MSPM0G1218
- Core
- Arm 32-bit Cortex M0+ CPU with memory protection unit, frequency up to 80MHz
- PSA-L1 Certification planned
- Operating characteristics
- Extended temperature: –40°C up to 125°C
- Wide supply voltage range: 1.62V to 3.6V
- Memories
- Up to 256KB of flash memory with error correction code (ECC)
- Dual-bank with address swap for OTA updates
- 8KB data flash bank with ECC protection
- 32KB total SRAM with ECC protection or hardware parity
- Up to 256KB of flash memory with error correction code (ECC)
- High-performance analog peripherals
- Up to two simultaneous sampling 12-bit 1.6Msps analog-to-digital converters (ADC) with up to 27 external channels
- 14-bit effective resolution at 100ksps with hardware averaging
- Up to two high-speed comparators (COMP) with integrated 8-bit reference DACs
- 32ns propagation delay in high-speed mode
- Support low-power mode operation down to <1µA
- Programmable analog connections between ADC and COMP
-
Two voltage references (VREF)
-
Configurable 1.4V or 2.5V internal shared voltage reference with external VREF capacitor
-
Configurable 1.4V or 2.5V internal only voltage reference without external VREF capacitor
-
- Integrated temperature sensor
- Up to two simultaneous sampling 12-bit 1.6Msps analog-to-digital converters (ADC) with up to 27 external channels
- Optimized low-power modes (estimates for early samples)
- RUN: 104µA/MHz (CoreMark)
- SLEEP: 614uA at 4MHz
- STOP: 56µA at 32kHz
- STANDBY: 1.4µA at 32kHz with RTC and SRAM state retention
- SHUTDOWN: 69nA with IO wake-up capability
- Intelligent digital peripherals
- 9-channel DMA controller
- Math accelerator supports DIV, SQRT, MAC and TRIG computations
- Five timers support up to 18 PWM channels
- One 16-bit general-purpose timers support QEI
- Two 16-bit general-purpose timers support low-power operation in STANDBY mode
- Two 16-bit advanced timers with deadband support and complimentary outputs up to 12 PWM channels
-
Two basic software timers including 4 independent configurable 16-bit counters each
-
Ability to daisy-chain 2 of the 16-bit counters to form a 32-bit counter
-
Ability to generate 2x interrupt driven PWMs per basic software timer
-
- Two windowed watchdog timers (WWDT), one independent watchdog timer (IWDT)
- RTC with alarm and calendar mode
- Enhanced communication interfaces
-
Five configurable serial interfaces (UNICOMM)
- One configurable serial interface supporting UART or SPI
-
One configurable serial interfaces supporting UART (with LIN) or I2C (controller or target mode)
-
One configurable serial interfaces supporting UART or I2C (controller or target mode)
-
One dedicated UART + LIN interface
-
One dedicated SPI interface up to 32Mbits/s
-
One Controller Area Network (CAN) interface supporting CAN 2.0 A or B and CAN-FD
-
- Clock system
- Internal 4 to 32MHz oscillator (SYSOSC) with up to ±1.2% accuracy
- Phase-locked loop (PLL) up to 80MHz
- Internal 32kHz low-frequency oscillator (LFOSC) with ±3% accuracy
- External 4 to 48MHz crystal oscillator (HFXT)
- External 32kHz crystal oscillator (LFXT)
- External clock input
- Data integrity and encryption
- AES-128/256 accelerator with support for GCM/GMAC, CCM/CBC-MAC, CBC, CTR
- Secure key storage for up to four AES keys
- Flexible firewalls for protecting code and data
- Cyclic redundancy checker (CRC-16, CRC-32)
- Flexible I/O features
- Up to 60 GPIOs
- Two 5V-tolerant open-drain IOs
- Three high-drive IOs with 20mA drive strength
- Four high-speed IOs
- Up to 60 GPIOs
- Development support
- 2-pin serial wire debug (SWD)
- Package options
- 64-pin LQFP (PM) (0.5mm pitch)
- 48-pin LQFP (PT) (0.5mm pitch)
- 48-pin VQFN (RGZ) (0.5mm pitch)
- 32-pin VQFN (RHB) (0.5mm pitch)
-
28-pin WQFN (RUY) (0.4mm pitch)
-
28-pin VSSOP (28DGS) (0.5mm pitch)
-
24-pin VQFN (RGE) (0.4mm pitch)
- Family members (also see Device Comparison)
- MSPM0G1218: 256KB flash, 32KB RAM, 8KB Databank, 2x ADC, 2x COMP
-
MSPM0G1207: 128KB flash, 32KB RAM, 8KB Databank, 1xADC, 1x COMP
-
MSPM0G3218: 256KB flash, 32KB RAM, 8KB Databank, 2x ADC, 2x COMP, 1x CAN-FD
-
MSPM0G3207: 128KB flash, 32KB RAM, 8KB Databank, 1x ADC, 1x COMP, 1x CAN-FD
- Development kits and software (also see Tools and Software)
-
LP-MSPM0G3218 Launchpad Development Kit
- MSPM0 Software Development Kit (SDK)
-
MSPM0Gx218 and MSPM0Gx207 microcontrollers (MCUs) are part of the MSP highly integrated, ultra-low-power 32-bit MCU family based on the enhanced Arm Cortex-M0+ 32-bit core platform, operating at up to 80MHz frequency. These MCUs offer a blend of cost optimization and design flexibility for applications requiring 128KB to 256KB of flash memory in packages ranging from 24 to 64 pins. These devices include CAN-FD controllers, cybersecurity enablers, high performance integrated analog, and provide excellent low power performance across the operating temperature range.
