首頁 介面 I2C、I3C 與 SPI IC I2C 與 I3C 位準移位器、緩衝器與集線器
首頁
介面
I2C、I3C 與 SPI IC
I2C 與 I3C 位準移位器、緩衝器與集線器

TCA9406

現行

具內置推拉式電阻的 2 位元雙向 1MHz I2C/SMBus 匯流排電壓位準轉換器

立即訂購
產品規格表

TCA9406

現行
產品規格表 立即訂購

產品詳細資料

Features Enable pin Protocols I2C Frequency (max) (MHz) 1 VCCA (min) (V) 1.65 VCCA (max) (V) 3.6 VCCB (min) (V) 2.3 VCCB (max) (V) 5.5 Supply restrictions VCCA <= VCCB Rating Catalog Operating temperature range (°C) -40 to 85
Features Enable pin Protocols I2C Frequency (max) (MHz) 1 VCCA (min) (V) 1.65 VCCA (max) (V) 3.6 VCCB (min) (V) 2.3 VCCB (max) (V) 5.5 Supply restrictions VCCA <= VCCB Rating Catalog Operating temperature range (°C) -40 to 85
DSBGA (YZP) 8 2.8125 mm² 2.25 x 1.25 SSOP (DCT) 8 11.8 mm² 2.95 x 4 VSSOP (DCU) 8 6.2 mm² 2 x 3.1
  • 2-Bit Bidirectional Translator for SDA and SCL Lines in I2C Applications
  • Provides Bidirectional Voltage Translation With No Direction Pin
  • High-Impedance Output SCL_A, SDA_A, SCL_B, SDA_B Pins When OE = Low or VCC = 0 V
  • Internal 10-kΩ Pullup Resistor on All SDA and SCL Pins
  • 1.65 V to 3.6 V on A port and 2.3 V to 5.5 V on B port (VCCA  ≤ VCCB)
  • VCC Isolation Feature: If Either VCC Input Is at GND, Both Ports Are in the High-Impedance State
  • No Power-Supply Sequencing Required: Either VCCA or VCCB Can Be Ramped First
  • Low Ioff of 2 µA When Either VCCA or VCCB = 0 V
  • OE Input Can Be Tied Directly to VCCA Or Controlled By GPIO
  • Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
  • ESD Protection Exceeds JESD 22
    • A Port
      • 2500-V Human-Body Model (A114-B)
      • 250-V Machine Model (A115-A)
      • 1500-V Charged-Device Model (C101)
    • B Port
      • 8-kV Human-Body Model (A114-B)
      • 250-V Machine Model (A115-A)
      • 1500-V Charged-Device Model (C101)
  • 2-Bit Bidirectional Translator for SDA and SCL Lines in I2C Applications
  • Provides Bidirectional Voltage Translation With No Direction Pin
  • High-Impedance Output SCL_A, SDA_A, SCL_B, SDA_B Pins When OE = Low or VCC = 0 V
  • Internal 10-kΩ Pullup Resistor on All SDA and SCL Pins
  • 1.65 V to 3.6 V on A port and 2.3 V to 5.5 V on B port (VCCA  ≤ VCCB)
  • VCC Isolation Feature: If Either VCC Input Is at GND, Both Ports Are in the High-Impedance State
  • No Power-Supply Sequencing Required: Either VCCA or VCCB Can Be Ramped First
  • Low Ioff of 2 µA When Either VCCA or VCCB = 0 V
  • OE Input Can Be Tied Directly to VCCA Or Controlled By GPIO
  • Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
  • ESD Protection Exceeds JESD 22
    • A Port
      • 2500-V Human-Body Model (A114-B)
      • 250-V Machine Model (A115-A)
      • 1500-V Charged-Device Model (C101)
    • B Port
      • 8-kV Human-Body Model (A114-B)
      • 250-V Machine Model (A115-A)
      • 1500-V Charged-Device Model (C101)

The TCA9406 is a 2-bit bidirectional I2C and SMBus voltage-level translator with an output enable (OE) input. It is operational from 1.65 V to 3.6 V on the A-side, referenced toVCCA, and from 2.3 V to 5.5 V on the B-side, referenced to VCCB. This allows the device to interface between lower and higher logic signal levels at any of the typical 1.8-V, 2.5-V, 3.3-V, and
5-V supply rails.

The OE input pin is referenced to VCCA, can be tied directly to VCCA, but it is also 5.5-V tolerant. The OE pin can also be controlled and set to a logic low to place all the SCL and SDA pins in a high-impedance state, which significantly reduces the quiescent current consumption.

Under normal I2C and SMBus operation or other open-drain configurations, the TCA9406 can support up to 2 Mbps; therefore, it is compatible with standard I2C speeds where the frequency of SCL is 100 kHz (Standard-mode), 400 kHz (Fast-mode), or 1 MHz (Fast-mode Plus). The device can also be used as a general purpose level translator, and when the A- and B-side ports are both driven with push-pull devices the TCA9406 can support up to 24 Mbps.

The TCA9406 features internal 10-kΩ pullup resistors on SCL_A, SDA_A, SCL_B, and SDA_B. Additional external pullup resistors can be added to the bus to reduce the total pullup resistance and speed up rising edges.

The TCA9406 is a 2-bit bidirectional I2C and SMBus voltage-level translator with an output enable (OE) input. It is operational from 1.65 V to 3.6 V on the A-side, referenced toVCCA, and from 2.3 V to 5.5 V on the B-side, referenced to VCCB. This allows the device to interface between lower and higher logic signal levels at any of the typical 1.8-V, 2.5-V, 3.3-V, and
5-V supply rails.

