ZHCSET0D December   2015  – December 2019 TPS2H000-Q1

PRODUCTION DATA.  

  1. 特性
  2. 应用
  3. 说明
    1.     Device Images
      1.      典型应用原理图
      2.      驱动具有可调节电流限制的电容性负载
  4. 修订历史记录
  5. Device Comparison Table
  6. Pin Configuration and Functions
    1.     Pin Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Switching Characteristics
    7. 7.7 Typical Characteristics
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Pin Current and Voltage Conventions
      2. 8.3.2 Accurate Current Sense
      3. 8.3.3 Adjustable Current Limit
      4. 8.3.4 Inductive-Load Switching-Off Clamp
      5. 8.3.5 Fault Detection and Reporting
        1. 8.3.5.1 Diagnostic Enable Function
        2. 8.3.5.2 Multiplexing of Current Sense
        3. 8.3.5.3 Fault Table
        4. 8.3.5.4 STx and FAULT Reporting
      6. 8.3.6 Full Diagnostics
        1. 8.3.6.1 Short-to-GND and Overload Detection
        2. 8.3.6.2 Open-Load Detection
          1. 8.3.6.2.1 Channel On
          2. 8.3.6.2.2 Channel Off
        3. 8.3.6.3 Short-to-Battery Detection
        4. 8.3.6.4 Reverse Polarity Detection
        5. 8.3.6.5 Thermal Fault Detection
          1. 8.3.6.5.1 Thermal Shutdown
      7. 8.3.7 Full Protections
        1. 8.3.7.1 UVLO Protection
        2. 8.3.7.2 Loss-of-GND Protection
        3. 8.3.7.3 Protection for Loss of Power Supply
        4. 8.3.7.4 Reverse-Current Protection
        5. 8.3.7.5 MCU I/O Protection
    4. 8.4 Device Functional Modes
      1. 8.4.1 Working Modes
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Examples
      1. 11.2.1 Without a GND Network
      2. 11.2.2 With a GND Network
  12. 12器件和文档支持
    1. 12.1 接收文档更新通知
    2. 12.2 社区资源
    3. 12.3 商标
    4. 12.4 静电放电警告
    5. 12.5 Glossary
  13. 13机械、封装和可订购信息