The device has up to 256KB of embedded flash program memory with built-in error correction code (ECC) and up to 32KB SRAM (with ECC and parity protection). The flash memory is organized into two main banks to support field firmware updates, with address swap support provided between the two main banks.
Flexible cybersecurity enablers can be used to support secure boot, secure in-field firmware updates, IP protection (execute-only memory), key storage, and more. Hardware acceleration is provided for a variety of AES symmetric cipher modes. The cybersecurity architecture is pending Arm® PSA Level 1 certification.
A set of high performance analog modules is provided, such as two simultaneously sampling 12-bit, 1.6Msps ADCs supporting up to 27 external channels, on-chip voltage reference (1.4V or 2.5V), and two comparators operable in low-power and high-speed modes with additional built-in 8-bit reference DACs.
The TI MSPM0 family of low-power MCUs consists of devices with varying degrees of analog and digital integration. The MSPM0 MCU platform combines the Arm Cortex-M0+ platform with a holistic ultra-low-power system architecture, allowing system designers to increase performance while reducing energy consumption.
MSPM0Gx218 and MSPM0Gx207 MCUs are supported by an extensive hardware and software ecosystem with reference designs and code examples to get the design started quickly. Development kits include a LaunchPad available for purchase. TI also provides a free MSPM0 Software Development Kit (SDK), which is available as a component of Code Composer Studio™ IDE desktop and cloud version within the TI Resource Explorer. MSPM0 MCUs are also supported by extensive online collateral, training with MSP Academy, and online support through the TI E2E™ support forums.
For complete module descriptions, see the MSPM0 G-Series 80MHz Microcontrollers Technical Reference Manual.
技術文件
| 重要文件 | 類型 | 標題 | 格式選項 | 日期 |
|---|---|---|---|---|
| * | Data sheet | Mixed-Signal Microcontrollers With CAN-FD Interface datasheet | PDF | HTML | 2026年 2月 24日 |
| * | Errata | MSPM0G321x/MSPM0G320x Mixed-Signal Microcontrollers Errata | PDF | HTML | 2026年 2月 13日 |
| * | User guide | MSPM0 G-Series 80-MHz Microcontrollers Technical Reference Manual (Rev. D) | 2026年 3月 20日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
LP-MSPM0G3218 — MSPM0G3218 LaunchPad™ development kit evaluation module
MSPM0-ANALOG-CONFIGURATOR — Analog Configurator for MSPM0
The MSPM0 analog configurator is a graphical configuration tool designed to simplify and accelerate the design and enablement of an analog signal chain using a MSPM0 device with no traditional coding development necessary.
The tool uses an intuitive GUI to configure a signal chain using the high (...)
支援產品和硬體
CCSTUDIO-STARTHUB — Example application browser
支援產品和硬體
MSP-MOTOR-CONTROL — MSP firmware solutions for motor control
MSP Motor Control is a collection of software, tools and examples to spin motors in 30 minutes or less with MSPM0 Arm® Cortex® M0+ MCUs and popular motor driver solutions.
MSP Motor Control provides examples for supported hardware kits to spin brushed, stepper, and three-phase motors with sensored (...)
支援產品和硬體
TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud
支援產品和硬體
CCSTUDIO — Code Composer Studio™ integrated development environment (IDE)
CCStudio™ IDE is part of TI's extensive CCStudio™ development tool ecosystem. It is an integrated development environment (IDE) for TI's microcontrollers, processors, wireless connectivity devices and radar sensors. It is comprised of a rich suite of tools used to build, debug, analyze and optimize (...)
支援產品和硬體
MSP-ZERO-CODE-STUDIO — Graphical development environment for designing applications for MSP microcontrollers
MSP Zero Code Studio is a visual design environment that simplifies firmware development, making it possible to configure, develop, and run microcontroller applications in minutes with zero coding and no IDE required. Available as a standalone download or on the cloud.
支援產品和硬體
SYSCONFIG — Standalone desktop version of SysConfig
SysConfig is a configuration tool designed to simplify hardware and software configuration challenges to accelerate software development.
SysConfig is available as part of the Code Composer Studio™ integrated development environment as well as a standalone application. Additionally SysConfig (...)
支援產品和硬體
MSPM0-ACADEMY — MSPM0 Academy
支援產品和硬體
MSP-GANG-SOFTWARE — MSP-GANG Software
支援產品和硬體
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash is a software tool for programming on-chip flash on TI microcontrollers and wireless connectivity devices and on-board flash for TI processors. UniFlash provides both graphical and command-line interfaces.
UniFlash can be run from the cloud on the TI Developer Zone or downloaded and used (...)
支援產品和硬體
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| VQFN (RGZ) | 48 | Ultra Librarian |
| VQFN (RHB) | 32 | Ultra Librarian |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中的可靠性監測
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。