首頁 電源管理 多通道 IC (PMIC)
首頁
電源管理
多通道 IC (PMIC)

LP875761-Q1

現行

具整合式開關的四相 3-Mhz 1-V 16-A DC/DC 降壓轉換器

立即訂購
產品規格表

LP875761-Q1

現行
產品規格表 立即訂購

產品詳細資料

Processor supplier Mobileye Processor name EyeQ4 High Product type Processor and FPGA Regulated outputs (#) 1 Step-down DC/DC converter 1 Step-up DC/DC converter 0 LDO 0 Vin (min) (V) 2.8 Vin (max) (V) 5.5 Vout (min) (V) 0.985 Vout (max) (V) 1.015 Iout (max) (A) 16 Configurability Factory programmable, Hardware configurable Features Dynamic voltage scaling, Enable, Enable pin, I2C control, Overcurrent protection, Power good, Power sequencing, Power supply and system monitoring, Spread-Spectrum Clock (SSC) Generation, Thermal shutdown, UVLO fixed Rating Automotive Operating temperature range (°C) -40 to 125 Step-down DC/DC controller 0 Step-up DC/DC controller 0 Iq (typ) (mA) 0.0067 Switching frequency (max) (kHz) 3300 Shutdown current (ISD) (typ) (µA) 1.4 Switching frequency (typ) (kHz) 3000 Step-down DC/DC Iout (typ) (A) 16
Processor supplier Mobileye Processor name EyeQ4 High Product type Processor and FPGA Regulated outputs (#) 1 Step-down DC/DC converter 1 Step-up DC/DC converter 0 LDO 0 Vin (min) (V) 2.8 Vin (max) (V) 5.5 Vout (min) (V) 0.985 Vout (max) (V) 1.015 Iout (max) (A) 16 Configurability Factory programmable, Hardware configurable Features Dynamic voltage scaling, Enable, Enable pin, I2C control, Overcurrent protection, Power good, Power sequencing, Power supply and system monitoring, Spread-Spectrum Clock (SSC) Generation, Thermal shutdown, UVLO fixed Rating Automotive Operating temperature range (°C) -40 to 125 Step-down DC/DC controller 0 Step-up DC/DC controller 0 Iq (typ) (mA) 0.0067 Switching frequency (max) (kHz) 3300 Shutdown current (ISD) (typ) (µA) 1.4 Switching frequency (typ) (kHz) 3000 Step-down DC/DC Iout (typ) (A) 16
VQFN-HR (RNF) 26 18 mm² (4.5 mm × 4 mm)
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
    • Device HBM ESD Classification Level 2
    • Device CDM ESD Classification Level C4B
  • Input Voltage: 2.8 V to 5.5 V
  • Output Voltage: 1.0 V
  • Four High-Efficiency Step-Down DC/DC Converter Cores:
    • Maximum Output Current: 16 A (4 A per Phase)
  • Switching Frequency: 3 MHz
  • Spread-Spectrum Mode and Phase Interleaving
  • Configurable General Purpose I/O (GPIOs)
  • I2C-Compatible Interface That Supports Standard (100 kHz), Fast (400 kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
  • Interrupt Function With Programmable Masking
  • Programmable Power-Good Signal (PGOOD)
  • Output Short-Circuit and Overload Protection
  • Overtemperature Warning and Protection
  • Overvoltage Protection (OVP) and Undervoltage Lockout (UVLO)
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
    • Device HBM ESD Classification Level 2
    • Device CDM ESD Classification Level C4B
  • Input Voltage: 2.8 V to 5.5 V
  • Output Voltage: 1.0 V
  • Four High-Efficiency Step-Down DC/DC Converter Cores:
    • Maximum Output Current: 16 A (4 A per Phase)
  • Switching Frequency: 3 MHz
  • Spread-Spectrum Mode and Phase Interleaving
  • Configurable General Purpose I/O (GPIOs)
  • I2C-Compatible Interface That Supports Standard (100 kHz), Fast (400 kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
  • Interrupt Function With Programmable Masking
  • Programmable Power-Good Signal (PGOOD)
  • Output Short-Circuit and Overload Protection
  • Overtemperature Warning and Protection
  • Overvoltage Protection (OVP) and Undervoltage Lockout (UVLO)

The LP875761-Q1 device is designed to meet the power-management requirements of the latest processors and platforms in various automotive power applications. The device contains four step-down DC/DC converter cores, which are configured as a 4-phase output in forced-PWM mode. The device is controlled by an I2C-compatible serial interface and by enable signals.

