ZHCSJB5B September   2019  – December 2019 DRV8904-Q1 , DRV8906-Q1 , DRV8908-Q1 , DRV8910-Q1 , DRV8912-Q1

UNLESS OTHERWISE NOTED, this document contains PRODUCTION DATA.  

  1. 特性
  2. 应用
  3. 说明
    1.     简化原理图
  4. 修订历史记录
  5. Device Comparison Table
  6. Pin Configuration and Functions
    1.     Pin Functions—DRV8912-Q1
    2.     Pin Functions—DRV8910-Q1
    3.     Pin Functions—DRV8908-Q1
    4.     Pin Functions—DRV8906-Q1
    5.     Pin Functions—DRV8904-Q1
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Timing Requirements
    7. 7.7 Typical Characteristics
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Half Bridge Drivers
        1. 8.3.1.1 Control Modes
          1. 8.3.1.1.1 Continuous Mode (Without PWM)
          2. 8.3.1.1.2 Chopping Mode (With PWM)
            1. 8.3.1.1.2.1 PWM Configuration
            2. 8.3.1.1.2.2 Free-Wheeling Mode (Synchronous Rectification) Disable / Enable
            3. 8.3.1.1.2.3 PWM Channels Mapping
            4. 8.3.1.1.2.4 PWM Channels Configuration (PWM Frequency and PWM Duty)
            5. 8.3.1.1.2.5 Half-Bridge Enable
          3. 8.3.1.1.3 Parallel Mode (Continuous Operation)
          4. 8.3.1.1.4 Parallel Mode (PWM Operation)
            1. 8.3.1.1.4.1 PWM Configuration
            2. 8.3.1.1.4.2 Free-Wheeling Mode (Synchronous Rectification) Disable / Enable
            3. 8.3.1.1.4.3 PWM Channels Mapping
            4. 8.3.1.1.4.4 PWM Channels Configuration (PWM Frequency and PWM Duty)
            5. 8.3.1.1.4.5 PWM Generators Disable
            6. 8.3.1.1.4.6 Half-Bridge Enable
            7. 8.3.1.1.4.7 PWM Generators Enable
        2. 8.3.1.2 Half-Bridge Drive Architecture
          1. 8.3.1.2.1 Slew Rate
          2. 8.3.1.2.2 Cross Conduction (Dead Time)
          3. 8.3.1.2.3 Propagation Delay
      2. 8.3.2 Pin Diagrams
        1. 8.3.2.1 Logic Level Input Pin (nSLEEP, SCLK and SDI)
        2. 8.3.2.2 Logic Level Input Pin (nSCS)
        3. 8.3.2.3 Open Drain Output Pin (nFAULT)
        4. 8.3.2.4 Push Pull Output Pin (SDO)
      3. 8.3.3 Protection Circuits
        1. 8.3.3.1 VM Supply Undervoltage Lockout (UVLO)
        2. 8.3.3.2 VM Supply Overvoltage Protection (OVP)
        3. 8.3.3.3 Logic Supply Power on Reset (POR)
        4. 8.3.3.4 Overcurrent Protection (OCP)
        5. 8.3.3.5 Open-load detection (OLD)
          1. 8.3.3.5.1 Active OLD
            1. 8.3.3.5.1.1 Negative-current OLD
          2. 8.3.3.5.2 Low-current OLD
          3. 8.3.3.5.3 Passive OLD
        6. 8.3.3.6 Thermal Warning (OTW)
        7. 8.3.3.7 Thermal Shutdown (OTSD)
    4. 8.4 Device Functional Modes
      1. 8.4.1 Sleep Mode (nSLEEP = 0)
      2. 8.4.2 Operating Mode (nSLEEP = 1)
      3. 8.4.3 Fault Mode
    5. 8.5 Programming
      1. 8.5.1 SPI
