ZHCSO18A december   2022  – june 2023 TPS281C30

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Thermal Information
    6. 7.6 Electrical Characteristics
    7. 7.7 SNS Timing Characteristics
    8. 7.8 Switching Characteristics
    9. 7.9 Typical Characteristics
  9. 8 Parameter Measurement Information
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Device Functional Modes
      1. 9.3.1 Working Mode
    4. 9.4 Feature Description
      1. 9.4.1 Accurate Current Sense
        1. 9.4.1.1 High Accuracy Sense Mode
      2. 9.4.2 Programmable Current Limit
        1. 9.4.2.1 Short-Circuit and Overload Protection
        2. 9.4.2.2 Capacitive Charging
      3. 9.4.3 Inductive-Load Switching-Off Clamp
      4. 9.4.4 Inductive Load Demagnetization
      5. 9.4.5 Full Protections and Diagnostics
        1. 9.4.5.1 Open-Load Detection
        2. 9.4.5.2 Thermal Protection Behavior
        3. 9.4.5.3 Undervoltage Lockout (UVLO) Protection
        4. 9.4.5.4 Overvoltage (OVP) Protection
        5. 9.4.5.5 Reverse Polarity Protection
        6. 9.4.5.6 Protection for MCU I/Os
        7. 9.4.5.7 Diagnostic Enable Function
        8. 9.4.5.8 Loss of Ground
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
        1. 10.2.1.1 IEC 61000-4-5 Surge
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Selecting RILIM
        2. 10.2.2.2 Selecting RSNS
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
        1. 10.4.1.1 EMC Considerations
      2. 10.4.2 Layout Example
        1. 10.4.2.1 PWP Layout without a GND Network
        2. 10.4.2.2 PWP Layout with a GND Network
        3. 10.4.2.3 RGW Layout with a GND Network
      3. 10.4.3 Thermal Considerations
  12. 11Device and Documentation Support
    1. 11.1 接收文档更新通知
    2. 11.2 支持资源
    3. 11.3 Trademarks
    4. 11.4 静电放电警告
    5. 11.5 术语表
  13. 12Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

10.2.2.1 Selecting RILIM

In this application, the TPS281C30A must allow for the maximum DC current with margin but minimize the energy in the switch and the load on the input supply during a fault condition by minimizing the current limit.

The nominal current limit should be set such that the worst case (lowest) current limit will be higher than the maximum load current (4 A). Since the lower limit is 10% below the typical value, for this application, the best ILIM set point is approximately 5.5A. The below equation allows you to calculate the RILIM value that is placed from the ILIMx pins to GND pin of the device. RILIM is calculated in kΩ.

Equation 11. RILIM = KCL / ICL

The KCL value in the Specifications section is 50A/kΩ. So the calculated value of RILIM is 9.09 kΩ which can be found as a standard 1% resistor.