The LP875761-Q1 supports remote differential-voltage sensing for multiphase outputs to compensate IR drop between the regulator output and the point-of-load (POL) which improves the accuracy of the output voltage. The switching clock can be forced to PWM mode and also synchronized to an external clock to minimize the disturbances.

The LP875761-Q1 device supports load-current measurement without the addition of external current-sense resistors. The LP875761-Q1 device also supports programmable start-up and shutdown delays and sequences synchronized to enable signals. The sequences can also include GPIO signals to control external regulators, load switches, and processor reset. During start-up, the device controls the output slew rate to minimize output-voltage overshoot and in-rush current.

The LP875761-Q1 device is designed to meet the power-management requirements of the latest processors and platforms in various automotive power applications. The device contains four step-down DC/DC converter cores, which are configured as a 4-phase output in forced-PWM mode. The device is controlled by an I2C-compatible serial interface and by enable signals.

The LP875761-Q1 supports remote differential-voltage sensing for multiphase outputs to compensate IR drop between the regulator output and the point-of-load (POL) which improves the accuracy of the output voltage. The switching clock can be forced to PWM mode and also synchronized to an external clock to minimize the disturbances.

The LP875761-Q1 device supports load-current measurement without the addition of external current-sense resistors. The LP875761-Q1 device also supports programmable start-up and shutdown delays and sequences synchronized to enable signals. The sequences can also include GPIO signals to control external regulators, load switches, and processor reset. During start-up, the device controls the output slew rate to minimize output-voltage overshoot and in-rush current.
filter 尋找其它 多通道 IC (PMIC)
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
針腳對針腳的功能與所比較的裝置相同。
LP875701-Q1 現行 適用於 Mobileye EyeQ4 的車用多相 1V、10A 降壓轉換器 This product has a lower output current (10 A).

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 4
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 LP875761-Q1 Four-Phase 3-MHz 1-V 16-A DC/DC Buck Converter With Integrated Switches datasheet PDF | HTML 2020/12/9
使用指南 LP875761A-Q1 Technical Reference Manual PDF | HTML 2020/9/21
證書 LP875761Q1EVM EU Declaration of Conformity (DoC) 2020/8/13
應用說明 Power supply design for mobileye eyeQ4 high using LP875761-Q1 PDF | HTML 2019/2/22

設計與開發

電源供應解決方案

探索包括 LP875761-Q1 的解決方案。TI 提供適用於 TI 與非 TI 之系統單晶片 (SoC)、處理器、微控制器、感測器或現場可編程邏輯閘陣列 (FPGA) 的電源供應解決方案。

檢視解決方案
模擬型號

LP875761-Q1 PSPICE Model

SNVMC22.ZIP (280 KB) - PSpice 模型
支援產品和硬體
模擬型號

LP875761-Q1 SIMPLIS Model

SNVMC14.ZIP (28 KB) - SIMPLIS 模型
支援產品和硬體
計算工具

PEET-GUI — PMIC 效率評估器工具 (PEET)

The PMIC Efficiency Estimator Tool (PEET GUI) is a graphical user interface used to easily evaluate PMIC DC/DC regulator efficiency relative to your design conditions. The PEET GUI can be used to configure each DC/DC regulator separately and provides real-time efficiency and power dissipation data (...)
支援產品和硬體
參考設計

TIPA-050040 — 使用 LP875761-Q1 的 Mobileye EyeQ4 高電源供應設計

此電源供應器設計詳細說明使用 LP875761-Q1 電源管理 IC 的 Mobileye EyeQ4® 高 SoC (系統單晶片) 核心軌的電源考量。此電源解決方案假設輸入電壓為 3.3V 或 5V (±5%)。若系統輸入電壓較高，例如汽車電池，應使用降壓轉換器作為前置穩壓器，以產生 3.3V 或 5V 的供應電壓。

 

LP875761-Q1 具有 4 個降壓轉換器，可作為單一 1V 輸出多相轉換器。輸出啟動時，LP875761 會以 PWM 模式運作，且 4 個相位全以交錯模式切換。

 

如需詳細資訊，請見使用指南。

支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VQFN-HR (RNF) 26 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片