首頁 電源管理 多通道 IC (PMIC)
首頁
電源管理
多通道 IC (PMIC)

LP87524-Q1

現行

具整合式開關的車用 10A、1 相位、四輸出降壓轉換器

立即訂購
產品規格表
使用指南

LP87524-Q1

現行
立即訂購

產品詳細資料

Processor supplier Generic Processor name Generic Product type Radar sensor Regulated outputs (#) 4 Step-down DC/DC converter 4 Step-up DC/DC converter 0 LDO 0 Vin (min) (V) 2.8 Vin (max) (V) 5.5 Vout (min) (V) 0.6 Vout (max) (V) 3.36 Iout (max) (A) 4 Configurability Factory programmable, Software configurable Features Diagnostics, Dynamic voltage scaling, Enable, Enable pin, I2C control, Overcurrent protection, Power good, Power sequencing, Power supply and system monitoring, Spread-Spectrum Clock (SSC) Generation, Thermal shutdown, UVLO fixed Rating Automotive Operating temperature range (°C) -40 to 125 Step-down DC/DC controller 0 Step-up DC/DC controller 0 Iq (typ) (mA) 0.0067 Switching frequency (max) (kHz) 2200 Shutdown current (ISD) (typ) (µA) 1.4 Switching frequency (typ) (kHz) 2000
Processor supplier Generic Processor name Generic Product type Radar sensor Regulated outputs (#) 4 Step-down DC/DC converter 4 Step-up DC/DC converter 0 LDO 0 Vin (min) (V) 2.8 Vin (max) (V) 5.5 Vout (min) (V) 0.6 Vout (max) (V) 3.36 Iout (max) (A) 4 Configurability Factory programmable, Software configurable Features Diagnostics, Dynamic voltage scaling, Enable, Enable pin, I2C control, Overcurrent protection, Power good, Power sequencing, Power supply and system monitoring, Spread-Spectrum Clock (SSC) Generation, Thermal shutdown, UVLO fixed Rating Automotive Operating temperature range (°C) -40 to 125 Step-down DC/DC controller 0 Step-up DC/DC controller 0 Iq (typ) (mA) 0.0067 Switching frequency (max) (kHz) 2200 Shutdown current (ISD) (typ) (µA) 1.4 Switching frequency (typ) (kHz) 2000
VQFN-HR (RNF) 26 18 mm² (4.5 mm × 4 mm)
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
    • Device HBM ESD Classification Level 2
    • Device CDM ESD Classification Level C4B
  • Input Voltage: 2.8 V to 5.5 V
  • Output Voltage: 0.6 V to 3.36 V
  • Four High-Efficiency Step-Down DC/DC Converter Cores:
    • Maximum Output Current: 10 A
  • Switching Frequency: 2 MHz
  • Spread-Spectrum Mode and Phase Interleaving
  • Configurable General Purpose I/O (GPIOs)
  • I2C-Compatible Interface That Supports Standard (100 kHz), Fast (400 kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
  • Interrupt Function With Programmable Masking
  • Programmable Power-Good Signal (PGOOD)
  • Output Short-Circuit and Overload Protection
  • Overtemperature Warning and Protection
  • Overvoltage Protection (OVP) and Undervoltage Lockout (UVLO)
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
    • Device HBM ESD Classification Level 2
    • Device CDM ESD Classification Level C4B
  • Input Voltage: 2.8 V to 5.5 V
  • Output Voltage: 0.6 V to 3.36 V
  • Four High-Efficiency Step-Down DC/DC Converter Cores:
    • Maximum Output Current: 10 A
  • Switching Frequency: 2 MHz
  • Spread-Spectrum Mode and Phase Interleaving
  • Configurable General Purpose I/O (GPIOs)
  • I2C-Compatible Interface That Supports Standard (100 kHz), Fast (400 kHz), Fast+ (1 MHz), and High-Speed (3.4 MHz) Modes
  • Interrupt Function With Programmable Masking
  • Programmable Power-Good Signal (PGOOD)
  • Output Short-Circuit and Overload Protection
  • Overtemperature Warning and Protection
  • Overvoltage Protection (OVP) and Undervoltage Lockout (UVLO)

