 ChargeCurrent Register (I2C address = 03/02h) [reset = 0000h]

To set the charge current, write 16-bit ChargeCurrent() command (REG0x03/02h()) using the data format listed Figure 8-17.

With 5-mΩ sense resistor, the charger provides charge current range of 0 A to 16.256 A, with a 128-mA step resolution. With 10-mΩ sense resistor, the charger provides charge current range of 0 A to 8.128 A, with a 64-mA step resolution.

Upon POR, ChargeCurrent() is 0 A. Below scenarios will also reset Charge current to zero:

  • CELL_BATPRESZ going LOW (battery removal).
  • STAT_AC is not valid(Adapter removal).
  • RESET_REG is asserted and reset all registers.
  • Charge voltage is written to be 0 V.
  • Watch dog event is triggered.

Charge current is not reset in force converter latch off fault (REG0x20[2]), and ACOC/TSHUT/SYSOVP/ACOV/VSYS_UVP/BATOVP/BATOC faults.

Figure 8-17 ChargeCurrent Register (I2C address = 03/02h) [reset = 0000h]
7 6 5 4 3 2 1 0
Reserved Charge Current, bit 6 Charge Current, bit 5 Charge Current, bit 4 Charge Current, bit 3 Charge Current, bit 2
R/W R/W R/W R/W R/W R/W
7 6 5 4 3 2 1 0
Charge Current, bit 1 Charge Current, bit 0 Reserved Reserved
R/W R/W R/W R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 8-10 Charge Current Register with 5-mΩ Sense Resistor (I2C address = 03h) Field Descriptions
BIT FIELD TYPE RESET DESCRIPTION
7-5 Reserved R/W 000b

Not used. 1 = invalid write.
4 Charge Current, bit 6 R/W 0b

0 = Adds 0 mA of charger current.

1 = Adds 8192 mA of charger current.
3 Charge Current, bit 5 R/W 0b

0 = Adds 0 mA of charger current.

1 = Adds 4096 mA of charger current.
2 Charge Current, bit 4 R/W 0b

0 = Adds 0 mA of charger current.

1 = Adds 2048 mA of charger current.
1 Charge Current, bit 3 R/W 0b

0 = Adds 0 mA of charger current.

1 = Adds 1024 mA of charger current.
0 Charge Current, bit 2 R/W 0b

0 = Adds 0 mA of charger current.

1 = Adds 512 mA of charger current.
Table 8-11 Charge Current Register with 5-mΩ Sense Resistor (I2C address = 02h) Field Descriptions
BIT FIELD TYPE RESET DESCRIPTION
7 Charge Current, bit 1 R/W 0b

0 = Adds 0 mA of charger current.

1 = Adds 256 mA of charger current.
6 Charge Current, bit 0 R/W 0b

0 = Adds 0 mA of charger current.

1 = Adds 128 mA of charger current.
5-0 Reserved R/W 000000b

Not used. Value Ignored.