      2. 8.5.2 SPI Format
      3. 8.5.3 SPI Interface for Multiple Slaves
        1. 8.5.3.1 SPI Interface for Multiple Slaves in Daisy Chain
    6. 8.6 Register Map
      1. 8.6.1 DRV8912-Q1 and DRV8910-Q1 Register Maps
        1. 8.6.1.1 Status Registers
          1. 8.6.1.1.1 IC Status (IC_STAT) Register (Address = 0x00) [reset = 0x00]
            1. Table 20. IC Status Register Field Descriptions
          2. 8.6.1.1.2 Overcurrent Protection (OCP) Status 1 (OCP_STAT_1) Register (Address = 0x01) [reset = 0x00]
            1. Table 21. Overcurrent Protection (OCP) Status 1 Register Field Descriptions
          3. 8.6.1.1.3 Overcurrent Protection (OCP) Status 2 (OCP_STAT_2) Register (Address = 0x02) [reset = 0x00]
            1. Table 22. Overcurrent Protection (OCP) Status 2 Register Field Descriptions
          4. 8.6.1.1.4 Overcurrent Protection (OCP) Status 3 (OCP_STAT_3) Register (Address = 0x03) [reset = 0x00]
            1. Table 23. Overcurrent Protection (OCP) Status 3 Register Field Descriptions
          5. 8.6.1.1.5 Open-Load Detect (OLD) Status 1 (OLD_STAT_1) Register (Address = 0x04) [reset = 0x00]
            1. Table 24. Open-Load Detect (OLD) Status 1 Register Field Descriptions
          6. 8.6.1.1.6 Open-Load Detect (OLD) Status 2 (OLD_STAT_2) Register (Address = 0x05) [reset = 0x00]
            1. Table 25. Open-Load Detect (OLD) Status 2 Register Field Descriptions
          7. 8.6.1.1.7 Open-Load Detect (OLD) Status 3 (OLD_STAT_3) Register (Address = 0x06) [reset = 0x00]
            1. Table 26. Open-Load Detect (OLD) Status 3 Register Field Descriptions
        2. 8.6.1.2 Control Registers
          1. 8.6.1.2.1  Configuration (CONFIG_CTRL) Register (Address = 0x07) [reset = 0x00]
            1. Table 28. Configuration Register Field Descriptions
          2. 8.6.1.2.2  Operation Control 1 (OP_CTRL_1) Register (Address = 0x08) [reset = 0x00]
            1. Table 29. Operation Control 1 Register Field Descriptions
          3. 8.6.1.2.3  Operation Control 2 (OP_CTRL_2) Register (Address = 0x09) [reset = 0x00]
            1. Table 30. Operation Control 2 Register Field Descriptions
          4. 8.6.1.2.4  Operation Control 3 (OP_CTRL_3) Register (Address = 0x0A) [reset = 0x00]
            1. Table 31. Operation Control 3 Register Field Descriptions
          5. 8.6.1.2.5  PWM Control 1 (PWM_CTRL_1) Register (Address = 0x0B) [reset = 0x00]
            1. Table 32. PWM Control 1 Register Field Descriptions
          6. 8.6.1.2.6  PWM Control 2 (PWM_CTRL_2) Register (Address = 0x0C) [reset = 0x00]
            1. Table 33. PWM Control 2 Register Field Descriptions
          7. 8.6.1.2.7  Free-Wheeling Control 1 (FW_CTRL_1) Register (Address = 0x0D) [reset = 0x00]
