首頁 音訊、觸覺和壓電 音訊放大器 車用音訊放大器
首頁
音訊、觸覺和壓電
音訊放大器
車用音訊放大器

TPA6404-Q1

現行

具負載突降的車用 45W、2MHz、4 通道 4.5 至 18V 電源類比輸入 D 類音訊放大器

立即訂購
產品規格表

TPA6404-Q1

現行
產品規格表 立即訂購

產品詳細資料

Output power (W) 45 Power stage supply (max) (V) 18 Power stage supply (min) (V) 4.5 Speaker channels (max) 4 Features thermal pad up Audio input type Analog Input Control interface I2C THD + N at 1 kHz (%) 0.01 Switching frequency (max) (Hz) 2100000 Output noise voltage (µV) 42 Rating Automotive Operating temperature range (°C) -40 to 125
Output power (W) 45 Power stage supply (max) (V) 18 Power stage supply (min) (V) 4.5 Speaker channels (max) 4 Features thermal pad up Audio input type Analog Input Control interface I2C THD + N at 1 kHz (%) 0.01 Switching frequency (max) (Hz) 2100000 Output noise voltage (µV) 42 Rating Automotive Operating temperature range (°C) -40 to 125
HSSOP (DKQ) 56 190.647 mm² 18.42 x 10.35
  • Advanced load diagnostics
    • AC diagnostic for tweeter detection with impedance and phase response
    • Integrated sine wave generator
  • Easy to meet CISPR25-L5 EMC specification
  • AEC-Q100 Qualified for automotive applications:
    • Temperature Grade 1: –40°C to 125°C TA
    • Device HBM ESD classification level: 3A
    • Device CDM ESD classification level: C4B
  • Audio Inputs
    • 4 Channel differential analog input
    • Four I2C-controlled gain options
    • High input impedance for low value AC-coupling capacitor
  • Audio outputs
    • Four-channel Bridge-tied load (BTL), with option of parallel BTL (PBTL)
    • Up to 2.1 MHz Output switching frequency
    • 27 W, 10% THD into 4Ω at 14.4V
    • 45W, 10% THD into 2Ω at 14.4V
    • 85W, 10% THD into 1Ω at 14.4V PBTL
  • Audio performance into 4Ω at 14.4V, 1kHz
    • THD+N < 0.01%
    • 42µVRMS Output noise
    • - 90dB Crosstalk
  • Load Diagnostics
    • Output open and shorted load
    • Output-to-battery or ground shorts
    • Line output detection up to 6kΩ
    • Runs without input clocks
  • Protection
    • Output current limiting
    • Output short protection
    • 40V Load dump
    • Fortuitous Open ground and power tolerant
    • DC Offset
    • Over temperature
    • Undervoltage and overvoltage
  • General operation
    • 4.5V to 18V supply voltage
    • I2C Control With 4 Address Options
    • Clip Detection and Thermal Foldback
  • Advanced load diagnostics
    • AC diagnostic for tweeter detection with impedance and phase response
    • Integrated sine wave generator
  • Easy to meet CISPR25-L5 EMC specification
  • AEC-Q100 Qualified for automotive applications:
    • Temperature Grade 1: –40°C to 125°C TA
    • Device HBM ESD classification level: 3A
    • Device CDM ESD classification level: C4B
  • Audio Inputs
    • 4 Channel differential analog input
    • Four I2C-controlled gain options
    • High input impedance for low value AC-coupling capacitor
  • Audio outputs
    • Four-channel Bridge-tied load (BTL), with option of parallel BTL (PBTL)
    • Up to 2.1 MHz Output switching frequency
    • 27 W, 10% THD into 4Ω at 14.4V
    • 45W, 10% THD into 2Ω at 14.4V
    • 85W, 10% THD into 1Ω at 14.4V PBTL
  • Audio performance into 4Ω at 14.4V, 1kHz
    • THD+N < 0.01%
    • 42µVRMS Output noise
    • - 90dB Crosstalk
  • Load Diagnostics
    • Output open and shorted load
    • Output-to-battery or ground shorts
    • Line output detection up to 6kΩ
    • Runs without input clocks
  • Protection
    • Output current limiting
    • Output short protection
    • 40V Load dump
    • Fortuitous Open ground and power tolerant
    • DC Offset
    • Over temperature
    • Undervoltage and overvoltage
  • General operation
    • 4.5V to 18V supply voltage
    • I2C Control With 4 Address Options
    • Clip Detection and Thermal Foldback

The TPA6404-Q1 device is a four-channel analog-input Class-D audio amplifier that implements a 2.1MHz PWM switching frequency that enables a cost optimized solution in a very small 4.5cm2 PCB size, full operation down to 4.5V for start/stop events, and exceptional sound quality with up to 100kHz audio bandwidth.

