TPS659128
- Four step-down converters:
- Input voltage (VIN) range from 2.7 V to 5.5 V
- Power save mode at light load current
- Output voltage accuracy in PWM mode ±2%
- Typical 26-µA quiescent current per converter
- Dynamic voltage scaling
- 100% duty cycle for lowest dropout
- Ten LDOs:
- 8 general-purpose LDOs
- Output voltage range from 0.8 V to 3.3 V
- Typical 32-µA quiescent current per LDO
- 2 low-noise RF-LDOs
- Output voltage range from 1.6 V to 3.3 V
- Preregulation support by separate power inputs
- Eco-mode™ control scheme
- VIN range of LDOs respective to the
following voltage ranges:
- 1.8 V to 3.6 V
- 3 V to 5.5 V
- Three LED drivers:
- Internal dimming using I2C
- Up to 20 mA per current sink
- Thermal monitoring
- High temperature warning
- Thermal shutdown
- Bypass switch
- Used with DCDC4 in applications powering a Radio Frequency Power Amplifier (RF-PA)
- Interface
- I2C interface
- Power I2C interface for Dynamic Voltage Scaling (DVS)
- Serial Peripheral Interface (SPI)
- 32-kHz RC oscillator
- Undervoltage lockout, battery fault comparator, and long button-press detection
- 3.6-mm × 3.6-mm DSBGA package with 0.4-mm pitch
The TPS659128x device provides four configurable step-down converters with up to 2.5-A output current and ten LDO regulators for external use. These LDOs can be supplied from either a battery or a preregulated supply. Each specific part number has a different factory programmed power-up and power-down sequence.
The TPS659128x device integrates a 32-kHz RC oscillator to sequence all resources during power up or power down. All LDOs and DC-DC converters can be controlled by an I2C or SPI interface or basic enable pins after boot. Additionally, a voltage-scaling interface allows for transitioning the DC-DC converters to a different voltage through I2C or basic roof-floor control. Three LED drivers with an advanced dimming feature are integrated inside the device. General-purpose input-output (GPIO) functionality is multiplexed with various pins, including LED pins, ENx pins, and SPI pins when not used. Each GPIO can be configured as part of the power-up sequence to control external resources. One SLEEP pin enables switching between the active mode and preprogrammed sleep mode for power optimization. The TPS659128x device comes in a 9-pin × 9-pin DSBGA package (3.6 mm × 3.6 mm) with a 0.4-mm pitch.
技術文件
| 重要文件 | 類型 | 標題 | 格式選項 | 下載最新的英文版本 | 日期 | |
|---|---|---|---|---|---|---|
| * | 資料表 | TPS659128 PMU for Processor Power datasheet (Rev. A) | 2021/6/10 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
TPS65912SW-LINUX — 適用於 TPS65912 的 Linux 驅動程式
The Linux driver supports the TPS65912 Video ADC. The Linux driver supports communication through the I2C and SPI bus and interfaces with the Regulator sub-system.
Linux Mainline Status
Available in Linux Main line: Yes
Available through git.ti.com: N/A
Supported Devices:
- tps65912
Linux Source Files
The (...)
IPG-UI — IPG-UI EVM GUI (Windows Installer)
IPG-UI GUI 可用於配置多部 PMIC 裝置，以評估這些裝置的功能和性能。 此 GUI 使用 Web 型技術建立，支援使用 USB2ANY 轉接器電路板與 EVM 硬體互動。提供 USB2ANY Explorer，允許將 USB2ANY 轉接器電路板上的韌體更新到所需的版本 (2.7.0.0 或更高版本)。
IPG-UI-LINUX — IPG-UI EVM GUI (Linux Installer)
IPG-UI GUI 可用於配置多部 PMIC 裝置，以評估這些裝置的功能和性能。 此 GUI 使用 Web 型技術建立，支援使用 USB2ANY 轉接器電路板與 EVM 硬體互動。提供 USB2ANY Explorer，允許將 USB2ANY 轉接器電路板上的韌體更新到所需的版本 (2.7.0.0 或更高版本)。
IPG-UI-OSX — IPG-UI EVM GUI (OSX Installer)
IPG-UI GUI 可用於配置多部 PMIC 裝置，以評估這些裝置的功能和性能。 此 GUI 使用 Web 型技術建立，支援使用 USB2ANY 轉接器電路板與 EVM 硬體互動。提供 USB2ANY Explorer，允許將 USB2ANY 轉接器電路板上的韌體更新到所需的版本 (2.7.0.0 或更高版本)。
SLVC435 — TPS65912xEVM Software – Legacy
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| DSBGA (YFF) | 81 | Ultra Librarian |
訂購與品質
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。