            1. Table 34. Free-Wheeling Control 1 Register Field Descriptions
          8. 8.6.1.2.8  Free-Wheeling Control 2 (FW_CTRL_2) Register (Address = 0x0E) [reset = 0x00]
            1. Table 35. Free-Wheeling Control 2 Register Field Descriptions
          9. 8.6.1.2.9  PWM Map Control 1 (PWM_MAP_CTRL_1) Register (Address = 0x0F) [reset = 0x00]
            1. Table 36. PWM Map Control 1 Register Field Descriptions
          10. 8.6.1.2.10 PWM Map Control 2 (PWM_MAP_CTRL_2) Register (Address = 0x10) [reset = 0x00]
            1. Table 37. PWM Map Control 2 Register Field Descriptions
          11. 8.6.1.2.11 PWM Map Control 3 (PWM_MAP_CTRL_3) Register (Address = 0x11) [reset = 0x00]
            1. Table 38. PWM Map Control 3 Register Field Descriptions
          12. 8.6.1.2.12 PWM Frequency Control (PWM_FREQ_CTRL) Register (Address = 0x12) [reset = 0x00]
            1. Table 39. PWM Frequency Control Register Field Descriptions
          13. 8.6.1.2.13 PWM Duty Control Channel 1 (PWM_DUTY_CH1) Register (Address = 0x13) [reset = 0x00]
            1. Table 40. PWM Duty Control Channel 1 Register Field Descriptions
          14. 8.6.1.2.14 PWM Duty Control Channel 2 (PWM_DUTY_CH2) Register (Address = 0x14) [reset = 0x00]
            1. Table 41. PWM Duty Control Channel 2 Register Field Descriptions
          15. 8.6.1.2.15 PWM Duty Control Channel 3 (PWM_DUTY_CH3) Register (Address = 0x15) [reset = 0x00]
            1. Table 42. PWM Duty Control Channel 3 Register Field Descriptions
          16. 8.6.1.2.16 PWM Duty Control Channel 4 (PWM_DUTY_CH4) Register (Address = 0x16) [reset = 0x00]
            1. Table 43. PWM Duty Control Channel 4 Register Field Descriptions
          17. 8.6.1.2.17 Slew Rate Control 1 (SR_CTRL_1) Register (Address = 0x17) [reset = 0x00]
            1. Table 44. Slew Rate Control 1 Register Field Descriptions
          18. 8.6.1.2.18 Slew Rate Control 2 (SR_CTRL_2) Register (Address = 0x18) [reset = 0x00]
            1. Table 45. Slew Rate Control 2 Register Field Descriptions
          19. 8.6.1.2.19 Open-Load Detect (OLD) Control 1 (OLD_CTRL_1) Register (Address = 0x19) [reset = 0x00]
            1. Table 46. Open-Load Detect (OLD) Control (OLD_CTRL_1) Register Field Descriptions
          20. 8.6.1.2.20 Open-Load Detect (OLD) Control 2 (OLD_CTRL_2) Register (Address = 0x1A) [reset = 0x00]
            1. Table 47. Open-Load Detect (OLD) Control (OLD_CTRL_2) Register Field Descriptions
          21. 8.6.1.2.21 Open-Load Detect (OLD) Control 3 (OLD_CTRL_3) Register (Address = 0x1B) [reset = 0x00]
            1. Table 48. Open-Load Detect (OLD) Control (OLD_CTRL_3) Register Field Descriptions
          22. 8.6.1.2.22 Open-Load Detect (OLD) Control 4 (OLD_CTRL_4) Register (Address = 0x24) [reset = 0x00]
