TPS25830A-Q1
- AEC-Q100 qualified for automotive applications:
- Temperature grade 1: –40°C to +125°C, TA
- HBM ESD classification level H2
- CDM ESD classification level C5
- Synchronous buck DC/DC regulator
- Input voltage range: 4.5 V to 36 V
- Output current: 3.5 A
- 5.1-V output voltage with ±1% accuracy
- Current mode control
- Adjustable frequency: 300 kHz to 2.2 MHz
- Frequency synchronization to external clock
- FPWM with spread-spectrum dithering
- Internal compensation for ease of use
- Compliant to USB-IF standards
- USB Type-C® rev 1.3
- CC logic, VCONN source and discharge
- USB cable polarity detection (POL)
- CDP/SDP mode per USB BC1.2
- MFI over-current limit compliant
- USB Type-C® rev 1.3
- Optimized for USB power and communication
- User-programmable USB current limit
- Cable droop compensation up to 1.5 V
- High bandwidth data switches on DP and DM
- Client mode for USB firmware update
- Integrated protection
- VBUS short-to-VBAT protection
- DP_IN, DM_IN, CCx short-to-VBAT (TPS25830A-Q1 only)
- DP_IN, DM_IN, CCx short-to-VBUS
- DP_IN, DM_IN, CCx IEC 61000-4-2 rated
- ±8-kV contact and ±15-kV air discharge
- Fault flag reports
- 32-pin QFN package with wettable flank
The TPS2583xA-Q1 is a USB Type-C and BC1.2 charging port controller that includes a synchronous DC/DC converter. With cable droop compensation, the VBUS voltage remains constant regardless of load current, ensuring connected portable devices charge at optimal current and voltage.
The TPS2583xA-Q1 includes high bandwidth analog switches for DP and DM pass-through.
The TPS25830A-Q1 also integrates short-to-battery protection on VBUS, CC1, CC2, DM_IN and DP_IN pins (up to 18-V support). The TPS25832A-Q1 does not support data line (CC and Dx) short to VBAT protection.
The synchronous buck regulator operates with current mode control and is internally compensated to simplify design. A resistor on the RT pin sets the switching frequency between 300 kHz and 2.2 MHz. Operating below 400 kHz results in better system efficiency. Operation above 2.1 MHz avoids the AM radio bands and allows for use of a smaller inductor.
The TPS2583xA-Q1 integrates standard USB Type-C port controller functionality including Configuration Channel (CC) logic for 3-A and 1.5-A current advertisement. Battery Charging (Rev. 1.2) integration provides the required electrical signatures necessary for non-Type-C, legacy USB devices which use USB data line signaling to determine USB port current sourcing capabilities.
A precision current sense amplifier is included for user programmable cable droop compensation and current limit tuning. Cable compensation aids portable devices in charging at optimum current and voltage under heavy loads by changing the buck regulator output voltage linearly with load current to counteract the voltage drop due to wire resistance in automotive cabling. The VBUS voltage measured at a connected portable device remains approximately constant, regardless of load current, allowing the portable device’s battery charger to work optimally.
The USB specifications require current limiting of USB charging ports, but give system designers reasonable flexibility to choose overcurrent protection levels based on system requirements. The TPS2583xA-Q1 uses a novel two-threshold current limit circuit allowing system designers to either program average current limit protection of the buck regulator, or optionally, current limit using an external NMOS between the CSN/OUT and BUS pins. The NFET implementation enables the TPS2583xA-Q1 buck regulator to supply a 5-V output for other loads during an overcurrent fault condition on the USB port. Also, the current limit methodology TPS2583xA-Q1 use can meet latest MFI requirement.
TPS2583xA-Q1 Integrated protection features include cycle-by-cycle current limit, hiccup short-circuit protection, undervoltage lockout, VBUS overvoltage and overcurrent, CC overvoltage and overcurrent, data line (Dx) short to VBUS and VBAT, and die overtemperature protection.
The TPS25830A-Q1 includes high bandwidth analog switches for DP and DM pass-through, and support data line (Dx and CC) short-to-VBAT protection. The TPS25832A-Q1 does not support data line (Dx and CC) short-to-VBAT protection.
您可能會感興趣的類似產品
功能相似於所比較的產品。
技術文件
| 重要文件 | 類型 | 標題 | 格式選項 | 下載最新的英文版本 | 日期 | |
|---|---|---|---|---|---|---|
| * | 資料表 | TPS2583xA-Q1 Automotive USB Type-C® and BC1.2 5-V 3.5-A Output, 36-V Input Synch datasheet (Rev. A) | PDF | HTML | 2022/3/21 | ||
| 應用說明 | TPS25830, TPS25831-Q1, and TPS25840-Q1 Short-to-Battery Application (Rev. A) | PDF | HTML | 2023/6/2 | |||
| 功能安全資訊 | TPS25830A-Q1 Functional Safety FIT Rate, FMD and Pin FMA | PDF | HTML | 2022/5/11 | |||
| Application brief | TI Automotive USB Charging Port Solution | PDF | HTML | 2022/2/18 | |||
| 應用說明 | How to Improve an Eye Diagram With the TPS25840-Q1 Device Using a Long USB Cable | 2020/1/10 | ||||
| 應用說明 | Ground Shift Phenomenon Recommendation of TPS2583x | PDF | HTML | 2019/12/2 | |||
| 應用說明 | Loop Characteristic Evaluation and Optimization of TPS2583x | PDF | HTML | 2019/12/2 | |||
| 技術文章 | How to avoid the pain of a discharged device | PDF | HTML | 2019/8/21 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
TPS2583XAQ1EVM-147 — 適用 BC 1.2 和 USB Type-C® 埠控制器的 TPS2583xA-Q1 評估模組
PMP30338 — 車用雙埠 USB Type-C 參考設計 (2x 15 W)
PMP40544 — 符合 3-m USB-IF 近端規範的車用 USB Type-A 充電器參考設計
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| VQFN (RHB) | 32 | Ultra Librarian |
訂購與品質
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。