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

Electrical Characteristics

5 V < VVS < 40 V; −40°C < TJ < 150°C, unless otherwise specified)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
OPERATING VOLTAGE
VVS(nom) Nominal operating voltage 4 40 V
VVS(uvr) Undervoltage turnon VVS rises up 3.5 3.7 4 V
VVS(uvf) Undervoltage shutdown VVS falls down 3 3.2 3.4 V
V(uv,hys) Undervoltage shutdown, hysteresis 0.5 V
OPERATING CURRENT
I(op) Nominal operating current(1) VVS = 13.5 V, VINx = 5 V, VDIAG_EN = 0 V, IOUTx = 0.1 A, current limit = 0.5 A, all channels on 7 mA
I(off) Standby current VVS = 13.5 V, VINx = VDIAG_EN = VCS = VCL = VOUTx = THER = 0 V,
TJ = 25°C
0.5 µA
VVS = 13.5 V, VINx = VDIAG_EN = VCS = VCL = VOUTx = THER = 0 V,
TJ = 125°C
3
I(off,diag) Standby current with diagnostic enabled VVS = 13.5 V, VINx = 0 V, VDIAG_EN = 5 V, VVS – VOUTx > V(ol,off), not in open-load mode 3 mA
t(off,diag) Standby mode deglitch time(1) IN from high to low, if deglitch time > t(off,deg), the device enters into standby mode. 10 12.5 15 ms
Ilkg(out) Output leakage current in off-state VVS = 13.5 V, VINx = VOUTx = 0, VDIAG_EN = 5 V 2 µA
POWER STAGE
rDS(on) On-state resistance(1) VVS ≥ 3.5 V, TJ = 25°C 1000
VVS ≥ 3.5 V, TJ = 150°C 2000
ICL(int) Internal current limit Internal current limit value, CL pin connected to GND 1 1.6 A
ICL(TSD) Current limit during thermal shutdown(1) Internal current limit value under thermal shutdown 0.8 A
External current limit value under thermal shutdown. The percentage of the external current limit setting value 60%
VDS(clamp) Drain-to-source internal clamp voltage 46 65 V
OUTPUT DIODE CHARACTERISTICS
VF Drain−source diode voltage IN = 0, IOUTx = −0.15 A. 0.3 0.8 1 V
IR(1), IR(2) Continuous reverse current from source to drain(1) t < 60 s, VINx = 0 V, TJ = 25°C, single channel reversed, short-to-battery condition 1 A
t < 60 s, VINx = 0 V, GND pin 1-kΩ resistor in parallel with diode. TJ = 25°C. Reverse-polarity condition, all channels reversed 1
LOGIC INPUT (INx, DIAG_EN, SEL, THER)
VIH Logic high-level voltage 2 V
VIL Logic low-level voltage 0.8 V
R(logic,pd) Logic-pin pulldown resistor INx, SEL, THER, VINx = VSEL = VTHER = 5 V 100 175 250
DIAG_EN. VVS = VDIAG_EN = 5 V 150 275 400
DIAGNOSTICS
Ilkg(GND_loss) Output leakage current under GND loss condition 100 µA
V(ol,off) Open-load detection threshold IN = 0 V, when VVS – VOUTx < V(ol,off), duration longer than t(ol,off), then open load is detected, off state 1.6 2.6 V
td(ol,off) Open-load detection threshold deglitch time (see Figure 3) IN = 0 V, when VVS – VOUTx < V(ol,off) , duration longer than t(ol,off), then open load is detected, off state 300 600 800 µs
I(ol,off) Off-state output sink current VINx = 0 V, VDIAG_EN = 5 V, VVS = VOUTx = 13.5 V, TJ = 125°C, open load –75 µA
VOL(STx) Status low-output voltage ISTx = 2 mA, version A only 0.2 V
VOL(FAULT) Fault low-output voltage IFAULT = 2 mA, version B only 0.2 V
tCL(deg) Deglitch time when current limit occurs(1) VINx = VDIAG_EN = 5 V, the deglitch time from current limit toggling to FAULT, STx, CS report. 80 180 µs
T(SD) Thermal shutdown threshold(1) 160 175 °C
T(SD,rst) Thermal shutdown status reset threshold(1) 155 °C
T(SW) Thermal swing shutdown threshold(1) 60 °C
T(hys) Hysteresis for resetting the thermal shutdown or thermal swing(1) 10 °C
CURRENT SENSE (Version B) AND CURRENT LIMIT
K(CS) Current-sense ratio 80
K(CL) Current-limit ratio 300
VCL(th) Current limit internal threshold(1) 0.8 V
dK(CS) / K(CS) Current-sense accuracy, (ICS × K(CS) – IOUTx) /IOUTx × 100 VVS = 13.5 V, IOUTx ≥ 1 mA –50% 50%
VVS = 13.5 V, IOUTx ≥ 2 mA –25% 25%
VVS = 13.5 V, IOUTx ≥ 5 mA –10% 10%
VVS = 13.5 V, IOUTx ≥ 25 mA –3% 3%
VVS = 13.5 V, IOUTx ≥ 100 mA –2.5% 2.5%
dK(CL) / K(CL) External current limit accuracy(2) (IOUTx – ICL × K(CL)) × 100 / (ICL × K(CL)) VVS = 13.5 V, I(limit) ≥ 50 mA –25% 25%
I(limit) ≥ 100 mA –20% 20%
I(limit) ≥ 200 mA –15% 15%
VVS = 13.5 V, 0.5 A ≤ I(limit) ≤ 0.9 A –10% 10%
VCS(lin) Current-sense voltage linear range(1) VVS ≥ 6.5 V 0 4 V
5 V ≤ VVS < 6.5 V 0 VVS – 2.5
IOUTx(lin) Output-current linear range(1) VVS = 13.5 V, VCS(lin) ≤ 4 V 0 0.75 A
5 V ≤ VVS < 6.5 V, VCS(lin) ≤ VVS – 2.5 V 0 0.5
VCS(H) Current sense pin output voltage(1) VVS ≥ 7 V, fault mode 4.5 6.5 V
5 V ≤ VVS < 7 V, fault mode Min(VVS – 2, 4.5) 6.5 V
ICS(H) Current-sense pin output current VCS = 4.5 V, VVS = 13.5 V 15 mA
Ilkg(CS) Current-sense leakage current in disabled mode VDIAG_EN = 0 V, TJ = 125ºC 0.5 µA
Value specified by design, not subject to production test
External current limit accuracy is only applicable to overload conditions greater than 1.5 x the current limit setting