The LP8752x-Q1 device is designed to meet the power-management requirements of the latest processors and platforms in various automotive power applications. The device contains four step-down DC/DC converter cores, which are configured as a 4-phase output, 3-phase and 1-phase outputs, 2-phase and 2-phase outputs, one 2-phase and two 1-phase outputs, or four 1-phase outputs. The device is controlled by an I2C-compatible serial interface and by enable signals.

The automatic pulse-width-modulation (PWM) to pulsed-frequency-modulation (PFM) operation (AUTO mode), together with the automatic phase adding and phase shedding, maximizes efficiency over a wide output-current range. The LP8752x-Q1 supports remote differential-voltage sensing for multiphase outputs to compensate IR drop between the regulator output and the point-of-load (POL) improving the accuracy of the output voltage. The switching clock can be forced to PWM mode and also synchronized to an external clock to minimize the disturbances.

The LP8752x-Q1 device supports load-current measurement without the addition of external current-sense resistors. The device also supports programmable start-up and shutdown delays and sequences synchronized to enable signals. The sequences can include GPIO signals to control external regulators, load switches, and processor reset. During start-up and voltage change, the device controls the output slew rate to minimize output-voltage overshoot and in-rush current.

The LP8752x-Q1 device is designed to meet the power-management requirements of the latest processors and platforms in various automotive power applications. The device contains four step-down DC/DC converter cores, which are configured as a 4-phase output, 3-phase and 1-phase outputs, 2-phase and 2-phase outputs, one 2-phase and two 1-phase outputs, or four 1-phase outputs. The device is controlled by an I2C-compatible serial interface and by enable signals.

The automatic pulse-width-modulation (PWM) to pulsed-frequency-modulation (PFM) operation (AUTO mode), together with the automatic phase adding and phase shedding, maximizes efficiency over a wide output-current range. The LP8752x-Q1 supports remote differential-voltage sensing for multiphase outputs to compensate IR drop between the regulator output and the point-of-load (POL) improving the accuracy of the output voltage. The switching clock can be forced to PWM mode and also synchronized to an external clock to minimize the disturbances.

The LP8752x-Q1 device supports load-current measurement without the addition of external current-sense resistors. The device also supports programmable start-up and shutdown delays and sequences synchronized to enable signals. The sequences can include GPIO signals to control external regulators, load switches, and processor reset. During start-up and voltage change, the device controls the output slew rate to minimize output-voltage overshoot and in-rush current.
filter 尋找其它 多通道 IC (PMIC)
下載 觀看有字幕稿的影片 影片
索取更多資訊

提供功能安全資訊，例如失效模式、影響和診斷分析 (FMEDA)、安全分析報告和安全手冊。立即索取

您可能會感興趣的類似產品

open-in-new 比較替代產品
針腳對針腳的功能與所比較的裝置相同。
LP87523-Q1 現行 具有整合式開關的車用 10A、2 相位 + 1 相位 + 1 相位、3 輸出降壓轉換器 Three output phase configuration of LP8752x-Q1 family.
LP87564-Q1 現行 具有整合式開關的車用多相四路 4A 降壓轉換器 This product has a higher maximum output current.