            1. Table 49. Open-Load Detect (OLD) Control (OLD_CTRL_4) Register Field Descriptions
      2. 8.6.2 DRV8908-Q1, DRV8906-Q1 and DRV8904-Q1 Register Maps
        1. 8.6.2.1 Status Registers
          1. 8.6.2.1.1 IC Status (IC_STAT) Register (Address = 0x00) [reset = 0x00]
            1. Table 54. IC Status Register Field Descriptions
          2. 8.6.2.1.2 Overcurrent Protection (OCP) Status 1 (OCP_STAT_1) Register (Address = 0x01) [reset = 0x00]
            1. Table 55. Overcurrent Protection (OCP) Status 1 Register Field Descriptions
          3. 8.6.2.1.3 Overcurrent Protection (OCP) Status 2 (OCP_STAT_2) Register (Address = 0x02) [reset = 0x00]
            1. Table 56. Overcurrent Protection (OCP) Status 2 Register Field Descriptions
          4. 8.6.2.1.4 Overcurrent Protection (OCP) Status 3 (OCP_STAT_3) Register (Address = 0x03) [reset = 0x00]
            1. Table 57. Overcurrent Protection (OCP) Status 3 Register Field Descriptions
          5. 8.6.2.1.5 Open-Load Detect (OLD) Status 1 (OLD_STAT_1) Register (Address = 0x04) [reset = 0x00]
            1. Table 58. Open-Load Detect (OLD) Status 1 Register Field Descriptions
          6. 8.6.2.1.6 Open-Load Detect (OLD) Status 2 (OLD_STAT_2) Register (Address = 0x05) [reset = 0x00]
            1. Table 59. Open-Load Detect (OLD) Status 2 Register Field Descriptions
          7. 8.6.2.1.7 Open-Load Detect (OLD) Status 3 (OLD_STAT_3) Register (Address = 0x06) [reset = 0x00]
            1. Table 60. Open-Load Detect (OLD) Status 3 Register Field Descriptions
        2. 8.6.2.2 Control Registers
          1. 8.6.2.2.1  Configuration (CONFIG_CTRL) Register (Address = 0x07) [reset = 0x00]
            1. Table 62. Configuration Register Field Descriptions
          2. 8.6.2.2.2  Operation Control 1 (OP_CTRL_1) Register (Address = 0x08) [reset = 0x00]
            1. Table 63. Operation Control 1 Register Field Descriptions
          3. 8.6.2.2.3  Operation Control 2 (OP_CTRL_2) Register (Address = 0x09) [reset = 0x00]
            1. Table 64. Operation Control 2 Register Field Descriptions
          4. 8.6.2.2.4  Operation Control 3 (OP_CTRL_3) Register (Address = 0x0A) [reset = 0x00]
            1. Table 65. Operation Control 3 Register Field Descriptions
          5. 8.6.2.2.5  PWM Control 1 (PWM_CTRL_1) Register (Address = 0x0B) [reset = 0x00]
            1. Table 66. PWM Control 1 Register Field Descriptions
          6. 8.6.2.2.6  PWM Control 2 (PWM_CTRL_2) Register (Address = 0x0C) [reset = 0x00]
            1. Table 67. PWM Control 2 Register Field Descriptions
          7. 8.6.2.2.7  Free-Wheeling Control 1 (FW_CTRL_1) Register (Address = 0x0D) [reset = 0x00]
            1. Table 68. Free-Wheeling Control 1 Register Field Descriptions
