ZHCSFM5A September   2016  – October 2016 TPA3245

PRODUCTION DATA.  

  1. 特性
  2. 应用
  3. 说明
  4. 修订历史记录
  5. Device Comparison Table
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics
    6. 7.6  Audio Characteristics (BTL)
    7. 7.7  Audio Characteristics (SE)
    8. 7.8  Audio Characteristics (PBTL)
    9. 7.9  Typical Characteristics, BTL Configuration
    10. 7.10 Typical Characteristics, SE Configuration
    11. 7.11 Typical Characteristics, PBTL Configuration
  8. Parameter Measurement Information
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagrams
    3. 9.3 Feature Description
      1. 9.3.1 Error Reporting
    4. 9.4 Device Protection System
      1. 9.4.1 Overload and Short Circuit Current Protection
      2. 9.4.2 Signal Clipping and Pulse Injector
      3. 9.4.3 DC Speaker Protection
      4. 9.4.4 Pin-to-Pin Short Circuit Protection (PPSC)
      5. 9.4.5 Overtemperature Protection OTW and OTE
      6. 9.4.6 Undervoltage Protection (UVP) and Power-on Reset (POR)
      7. 9.4.7 Fault Handling
      8. 9.4.8 Device Reset
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Applications
      1. 10.2.1 Stereo BTL Application
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedures
          1. 10.2.1.2.1 Decoupling Capacitor Recommendations
          2. 10.2.1.2.2 PVDD Capacitor Recommendation
          3. 10.2.1.2.3 PCB Material Recommendation
          4. 10.2.1.2.4 Oscillator
      2. 10.2.2 Application Curves
      3. 10.2.3 Typical Application, Single Ended (1N) SE
        1. 10.2.3.1 Design Requirements
        2. 10.2.3.2 Detailed Design Procedures
        3. 10.2.3.3 Application Curves
      4. 10.2.4 Typical Application, Differential (2N), PBTL (Outputs Paralleled before LC filter)
        1. 10.2.4.1 Design Requirements
        2. 10.2.4.2 Detailed Design Procedures
        3. 10.2.4.3 Application Curves
      5. 10.2.5 Typical Application, Differential (2N), PBTL (Outputs Paralleled after LC filter)
        1. 10.2.5.1 Design Requirements
        2. 10.2.5.2 Detailed Design Procedures
  11. 11Power Supply Recommendations
    1. 11.1 Power Supplies
      1. 11.1.1 VDD Supply
      2. 11.1.2 GVDD_X Supply
      3. 11.1.3 PVDD Supply
    2. 11.2 Powering Up
    3. 11.3 Powering Down
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Examples
      1. 12.2.1 BTL Application Printed Circuit Board Layout Example
      2. 12.2.2 SE Application Printed Circuit Board Layout Example
      3. 12.2.3 PBTL (Outputs Paralleled before LC filter) Application Printed Circuit Board Layout Example
      4. 12.2.4 PBTL (Outputs Paralleled after LC filter) Application Printed Circuit Board Layout Example
  13. 13器件和文档支持
    1. 13.1 文档支持
    2. 13.2 接收文档更新通知
    3. 13.3 社区资源
    4. 13.4 商标
    5. 13.5 静电放电警告
    6. 13.6 Glossary
  14. 14机械、封装和可订购信息

封装选项

请参考 PDF 数据表获取器件具体的封装图。

机械数据 (封装 | 引脚)
  • DDV|44
散热焊盘机械数据 (封装 | 引脚)
订购信息

Pin Configuration and Functions

The TPA3245 is available in a thermally enhanced TSSOP package.

The package type contains a PowerPad™ that is located on the top side of the device for convenient thermal coupling to the heat sink.

DDV Package
HTSSOP 44-Pin
(Top View)

Pin Functions

NAME NO. I/O DESCRIPTION
AVDD 14 P Internal voltage regulator, analog section
BST_A 44 P HS bootstrap supply (BST), external 0.033 μF capacitor to OUT_A required.
BST_B 43 P HS bootstrap supply (BST), external 0.033 μF capacitor to OUT_B required.
BST_C 24 P HS bootstrap supply (BST), external 0.033 μF capacitor to OUT_C required.
BST_D 23 P HS bootstrap supply (BST), external 0.033 μF capacitor to OUT_D required.
CLIP_OTW 21 O Clipping warning and Over-temperature warning; open drain; active low. Do not connect if not used.
C_START 15 O Startup ramp, requires a charging capacitor to GND
DVDD 11 P Internal voltage regulator, digital section
FAULT 19 O Shutdown signal, open drain; active low. Do not connect if not used.
FREQ_ADJ 8 O Oscillator frequency programming pin
GND 12, 13, 25, 26, 33, 34, 41, 42 P Ground
GVDD_AB 1 P Gate-drive voltage supply; AB-side, requires 0.1 µF capacitor to GND
GVDD_CD 22 P Gate-drive voltage supply; CD-side, requires 0.1 µF capacitor to GND
INPUT_A 5 I Input signal for half bridge A
INPUT_B 6 I Input signal for half bridge B
INPUT_C 16 I Input signal for half bridge C
INPUT_D 17 I Input signal for half bridge D
M1 3 I Mode selection 1 (LSB)
M2 4 I Mode selection 2 (MSB)
OC_ADJ 7 I/O Over-Current threshold programming pin
OSC_IOM 9 I/O Oscillator synchronization interface. Do not connect if not used.
OSC_IOP 10 O Oscillator synchronization interface. Do not connect if not used.
OUT_A 39, 40 O Output, half bridge A
OUT_B 35 O Output, half bridge B
OUT_C 32 O Output, half bridge C
OUT_D 27, 28 O Output, half bridge D
PVDD_AB 36, 37, 38 P PVDD supply for half-bridge A and B
PVDD_CD 29, 30, 31 P PVDD supply for half-bridge C and D
RESET 18 I Device reset Input; active low
VDD 2 P Power supply for internal voltage regulator requires a 10-µF capacitor with a 0.1-µF capacitor to GND for decoupling.
VBG 20 P Internal voltage reference requires a 0.1-µF capacitor to GND for decoupling.
PowerPad™ P Ground, connect to grounded heat sink

Table 1. Mode Selection Pins

MODE PINS INPUT MODE OUTPUT CONFIGURATION DESCRIPTION
M2 M1
0 0 2N + 1 2 × BTL Stereo BTL output configuration
0 1 2N/1N + 1 1 x BTL + 2 x SE 2.1 BTL + SE mode. Channel AB: BTL, channel C + D: SE
1 0 2N + 1 1 x PBTL Parallelled BTL configuration. Connect INPUT_C and INPUT_D to GND.
1 1 1N +1 4 x SE Single ended output configuration