技術文件

找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 11
重要文件 類型 標題 格式選項 下載最新的英文版本 日期
* 資料表 LP8752x-Q1 10-A Buck Converter With Integrated Switches datasheet PDF | HTML 2018/3/15
* 使用指南 LP875241S-Q1 Technical Reference Manual PDF | HTML 2024/6/25
* 使用指南 LP875241U-Q1 Technical Reference Manual PDF | HTML 2024/6/25
* 使用指南 LP875241J-Q1 Technical Reference Manual PDF | HTML 2021/9/2
* 使用指南 LP87524x-Q1 Technical Reference Manual (Rev. A) PDF | HTML 2021/5/10
* 使用指南 LP87524T-Q1 Technical Reference Manual (Rev. A) PDF | HTML 2019/10/30
使用指南 LP8752x-Q1 Configuration Guide (Rev. A) PDF | HTML 2025/7/30
應用說明 Power Supply Design for Semidrive X9P/X9U PDF | HTML 2022/5/19
Application brief The Benefits of FlexPower PMIC Devices (Rev. B) PDF | HTML 2020/11/23
應用說明 How to Design Flexible Processor Power Systems Using PMICs (Rev. B) 2020/1/27
應用說明 Stability Considerations for LP8756x-Q1 and LP8752x-Q1 PDF | HTML 2019/6/4

設計與開發

電源供應解決方案

探索包括 LP87524-Q1 的解決方案。TI 提供適用於 TI 與非 TI 之系統單晶片 (SoC)、處理器、微控制器、感測器或現場可編程邏輯閘陣列 (FPGA) 的電源供應解決方案。

檢視解決方案
開發板

LP87524Q1EVM — LP87524-Q1 四路輸出單相降壓轉換器評估模組

LP87524Q1EVM 展示了德州儀器的積體電路 LP87524-Q1。LP87524-Q1 為一高性能，多相降壓式轉換器，設計用途可滿足汽車應用中最新應用處理器的電源管理需求。本裝置包含四個降壓式 DC-DC 轉換器核心，並配置為四個獨立單相降壓轉換器。LP87524-Q1 能夠驅動高達 10A 總負載電流，並完美結合解決方案尺寸與效率。此裝置可透過 PC 及隨附的 GUI 控制。
使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
開發板

LP87564Q1EVM — 具有整合式開關的四輸出、單相 4-A 降壓轉換器評估模組

LP87564Q1EVM 展示了德州儀器的積體電路 LP87564-Q1。

LP87564-Q1 為一高性能，多相降壓式轉換器，設計用途可滿足汽車應用中最新應用處理器的電源管理需求。本裝置包含四個降壓式 DC-DC 轉換器核心，並配置為四個單相降壓轉換器。LP87564-Q1 可驅動高達 4A + 4A + 4A +4A 的負載電流，並完美結合解決方案尺寸與效率。此裝置可透過 PC 及隨附的 GUI 控制。

此 EVM 可編程，以匹配 LP87564 或 LP87524 系列的任何配置。

使用指南: PDF
支援產品和硬體
有庫存
限制：
??asset.out-of-stock-ti_zh_TW??
無法提供
模擬型號

LP87524-Q1 PSpice Transient Model (Rev. A)

SNVMB02A.ZIP (360 KB) - PSpice 模型
支援產品和硬體
模擬型號

LP8756-Q1 and LP8752-Q1 SIMPLIS Model

SNVMBU8.ZIP (42 KB) - SIMPLIS 模型
支援產品和硬體
模擬型號

LP875x-Q1 SIMPLIS Model

SNVMBT5.ZIP (42 KB) - SIMPLIS 模型
支援產品和硬體
計算工具

PEET-GUI — PMIC 效率評估器工具 (PEET)

The PMIC Efficiency Estimator Tool (PEET GUI) is a graphical user interface used to easily evaluate PMIC DC/DC regulator efficiency relative to your design conditions. The PEET GUI can be used to configure each DC/DC regulator separately and provides real-time efficiency and power dissipation data (...)
支援產品和硬體
參考設計

TIPA-050044 — 適用於汽車應用的 X9P/U 電源供應設計

此專為 SemiDrive X9U 和 X9U 汽車 SoC 打造的電源供應設計，最適合汽車資訊娛樂及電子駕駛艙應用。本文件概述使用 FlexPower PMIC 的電源設計考量。

支援產品和硬體
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VQFN-HR (RNF) 26 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片