          8. 8.6.2.2.8  Free-Wheeling Control 2 (FW_CTRL_2) Register (Address = 0x0E) [reset = 0x00]
            1. Table 69. Free-Wheeling Control 2 Register Field Descriptions
          9. 8.6.2.2.9  PWM Map Control 1 (PWM_MAP_CTRL_1) Register (Address = 0x0F) [reset = 0x00]
            1. Table 70. PWM Map Control 1 Register Field Descriptions
          10. 8.6.2.2.10 PWM Map Control 2 (PWM_MAP_CTRL_2) Register (Address = 0x10) [reset = 0x00]
            1. Table 71. PWM Map Control 2 Register Field Descriptions
          11. 8.6.2.2.11 PWM Map Control 3 (PWM_MAP_CTRL_3) Register (Address = 0x11) [reset = 0x00]
            1. Table 72. PWM Map Control 3 Register Field Descriptions
          12. 8.6.2.2.12 PWM Map Control 4 (PWM_MAP_CTRL_4) Register (Address = 0x12) [reset = 0x00]
            1. Table 73. PWM Map Control 4 Register Field Descriptions
          13. 8.6.2.2.13 PWM Frequency Control 1 (PWM_FREQ_CTRL_1) Register (Address = 0x13 [reset = 0x00]
            1. Table 74. PWM Frequency Control 1 Register Field Descriptions
          14. 8.6.2.2.14 PWM Frequency Control 2 (PWM_FREQ_CTRL_2) Register (Address = 0x14 [reset = 0x00]
            1. Table 75. PWM Frequency Control 2 Register Field Descriptions
          15. 8.6.2.2.15 PWM Duty Control Channel 1 (PWM_DUTY_CH1) Register (Address = 0x15) [reset = 0x00]
            1. Table 76. PWM Duty Control Channel 1 Register Field Descriptions
          16. 8.6.2.2.16 PWM Duty Control Channel 2 (PWM_DUTY_CH2) Register (Address = 0x16) [reset = 0x00]
            1. Table 77. PWM Duty Control Channel 2 Register Field Descriptions
          17. 8.6.2.2.17 PWM Duty Control Channel 3 (PWM_DUTY_CH3) Register (Address = 0x17) [reset = 0x00]
            1. Table 78. PWM Duty Control Channel 3 Register Field Descriptions
          18. 8.6.2.2.18 PWM Duty Control Channel 4 (PWM_DUTY_CH4) Register (Address = 0x18) [reset = 0x00]
            1. Table 79. PWM Duty Control Channel 4 Register Field Descriptions
          19. 8.6.2.2.19 PWM Duty Control Channel 5 (PWM_DUTY_CH5) Register (Address = 0x19) [reset = 0x00]
            1. Table 80. PWM Duty Control Channel 5 Register Field Descriptions
          20. 8.6.2.2.20 PWM Duty Control Channel 6 (PWM_DUTY_CH6) Register (Address = 0x1A) [reset = 0x00]
            1. Table 81. PWM Duty Control Channel 6 Register Field Descriptions
          21. 8.6.2.2.21 PWM Duty Control Channel 7 (PWM_DUTY_CH7) Register (Address = 0x1B) [reset = 0x00]
            1. Table 82. PWM Duty Control Channel 7 Register Field Descriptions
          22. 8.6.2.2.22 PWM Duty Control Channel 8 (PWM_DUTY_CH8) Register (Address = 0x1C) [reset = 0x00]
            1. Table 83. PWM Duty Control Channel 8 Register Field Descriptions
