首頁 音訊、觸覺和壓電 音訊放大器 車用音訊放大器
首頁
音訊、觸覺和壓電
音訊放大器
車用音訊放大器

TAS6422E-Q1

現行

車用 75W、2MHz、2 通道 4.5V 至 26.4V 數位輸入 D 類音訊放大器

立即訂購
產品規格表

TAS6422E-Q1

現行
產品規格表 立即訂購

產品詳細資料

Output power (W) 75 Power stage supply (max) (V) 26.4 Power stage supply (min) (V) 4.5 Speaker channels (max) Stereo Features thermal pad up Audio input type Digital Input Control interface I2C THD + N at 1 kHz (%) 0.02 Switching frequency (max) (Hz) 2100000 Output noise voltage (µV) 42 Sampling rate (max) (Hz) 96000 Rating Automotive Operating temperature range (°C) -40 to 125
Output power (W) 75 Power stage supply (max) (V) 26.4 Power stage supply (min) (V) 4.5 Speaker channels (max) Stereo Features thermal pad up Audio input type Digital Input Control interface I2C THD + N at 1 kHz (%) 0.02 Switching frequency (max) (Hz) 2100000 Output noise voltage (µV) 42 Sampling rate (max) (Hz) 96000 Rating Automotive Operating temperature range (°C) -40 to 125
HSSOP (DKQ) 56 190.647 mm² (18.42 mm × 10.35 mm)
  • AEC-Q100 Qualified for automotive applications
    • Temperature grade 1: –40°C to +125°C TA
  • Advanced load diagnostics
    • DC Diagnostics run without input clocks
    • AC Diagnostic for tweeter detection with impedance and phase response
  • Easily meets CISPR25-L5 EMC specifications
  • Audio inputs
    • 2 Channel I2S or 4/8-channel TDM input
    • Input sample rates: 44.1 kHz, 48 kHz, 96 kHz
    • Input formats: 16-bit to 32-bit I2S, and TDM
  • Audio Outputs
    • Two-channel bridge-tied load (BTL)
    • Single-channel parallel BTL (PBTL)
    • Up to 2.1 MHz output switching frequency
    • 45 W, 10% THD+N Into 2 Ω at 14.4 V BTL
    • 75 W, 10% THD+N Into 4 Ω at 25 V BTL
    • 150W, 10% THD+N Into 2 Ω at 25V PBTL
  • Audio performance into 4 Ω at 14.4 V BTL
    • THD+N < 0.02% at 1 W
    • 42 µVRMS output noise
    • –90 dB crosstalk
  • Load diagnostics
    • Output open and shorted load
    • Output-to-battery or ground shorts
    • Line output detection up to 6 kΩ
    • Host-independent operation
  • Protection
    • Output current limiting and short protection
    • 40 V Load dump
    • Open ground and power tolerant
    • DC offset
    • Over-temperature
    • Undervoltage and overvoltage
  • General Operation
    • 4.5 V to 18 V supply voltage
    • I2C Control with 4 address options
    • Latched & Non-Latched Clip Detect
    • Enhanced EMI Management
  • AEC-Q100 Qualified for automotive applications
    • Temperature grade 1: –40°C to +125°C TA
  • Advanced load diagnostics
    • DC Diagnostics run without input clocks
    • AC Diagnostic for tweeter detection with impedance and phase response
  • Easily meets CISPR25-L5 EMC specifications
  • Audio inputs
    • 2 Channel I2S or 4/8-channel TDM input
    • Input sample rates: 44.1 kHz, 48 kHz, 96 kHz
    • Input formats: 16-bit to 32-bit I2S, and TDM
  • Audio Outputs
    • Two-channel bridge-tied load (BTL)
    • Single-channel parallel BTL (PBTL)
    • Up to 2.1 MHz output switching frequency
    • 45 W, 10% THD+N Into 2 Ω at 14.4 V BTL
    • 75 W, 10% THD+N Into 4 Ω at 25 V BTL
    • 150W, 10% THD+N Into 2 Ω at 25V PBTL
  • Audio performance into 4 Ω at 14.4 V BTL
    • THD+N < 0.02% at 1 W
    • 42 µVRMS output noise
    • –90 dB crosstalk
  • Load diagnostics
    • Output open and shorted load
    • Output-to-battery or ground shorts
    • Line output detection up to 6 kΩ
    • Host-independent operation
  • Protection
    • Output current limiting and short protection
    • 40 V Load dump
    • Open ground and power tolerant
    • DC offset
    • Over-temperature
    • Undervoltage and overvoltage
  • General Operation
    • 4.5 V to 18 V supply voltage
    • I2C Control with 4 address options
    • Latched & Non-Latched Clip Detect
    • Enhanced EMI Management

The TAS6422E-Q1 device is a two-channel digital-input Class-D audio amplifier that implements a 2.1 MHz PWM switching frequency enabling a cost-optimized solution in a very small PCB size, full operation down to 4.5 V for start/stop events, and exceptional sound quality with up to 40 kHz audio bandwidth.

