TPS659128
- Four step-down converters:
- Input voltage (VIN) range from 2.7 V to 5.5 V
- Power save mode at light load current
- Output voltage accuracy in PWM mode ±2%
- Typical 26-µA quiescent current per converter
- Dynamic voltage scaling
- 100% duty cycle for lowest dropout
- Ten LDOs:
- 8 general-purpose LDOs
- Output voltage range from 0.8 V to 3.3 V
- Typical 32-µA quiescent current per LDO
- 2 low-noise RF-LDOs
- Output voltage range from 1.6 V to 3.3 V
- Preregulation support by separate power inputs
- Eco-mode™ control scheme
- VIN range of LDOs respective to the
following voltage ranges:
- 1.8 V to 3.6 V
- 3 V to 5.5 V
- Three LED drivers:
- Internal dimming using I2C
- Up to 20 mA per current sink
- Thermal monitoring
- High temperature warning
- Thermal shutdown
- Bypass switch
- Used with DCDC4 in applications powering a Radio Frequency Power Amplifier (RF-PA)
- Interface
- I2C interface
- Power I2C interface for Dynamic Voltage Scaling (DVS)
- Serial Peripheral Interface (SPI)
- 32-kHz RC oscillator
- Undervoltage lockout, battery fault comparator, and long button-press detection
- 3.6-mm × 3.6-mm DSBGA package with 0.4-mm pitch
The TPS659128x device provides four configurable step-down converters with up to 2.5-A output current and ten LDO regulators for external use. These LDOs can be supplied from either a battery or a preregulated supply. Each specific part number has a different factory programmed power-up and power-down sequence.
The TPS659128x device integrates a 32-kHz RC oscillator to sequence all resources during power up or power down. All LDOs and DC-DC converters can be controlled by an I2C or SPI interface or basic enable pins after boot. Additionally, a voltage-scaling interface allows for transitioning the DC-DC converters to a different voltage through I2C or basic roof-floor control. Three LED drivers with an advanced dimming feature are integrated inside the device. General-purpose input-output (GPIO) functionality is multiplexed with various pins, including LED pins, ENx pins, and SPI pins when not used. Each GPIO can be configured as part of the power-up sequence to control external resources. One SLEEP pin enables switching between the active mode and preprogrammed sleep mode for power optimization. The TPS659128x device comes in a 9-pin × 9-pin DSBGA package (3.6 mm × 3.6 mm) with a 0.4-mm pitch.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | TPS659128 PMU for Processor Power datasheet (Rev. A) | 2021. 6. 10 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPS65912SW-LINUX — TPS65912용 Linux 드라이버
The Linux driver supports the TPS65912 Video ADC. The Linux driver supports communication through the I2C and SPI bus and interfaces with the Regulator sub-system.
Linux Mainline Status
Available in Linux Main line: Yes
Available through git.ti.com: N/A
Supported Devices:
- tps65912
Linux Source Files
The (...)
IPG-UI — IPG-UI EVM GUI (Windows Installer)
IPG-UI GUI를 사용하여 여러 PMIC 디바이스를 구성하여 이러한 디바이스의 기능과 성능을 평가할 수 있습니다. 이 GUI는 웹 기반 기술을 사용하여 제작되었으며 USB2ANY 어댑터 보드를 사용하여 EVM 하드웨어와의 상호 작용을 지원합니다. USB2ANY 탐색기는 USB2ANY 어댑터 보드의 펌웨어를 필요한 버전(2.7.0.0 이상)으로 업데이트할 수 있도록 제공됩니다.
IPG-UI-LINUX — IPG-UI EVM GUI (Linux Installer)
IPG-UI GUI를 사용하여 여러 PMIC 디바이스를 구성하여 이러한 디바이스의 기능과 성능을 평가할 수 있습니다. 이 GUI는 웹 기반 기술을 사용하여 제작되었으며 USB2ANY 어댑터 보드를 사용하여 EVM 하드웨어와의 상호 작용을 지원합니다. USB2ANY 탐색기는 USB2ANY 어댑터 보드의 펌웨어를 필요한 버전(2.7.0.0 이상)으로 업데이트할 수 있도록 제공됩니다.
IPG-UI-OSX — IPG-UI EVM GUI (OSX Installer)
IPG-UI GUI를 사용하여 여러 PMIC 디바이스를 구성하여 이러한 디바이스의 기능과 성능을 평가할 수 있습니다. 이 GUI는 웹 기반 기술을 사용하여 제작되었으며 USB2ANY 어댑터 보드를 사용하여 EVM 하드웨어와의 상호 작용을 지원합니다. USB2ANY 탐색기는 USB2ANY 어댑터 보드의 펌웨어를 필요한 버전(2.7.0.0 이상)으로 업데이트할 수 있도록 제공됩니다.
SLVC435 — TPS65912xEVM Software – Legacy
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| DSBGA (YFF) | 81 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.