ZHCSRQ0F june   2004  – february 2023 SN65HVD485E

PRODUCTION DATA  

  1. 特性
  2. 应用
  3. 说明
  4. Revision History
  5. Device Comparison Table
    1.     6
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics: Driver
    6. 7.6  Electrical Characteristics: Receiver
    7. 7.7  Power Dissipation Characteristics
    8. 7.8  Supply Current
    9. 7.9  Switching Characteristics: Driver
    10. 7.10 Switching Characteristics: Receiver
    11. 7.11 Dissipation Ratings
    12. 7.12 Typical Characteristics
      1.      Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
    4. 8.4 Device Functional Modes
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
        1. 9.2.1.1 Data Rate and Bus Length
        2. 9.2.1.2 Stub Length
        3. 9.2.1.3 Bus Loading
        4. 9.2.1.4 Receiver Failsafe
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Power Usage in an RS-485 Transceiver
      3. 9.2.3 Application Curve
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  10. 10Device and Documentation Support
    1. 10.1 Device Support
      1. 10.1.1 Device Nomenclature
        1. 10.1.1.1 Thermal Characteristics of IC Packages
    2. 10.2 Documentation Support
      1. 10.2.1 Related Documentation
    3. 10.3 支持资源
    4. 10.4 Trademarks
    5. 10.5 静电放电警告
    6. 10.6 术语表
  11. 11Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

说明

SN65HVD485E 器件是专为 RS-485 数据总线网络设计的半双工收发器。该器件由 5V 电源供电,完全符合 TIA/EIA-485A 标准。该器件适用于通过长双绞线电缆以高达 10Mbps 的速率传输数据,并且设计用于在非常低的电源电流(通常小于 2mA,不包括负载)下运行。当器件处于非活动关断模式时,电源电流降至 1mA 以下。

该器件的宽共模范围和高 ESD 保护级别使其适用于要求苛刻的应用,例如电气逆变器、电信机架上的状态/命令信号、有线机箱互连以及噪声容限至关重要的工业自动化网络。SN65HVD485E 器件符合 SN75176 器件的业界通用尺寸。上电复位电路使输出保持高阻抗状态,直到电源电压稳定。热关断功能可保护器件免受系统故障问题造成的损坏。SN65HVD485E 器件可在 –40°C 至 85°C 气温下运行。

封装信息
器件型号 封装(1) 封装尺寸(标称值)
SN65HVD485E SOIC (8) 4.91mm × 3.90mm
VSSOP (8) 3.00mm × 3.00mm
PDIP (8) 9.81mm × 6.35mm
如需了解所有可用封装,请参阅数据表末尾的可订购产品附录。
GUID-BA89E5AC-7C69-4546-BABD-4ED09520FA57-low.gif典型应用原理图