SN74CB3Q6800
- High-Bandwidth Data Path (Up To 500 MHz
) - 5-V Tolerant I/Os with Device Powered-Up or Powered-Down
- Low and Flat ON-State Resistance (ron) Characteristics Over Operating Range (ron = 4.5
Typical) - Rail-to-Rail Switching on Data I/O Ports
- 0- to 5-V Switching With 3.3-V VCC
- 0- to 3.3-V Switching With 2.5-V VCC
- B-Port Outputs Are Precharged by Bias Voltage (BIASV) to Minimize Signal Distortion During Live Insertion and Hot-Plugging
- Supports PCI Hot Plug
- Bidirectional Data Flow, With Near-Zero Propagation Delay
- Low Input/Output Capacitance Minimizes Loading and Signal Distortion (Cio(OFF) = 3.5 pF Typical)
- Fast Switching Frequency (fON\= 20 MHz Max)
- Data and Control Inputs Provide Undershoot Clamp Diodes
- Low Power Consumption (ICC = 0.75 mA Typical)
- VCC Operating Range From 2.3 V to 3.6 V
- Data I/Os Support 0 to 5-V Signaling Levels (0.8-V, 1.2-V, 1.5-V, 1.8-V, 2.5-V, 3.3-V, 5-V)
- Control Inputs Can be Driven by TTL or 5-V/3.3-V CMOS Outputs
- Ioff Supports Partial-Power-Down Mode Operation
- Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
- ESD Performance Tested Per JESD 22
- 2000-V Human-Body Model (A114-B, Class II)
- 1000-V Charged-Device Model (C101)
- Supports Both Digital and Analog Applications: PCI Interface, Differential Signal Interface, Memory Interleaving, Bus Isolation, Low-Distortion Signal Gating
For additional information regarding the performance
characteristics of the CB3Q family, refer to the TI
application report, CBT-C, CB3T, and CB3Q
Signal-Switch Families, literature number SCDA008.
The SN74CB3Q6800 is a high-bandwidth FET bus switch utilizing a charge pump to elevate the gate voltage of the pass transistor, providing a low and flat ON-state resistance (ron). The low and flat ON-state resistance allows for minimal propagation delay and supports rail-to-rail switching on the data input/output (I/O) ports. The device also features low data I/O capacitance to minimize capacitive loading and signal distortion on the data bus. Specifically designed to support high-bandwidth applications, the SN74CB3Q6800 provides an optimized interface solution ideally suited for broadband communications, networking, and data-intensive computing systems.
The SN74CB3Q6800 is a 10-bit bus switch with a single output-enable (ON\) input. When ON\ is low, the 10-bit
bus switch is ON and the A port is connected to the B port, allowing bidirectional data flow between ports. When
ON\ is high, the 10-bit bus switch is OFF and a high-impedance state exists between the A and B ports. The B
port is precharged to bias voltage (BIASV) through the equivalent of a 10-k resistor when ON\ is high, or if the
device is powered down (VCC = 0 V).
During insertion (or removal) of a card into (or from) an active bus, the card’s output voltage may be close to GND. When the connector pins make contact, the card’s parasitic capacitance tries to force the bus signal to GND, creating a possible glitch on the active bus. This glitching effect can be reduced by using a bus switch with precharged bias voltage (BIASV) of the bus switch equal to the input threshold voltage level of the receivers on the active bus. This method will ensure that any glitch produced by insertion (or removal) of the card will not cross the input threshold region of the receivers on the active bus, minimizing the effects of live-insertion noise.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry prevents damaging current backflow through the device when it is powered down. The device has isolation during power off.
To ensure the high-impedance state during power up or power down, ON\ should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
技術文件
| 重要文件 | 類型 | 標題 | 格式選項 | 下載最新的英文版本 | 日期 | |
|---|---|---|---|---|---|---|
| * | 資料表 | SN74CB3Q6800 datasheet (Rev. A) | 2003/11/20 | |||
| 應用說明 | Selecting the Correct Texas Instruments Signal Switch (Rev. E) | PDF | HTML | 2022/6/2 | |||
| 應用說明 | Multiplexers and Signal Switches Glossary (Rev. B) | PDF | HTML | 2021/12/1 | |||
| Application brief | Eliminate Power Sequencing with Powered-off Protection Signal Switches (Rev. C) | PDF | HTML | 2021/1/6 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
LEADED-ADAPTER1 — 適用於快速測試 TI 的 5、8、10、16 及 24 針腳引線封裝的表面貼裝至 DIP 接頭適配器
EVM-LEADED1 板可用於快速測試和搭建 TI 常見的有引腳封裝 此電路板具備板上配置，可將 TI 的 D、DBQ、DCT、DCU、DDF、DGS、DGV 和 PW 表面黏著封裝轉換為 100mil DIP 排針。
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| SSOP (DBQ) | 24 | Ultra Librarian |
| TSSOP (PW) | 24 | Ultra Librarian |
| TVSOP (DGV) | 24 | Ultra Librarian |