          23. 8.6.2.2.23 Slew Rate Control 1 (SR_CTRL_1) Register (Address = 0x1D [reset = 0x00]
            1. Table 84. Slew Rate Control 1 Register Field Descriptions
          24. 8.6.2.2.24 Slew Rate Control 2 (SR_CTRL_2) Register (Address = 0x1E) [reset = 0x00]
            1. Table 85. Slew Rate Control 2 Register Field Descriptions
          25. 8.6.2.2.25 Open-Load Detect (OLD) Control 1 (OLD_CTRL_1) Register (Address = 0x1F) [reset = 0x00]
            1. Table 86. Open-Load Detect (OLD) Control (OLD_CTRL_1) Register Field Descriptions
          26. 8.6.2.2.26 Open-Load Detect (OLD) Control 2 (OLD_CTRL_2) Register (Address = 0x20) [reset = 0x00]
            1. Table 87. Open-Load Detect (OLD) Control (OLD_CTRL_2) Register Field Descriptions
          27. 8.6.2.2.27 Open-Load Detect (OLD) Control 3 (OLD_CTRL_3) Register (Address = 0x21) [reset = 0x00]
            1. Table 88. Open-Load Detect (OLD) Control (OLD_CTRL_3) Register Field Descriptions
          28. 8.6.2.2.28 Open Load Detect (OLD) Control 4 (OLD_CTRL_4) Register (Address = 0x22) [reset = 0x00]
            1. Table 89. Open Load Detect (OLD) Control (OLD_CTRL_4) Register Field Descriptions
          29. 8.6.2.2.29 Open Load Detect (OLD) Control 5 (OLD_CTRL_5) Register (Address = 0x23) [reset = 0x00]
            1. Table 90. Open Load Detect (OLD) Control (OLD_CTRL_5) Register Field Descriptions
          30. 8.6.2.2.30 Open Load Detect (OLD) Control 6 (OLD_CTRL_6) Register (Address = 0x24) [reset = 0x00]
            1. Table 91. Open Load Detect (OLD) Control (OLD_CTRL_6) Register Field Descriptions
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Primary Application
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Motor Current Rating
          2. 9.2.1.2.2 Power Dissipation
      2. 9.2.2 Alternative Application
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
          1. 9.2.2.2.1 H-Bridge Requirements for Parallel Operation
      3. 9.2.3 Application Curves
    3. 9.3 Thermal Application
      1. 9.3.1 Power Dissipation
        1. 9.3.1.1 Power Dissipation Due to Device On-State Resistance (RDS(ON))
        2. 9.3.1.2 Power Dissipation Due to Switching Losses
        3. 9.3.1.3 Power Dissipation Due to Quiescent Current
        4. 9.3.1.4 Total Power Dissipation
      2. 9.3.2 PCB Types
      3. 9.3.3 Thermal Parameters
      4. 9.3.4 Transient Thermal
      5. 9.3.5 Device Junction Temperature Estimation
  10. 10Power Supply Recommendations
    1. 10.1 Bulk Capacitance Sizing
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12器件和文档支持
    1. 12.1 文档支持
      1. 12.1.1 相关文档
    2. 12.2 相关链接
    3. 12.3 接收文档更新通知
    4. 12.4 社区资源
    5. 12.5 商标
    6. 12.6 静电放电警告
    7. 12.7 Glossary
  13. 13机械、封装和可订购信息
    1. 13.1 Package Option Addendum