The OE input pin is referenced to VCCA, can be tied directly to VCCA, but it is also 5.5-V tolerant. The OE pin can also be controlled and set to a logic low to place all the SCL and SDA pins in a high-impedance state, which significantly reduces the quiescent current consumption.

Under normal I2C and SMBus operation or other open-drain configurations, the TCA9406 can support up to 2 Mbps; therefore, it is compatible with standard I2C speeds where the frequency of SCL is 100 kHz (Standard-mode), 400 kHz (Fast-mode), or 1 MHz (Fast-mode Plus). The device can also be used as a general purpose level translator, and when the A- and B-side ports are both driven with push-pull devices the TCA9406 can support up to 24 Mbps.

The TCA9406 features internal 10-kΩ pullup resistors on SCL_A, SDA_A, SCL_B, and SDA_B. Additional external pullup resistors can be added to the bus to reduce the total pullup resistance and speed up rising edges.
filter 尋找其它 I2C 與 I3C 位準移位器、緩衝器與集線器
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 5
類型 標題 日期
* Data sheet TCA9406 2-Bit Bidirectional 1-MHz, I2C Bus and SMBus Voltage-Level Translator With 8-kV HBM ESD datasheet (Rev. G) PDF | HTML 2018年 11月 29日
Application note Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) PDF | HTML 2024年 7月 3日
Application note Understanding the I2C Bus PDF | HTML 2015年 6月 30日
Application note Maximum Clock Frequency of I2C Bus Using Repeaters 2015年 5月 15日
Application note I2C Bus Pull-Up Resistor Calculation PDF | HTML 2015年 2月 13日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

DS90UB9702-Q1EVM — DS90UB9702-Q1 評估模組

DS90UB9702-Q1EVM 評估模組 (EVM) 是一款功能板設計，用於評估 DS90UB9702-Q1 FPD-Link IV 解串列集線器。DS90UB9702-Q1 是一款多功能解串器，能夠使用 FPD-Link III 和 FPD-Link IV 串聯器從多達四個獨立視訊來源接收數據。與 DS90UB971-Q1 串聯器配對時，DS90UB9702-Q1 可以接收來自 8MP+ 成像儀的高色深數據。它具有兩個獨立的 MIPI DPHY CSI-2 輸出埠和一個複製 CSI-2 埠，每個埠有四個可用通道，每個通道支援最高 2.5Gbps 的速度。此裝置也支援 4x CML (...)
要求
開發板

TCA9406EVM — 具有上升時間加速器的 TCA9406 I2C 轉換器評估模組

此 EVM 可用於評估 DCU 封裝中的 TCA9406 產品。I2C 匯流排可透過 SDA_A、SCL_A、SDA_B 和 SCL_B 測試點輕鬆存取，並採用對稱配置以提供最佳效能。所有 IC 訊號都可透過測試點連接使用。
使用指南: PDF
TI.com 無法提供
設計工具

I2C-DESIGNER — I2C 設計工具

使用 I2C 設計工具快速解決 I2C 設計中在定址、電壓位準和頻率方面的衝突。輸入主裝置和從屬裝置的參數，自動產生 I2C 樹狀結構，或輕鬆建置自訂解決方案。此工具將協助設計人員節省時間並符合 I2C 標準，提供關於偵錯缺失確認、選擇上拉電阻以及滿足 I2C 匯流排最大電容負載的指導。 
在雲端評估
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI 是有助於評估類比電路功能的設計和模擬環境。這款全功能設計和模擬套件使用 Cadence® 的類比分析引擎。PSpice for TI 包括業界最大的模型庫之一，涵蓋我們的類比和電源產品組合，以及特定類比行為模型，且使用無需支付費用。

PSpice for TI 設計和模擬環境可讓您使用其內建函式庫來模擬複雜的混合訊號設計。在進行佈局和製造之前，建立完整的終端設備設計和解決方案原型，進而縮短上市時間並降低開發成本。 

在 PSpice for TI 設計與模擬工具中，您可以搜尋 TI (...)
要求
模擬工具

TINA-TI — 基於 SPICE 的類比模擬程式

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
使用指南: PDF
View Options
參考設計

TIDA-01572 — 數位輸入、D 類、IV 感測音訊放大器的立體聲評估模組參考設計

此參考設計提供高性能立體聲道音訊子系統，可在 PC 應用中使用。其以 4.5V 至 16V 的單電源供電運作，並搭載 TAS2770 這款數位輸入 D 類音訊放大器；此放大器可提供出色的雜訊和失真性能，並提供 WCSP 和 QFN 兩種封裝。該設計還包括 TL760M33 和 TPS73618 這兩個低壓差固定電壓穩壓器，分別產生所需的 3.3V 和 1.8V 系統軌。此參考設計的多用途數位輸入介面可支援多種輸入格式，同時提供電壓與電流感測、供應電壓 (VBAT) 及溫度的輸出資料。此參考設計也包括多工處理，可將多個輸入來源連接至數位輸入。此外，TAS2770 整合了可追蹤 VBAT (...)
Design guide: PDF
電路圖: PDF
參考設計

TIDA-00609 — 自我啟動音訊系統

The purpose of this reference design is to provide hardware and software tools that can be used as reference for audio systems. The new revision of the PurePath™ Console Motherboard (Rev F) adds stand-alone self-booting capabilities to allow making compelling demos with any evaluation module (...)
Test report: PDF
電路圖: PDF
封裝 針腳 CAD 符號、佔位空間與 3D 模型
DSBGA (YZP) 8 Ultra Librarian
SSOP (DCT) 8 Ultra Librarian
VSSOP (DCU) 8 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片