The TPA6404-Q1 Class-D audio amplifier has an optimal design for use in entry level automotive head units that provide analog audio input signals as part of their system design.

The Class-D topology dramatically improves efficiency over traditional linear amplifier solutions.

The output switching frequency operates above the AM band, which eliminates the AM band interference and reduces the output filter size and cost.

The device is offered in a 56 pin HSSOP package with the exposed thermal pad up.

The TPA6404-Q1 device is a four-channel analog-input Class-D audio amplifier that implements a 2.1MHz PWM switching frequency that enables a cost optimized solution in a very small 4.5cm2 PCB size, full operation down to 4.5V for start/stop events, and exceptional sound quality with up to 100kHz audio bandwidth.

The TPA6404-Q1 Class-D audio amplifier has an optimal design for use in entry level automotive head units that provide analog audio input signals as part of their system design.

The Class-D topology dramatically improves efficiency over traditional linear amplifier solutions.

The output switching frequency operates above the AM band, which eliminates the AM band interference and reduces the output filter size and cost.

The device is offered in a 56 pin HSSOP package with the exposed thermal pad up.
filter 尋找其它 車用音訊放大器
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 4
重要文件 類型 標題 格式選項 日期
* Data sheet TPA6404-Q1 45W,​​​ 2MHz Analog Input 4 -Channel Automotive Class-D Audio Amplifier with Load Dump Protection and I2 C Diagnostics datasheet (Rev. B) PDF | HTML 2025年 1月 15日
Application brief Diagnostics and Protections in Automotive Audio Systems (Rev. A) 2019年 9月 24日
Application note Inductor Selection Guide for 2.1 MHz Class-D Amplifiers (Rev. A) 2019年 9月 5日
Technical article Why you should use a Class-D audio amplifier in your automotive infotainment syste PDF | HTML 2018年 1月 8日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPA6404Q1EVM — TPA6404-Q1 50W、2MHz 類比輸入四通道車用 D 類音訊放大器評估模組

TPA6404Q1EVM 評估模組 (EVM) 展示了德州儀器的 TPA6404-Q1 積體電路。TPA6404-Q1 裝置是一款四通道類比輸入 D 類音訊放大器，採用 2.1MHz PWM 切換頻率，可在非常小的 PCB 尺寸內實現成本最佳化的解決方案，在啟動/停止事件時可在低至 4.5V 的電壓下完全運作，音訊頻寬高達 40kHz，音質卓越。

此 TPA6404Q1EVM 支援 4 個 BTL 輸出通道，4 個差動輸入，以及適用 GUI 驅動評估與診斷的板載 USB-I2C 控制器。TPA6404Q1EVM 為完整的車用 D (...)

使用指南: PDF
TI.com 無法提供
應用軟體及架構

PUREPATHCONSOLE — PurePath™ Console graphical development suite for audio system design and development

PurePath™ Console is a highly integrated and easy-to-use audio development suite designed specifically to simplify the evaluation, configuration and debug process associated with the development of audio products. Watch how easy it is to use the PurePath™ Console 3 software.

PurePath Console’s (...)
支援產品和硬體

支援產品和硬體
要求
模擬型號

TPA6404-Q1 IBIS Model

SLOM440.ZIP (23 KB) - IBIS Model
下載
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI 是有助於評估類比電路功能的設計和模擬環境。這款全功能設計和模擬套件使用 Cadence® 的類比分析引擎。PSpice for TI 包括業界最大的模型庫之一，涵蓋我們的類比和電源產品組合，以及特定類比行為模型，且使用無需支付費用。

PSpice for TI 設計和模擬環境可讓您使用其內建函式庫來模擬複雜的混合訊號設計。在進行佈局和製造之前，建立完整的終端設備設計和解決方案原型，進而縮短上市時間並降低開發成本。 

在 PSpice for TI 設計與模擬工具中，您可以搜尋 TI (...)
要求
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HSSOP (DKQ) 56 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片