      1. 13.1.1 Packaging Information
      2. 13.1.2 Tape and Reel Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

DRV8912-Q1 and DRV8910-Q1 Register Maps

Table 17. DRV8912-Q1 Register Map

Name 7 6 5 4 3 2 1 0 Type Address
IC_STAT Reserved OTSD OTW OLD OCP UVLO OVP NPOR R 00h
OCP_STAT_1 HB4_HS_OCP HB4_LS_OCP HB3_HS_OCP HB3_LS_OCP HB2_HS_OCP HB2_LS_OCP HB1_HS_OCP HB1_LS_OCP R 01h
OCP_STAT_2 HB8_HS_OCP HB8_LS_OCP HB7_HS_OCP HB7_LS_OCP HB6_HS_OCP HB6_LS_OCP HB5_HS_OCP HB5_LS_OCP R 02h
OCP_STAT_3 HB12_HS_OCP HB12_LS_OCP HB11_HS_OCP HB11_LS_OCP HB10_HS_OCP HB10_LS_OCP HB9_HS_OCP HB9_LS_OCP R 03h
OLD_STAT_1 HB4_HS_OLD HB4_LS_OLD HB3_HS_OLD HB3_LS_OLD HB2_HS_OLD HB2_LS_OLD HB1_HS_OLD HB1_LS_OLD R 04h
OLD_STAT_2 HB8_HS_OLD HB8_LS_OLD HB7_HS_OLD HB7_LS_OLD HB6_HS_OLD HB6_LS_OLD HB5_HS_OLD HB5_LS_OLD R 05h
OLD_STAT_3 HB12_HS_OLD HB12_LS_OLD HB11_HS_OLD HB11_LS_OLD HB10_HS_OLD HB10_LS_OLD HB9_HS_OLD HB9_LS_OLD R 06h
CONFIG_CTRL Reserved IC_ID OCP_REP OTW_REP EXT_OVP CLR_FLT RW 07h
OP_CTRL_1 HB4_HS_EN HB4_LS_EN HB3_HS_EN HB3_LS_EN HB2_HS_EN HB2_LS_EN HB1_HS_EN HB1_LS_EN RW 08h
OP_CTRL_2 HB8_HS_EN HB8_LS_EN HB7_HS_EN HB7_LS_EN HB6_HS_EN HB6_LS_EN HB5_HS_EN HB5_LS_EN RW 09h
OP_CTRL_3 HB12_HS_EN HB12_LS_EN HB11_HS_EN HB11_LS_EN HB10_HS_EN HB10_LS_EN HB9_HS_EN HB9_LS_EN RW 0Ah
PWM_CTRL_1 HB8_PWM HB7_PWM HB6_PWM HB5_PWM HB4_PWM HB3_PWM HB2_PWM HB1_PWM RW 0Bh
PWM_CTRL_2 PWM_CH4_DIS PWM_CH3_DIS PWM_CH2_DIS PWM_CH1_DIS HB12_PWM HB11_PWM HB10_PWM HB9_PWM RW 0Ch
FW_CTRL_1 HB8_FW HB7_FW HB6_FW HB5_FW HB4_FW HB3_FW HB2_FW HB1_FW RW 0Dh
FW_CTRL_2 Reserved HB12_FW HB11_FW HB10_FW HB9_FW RW 0Eh
PWM_MAP_CTRL_1 HB4_PWM_MAP HB3_PWM_MAP HB2_PWM_MAP HB1_PWM_MAP RW 0Fh
PWM_MAP_CTRL_2(1) HB8_PWM_MAP HB7_PWM_MAP HB6_PWM_MAP HB5_PWM_MAP RW 10h(1)
PWM_MAP_CTRL_3 HB12_PWM_MAP HB11_PWM_MAP HB10_PWM_MAP HB9_PWM_MAP RW 11h
PWM_FREQ_CTRL PWM_CH4_FREQ PWM_CH3_FREQ PWM_CH2_FREQ PWM_CH1_FREQ RW 12h
PWM_DUTY_CTRL_1 PWM_DUTY_CH1 RW 13h
PWM_DUTY_CTRL_2 PWM_DUTY_CH2 RW 14h
PWM_DUTY_CTRL_3 PWM_DUTY_CH3 RW 15h
PWM_DUTY_CTRL_4 PWM_DUTY_CH4 RW 16h
SR_CTRL_1 HB8_SR HB7_SR HB6_SR HB5_SR HB4_SR HB3_SR HB2_SR HB1_SR RW 17h
SR_CTRL_2 Reserved HB12_SR HB11_SR HB10_SR HB9_SR RW 18h
OLD_CTRL_1 HB8_OLD_DIS HB7_OLD_DIS HB6_OLD_DIS HB5_OLD_DIS HB4_OLD_DIS HB3_OLD_DIS HB2_OLD_DIS HB1_OLD_DIS RW 19h
OLD_CTRL_2 OLD_REP OLD_OP PL_MODE_EN HB12_OLD_DIS HB11_OLD_DIS HB10_OLD_DIS HB9_OLD_DIS RW 1Ah
OLD_CTRL_3 OCP_DEG OLD_NEG_EN HB12_LOLD_EN HB11_LOLD_EN HB10_LOLD_EN HB9_LOLD_EN RW 1Bh
OLD_CTRL_4 HB8_LOLD_EN HB7_LOLD_EN HB6_LOLD_EN HB5_LOLD_EN HB4_LOLD_EN HB3_LOLD_EN HB2_LOLD_EN HB1_LOLD_EN RW 24h
After this register address, the functions are similar between DRV8912-Q1 and DRV8910-Q1. However, DRV8908-Q1, DRV8906-Q1, and DRV8904-Q1 have different functions for these addresses.