The devices adds EMI management features including spread-spectrum to assist in system level EMI challenges.

The output switching frequency can be set either above the AM band, which eliminates AM-band interferences and reduces output filtering and cost, or below the AM band to optimize efficiency.

The device has a built-in load diagnostic function for detecting and diagnosing misconnected outputs as well as detection of AC-coupled tweeters to help to reduce test time during the manufacturing process.

The TAS6422E-Q1 Class-D audio amplifier is designed for use in automotive head units and external amplifier modules. For pin compatible one, two and four-channel devices see the the Device Options table.

The TAS6422E-Q1 device is a two-channel digital-input Class-D audio amplifier that implements a 2.1 MHz PWM switching frequency enabling a cost-optimized solution in a very small PCB size, full operation down to 4.5 V for start/stop events, and exceptional sound quality with up to 40 kHz audio bandwidth.

The devices adds EMI management features including spread-spectrum to assist in system level EMI challenges.

The output switching frequency can be set either above the AM band, which eliminates AM-band interferences and reduces output filtering and cost, or below the AM band to optimize efficiency.

The device has a built-in load diagnostic function for detecting and diagnosing misconnected outputs as well as detection of AC-coupled tweeters to help to reduce test time during the manufacturing process.

The TAS6422E-Q1 Class-D audio amplifier is designed for use in automotive head units and external amplifier modules. For pin compatible one, two and four-channel devices see the the Device Options table.
filter 尋找其它 車用音訊放大器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
具備升級功能，可直接投入使用替代所比較的裝置。
TAS6424E-Q1 現行 汽車、75-W、2-MHz、四通道、4.5 至 26.4-V 數位輸入 D 類音訊放大器 TAS6424E-Q1 is our 4-channel automotive Class-D digital input amplifier which implements 2.1MHz switching frequency.
TAS6421-Q1 現行 具有負載突降的車用 75W、2MHz、單通道 4.5 至 26.4V 數位輸入 D 類音訊放大器 TAS6421-Q1 is our 1-channel automotive Class-D digital input amplifier which implements 2.1-MHz switching frequency.

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 2
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 TAS6422E-Q1 45-W, 2-MHz Digital Input 2-Channel Automotive Class-D Audio Amplifi datasheet (Rev. A) PDF | HTML 2020/11/16
應用說明 Using TI Audio Amplifiers in Automotive Seat Shaker Applications PDF | HTML 2026/1/5

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TAS6422EQ1EVM — 具 I2C 診斷評估模組的 2MHz 2 通道數位輸入 D 類音訊放大器

TAS6422EQ1EVM 評估模組 (EVM) 展示了用於車載資訊娛樂系統的 2 MHz、4 通道數位輸入 D 類音訊解決方案。TAS6422E 的 2.1 MHz 切換頻率可讓使用者能夠大幅減小電感器尺寸，並將整體系統成本最佳化。TAS6422E 為每通道提供 25 W (10% THD+N)，在 14.4 V 電源時為 4 Ω，且其 4.5 V 至 26 V 的廣泛供應電壓能力適用於音響主機和外部放大器系統，同時在啟停低電壓瞬態事件期間提供一流的性能。TAS6422E 採用展頻技術，符合 CISPR25 Class 5 EMI 規範標準，並整合了 I2C 診斷和保護。
使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
應用軟體及架構

PUREPATHCONSOLE — PurePath™ Console graphical development suite for audio system design and development

PurePath™ Console 是一款高度整合且容易使用的音訊開發套件，專爲簡化音訊產品開發相關評估、配置和偵錯程序所設計。瞭解使用 PurePath™ Console 3 軟體有多簡單。

PurePath Console 的直覺式圖形介面無需進階音訊工程專業，因此讓音訊設計更加簡明直觀。在簡單易用的圖形介面中，實作 PurePath Console 的眾多進階控制功能，並以縮短產品開發時間為目標，為您實現高度最佳化的音訊性能、最低功耗和順暢系統整合。

支援的裝置：

PurePath™ Console 1：PCM5142、TAS5721、TAS5729MD、TAS5731 和 (...)
支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HSSOP (DKQ) 56 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片