Table 18. DRV8910-Q1 Register Map

Name 7 6 5 4 3 2 1 0 Type Address
IC_STAT Reserved OTSD OTW OLD OCP UVLO OVP NPOR R 00h
OCP_STAT_1 HB4_HS_OCP HB4_LS_OCP HB3_HS_OCP HB3_LS_OCP HB2_HS_OCP HB2_LS_OCP HB1_HS_OCP HB1_LS_OCP R 01h
OCP_STAT_2 HB8_HS_OCP HB8_LS_OCP HB7_HS_OCP HB7_LS_OCP HB6_HS_OCP HB6_LS_OCP HB5_HS_OCP HB5_LS_OCP R 02h
OCP_STAT_3 Reserved HB10_HS_OCP HB10_LS_OCP HB9_HS_OCP HB9_LS_OCP R 03h
OLD_STAT_1 HB4_HS_OLD HB4_LS_OLD HB3_HS_OLD HB3_LS_OLD HB2_HS_OLD HB2_LS_OLD HB1_HS_OLD HB1_LS_OLD R 04h
OLD_STAT_2 HB8_HS_OLD HB8_LS_OLD HB7_HS_OLD HB7_LS_OLD HB6_HS_OLD HB6_LS_OLD HB5_HS_OLD HB5_LS_OLD R 05h
OLD_STAT_3 Reserved HB10_HS_OLD HB10_LS_OLD HB9_HS_OLD HB9_LS_OLD R 06h
CONFIG_CTRL Reserved IC_ID OCP_REP OTW_REP EXT_OVP CLR_FLT RW 07h
OP_CTRL_1 HB4_HS_EN HB4_LS_EN HB3_HS_EN HB3_LS_EN HB2_HS_EN HB2_LS_EN HB1_HS_EN HB1_LS_EN RW 08h
OP_CTRL_2 HB8_HS_EN HB8_LS_EN HB7_HS_EN HB7_LS_EN HB6_HS_EN HB6_LS_EN HB5_HS_EN HB5_LS_EN RW 09h
OP_CTRL_3 Reserved HB10_HS_EN HB10_LS_EN HB9_HS_EN HB9_LS_EN RW 0Ah
PWM_CTRL_1 HB8_PWM HB7_PWM HB6_PWM HB5_PWM HB4_PWM HB3_PWM HB2_PWM HB1_PWM RW 0Bh
PWM_CTRL_2 PWM_CH4_DIS PWM_CH3_DIS PWM_CH2_DIS PWM_CH1_DIS Reserved HB10_PWM HB9_PWM RW 0Ch
FW_CTRL_1 HB8_FW HB7_FW HB6_FW HB5_FW HB4_FW HB3_FW HB2_FW HB1_FW RW 0Dh
FW_CTRL_2 Reserved HB10_FW HB9_FW RW 0Eh
PWM_MAP_CTRL_1 HB4_PWM_MAP HB3_PWM_MAP HB2_PWM_MAP HB1_PWM_MAP RW 0Fh
PWM_MAP_CTRL_2(1) HB8_PWM_MAP HB7_PWM_MAP HB6_PWM_MAP HB5_PWM_MAP RW 10h(1)
PWM_MAP_CTRL_3 Reserved HB10_PWM_MAP HB9_PWM_MAP RW 11h
PWM_FREQ_CTRL PWM_CH4_FREQ PWM_CH3_FREQ PWM_CH2_FREQ PWM_CH1_FREQ RW 12h
PWM_DUTY_CTRL_1 PWM_DUTY_CH1 RW 13h
PWM_DUTY_CTRL_2 PWM_DUTY_CH2 RW 14h
PWM_DUTY_CTRL_3 PWM_DUTY_CH3 RW 15h
PWM_DUTY_CTRL_4 PWM_DUTY_CH4 RW 16h
SR_CTRL_1 HB8_SR HB7_SR HB6_SR HB5_SR HB4_SR HB3_SR HB2_SR HB1_SR RW 17h
SR_CTRL_2 Reserved HB10_SR HB9_SR RW 18h
OLD_CTRL_1 HB8_OLD_DIS HB7_OLD_DIS HB6_OLD_DIS HB5_OLD_DIS HB4_OLD_DIS HB3_OLD_DIS HB2_OLD_DIS HB1_OLD_DIS RW 19h
OLD_CTRL_2 OLD_REP OLD_OP PL_MODE_EN Reserved HB10_OLD_DIS HB9_OLD_DIS RW 1Ah
OLD_CTRL_3 OCP_DEG OLD_NEG_EN Reserved HB10_LOLD_EN HB9_LOLD_EN RW 1Bh
OLD_CTRL_4 HB8_LOLD_EN HB7_LOLD_EN HB6_LOLD_EN HB5_LOLD_EN HB4_LOLD_EN HB3_LOLD_EN HB2_LOLD_EN HB1_LOLD_EN RW 24h
After this register address, the register functions are similar between DRV8912-Q1 and DRV8910-Q1. However, DRV8908-Q1, DRV8906-Q1, and DRV8904-Q1 have different functions for these addresses.