TPS65381A-Q1
- Qualified for Automotive Applications
- AEC-Q100 Qualified With the
Following Results:
- Device Temperature Grade 1: –40°C to +125°C Ambient Operating Temperature
- Device HBM ESD Classification Level H2
- Device CDM ESD Classification Level C3B
- Multirail Power
Supply Supporting Among Others
- TI Hercules™ TMS570, C2000™, and Various Functional-Safety Architecture Microcontrollers
- Supply Rails
- Input voltage range:
- 5.8 V to 36 V (CAN, I/O, MCU Core, and Sensor-Supply Regulators Functional)
- 4.5 V to 5.8 V (3.3 V I/O and MCU Core Regulators Functional)
- 6-V Asynchronous Switch Mode Preregulator With Internal FET, 1.3-A Output Current
- 5-V (CAN) Supply Voltage, Linear Regulator With Internal FET, 300-mA Output Current
- 3.3-V or 5-V (MCU I/O) Voltage, Linear Regulator With Internal FET, 300-mA Output Current
- 0.8-V to 3.3-V Adjustable (MCU Core Voltage), Linear Regulator Controller With External FET
- 3.3-V to 9.5-V Adjustable Sensor Supply: Linear Tracking Regulator With Internal FET, 100-mA Output Current, and Protection Against Short-to-Supply and Short-to-Ground
- Charge Pump: Typically 12 V Above Battery Voltage
- Input voltage range:
- Power Supply and System Monitoring
- Independent Undervoltage and Overvoltage Monitoring on All Regulator Outputs, Battery Voltage, and Internal Supplies
- Independent Voltage References for Regulator References and Voltage Monitoring. Voltage-Monitoring Circuitry With Independent Bandgap Reference and Separate Supply Input Pin
- Self-Check on all Voltage Monitoring (Automatic During Power-Up and After Power-Up Initiated by External MCU)
- All Supplies With Internal FETs Protected With Current-Limit and Overtemperature Shutdown
- Microcontroller (MCU) Interface
- Watchdog: Trigger Mode (OPEN/CLOSE Window) or Question and Answer Mode
- MCU Error-Signal Monitor For Lock-Step Dual-Core MCUs Including Hercules™ TMS570, C2000™, and Various Functional-Safety Architecture MCUs Using Pulse-Width Modulation (PWM) Error Output
- DIAGNOSTIC State for Performing Device Self-Tests, Diagnostics, and External Interconnect Checks
- SAFE State for Device and System Protection on Error Event Detection
- Clock Monitor for Internal Oscillator
- Self-Tests for Analog- and Digital-Critical Circuits Executed With Every Device Power Up or Activated by MCU in DIAGNOSTIC State
- CRC on Nonvolatile Memory, Device and Configuration Registers
- Reset Circuit and Output Pin for MCU
- Diagnostic Output Pin Allowing MCU to Observe Through a Multiplexer Internal Analog and Digital Signals of the Device
- Serial
Peripheral Interface (SPI)
- Configuration Registers
- Watchdog Question and Answers
- Diagnostic Status Readout
- Compliant With 3.3-V and 5-V Logic Levels
- Enable Drive Output for Disabling Safing-Path or External Power-Stages on Detected System-Failure
- Wakeup Through IGNITION Pin or CAN WAKEUP Pin
- Package: 32-Pin HTSSOP PowerPAD™ IC Package
The TPS65381A-Q1 device is a multirail power supply designed to supply microcontrollers (MCUs) in safety-relevant applications, such as those found in automotive and industrial markets. The device supports Texas Instruments’ Hercules™ TMS570 MCU and C2000™ MCU families, and various other MCUs with dual-core lockstep (LS) or loosely-coupled architectures (LC).
The TPS65381A-Q1 device integrates multiple supply rails to power the MCU, controller area network (CAN), or FlexRay, and an external sensor. An asynchronous-buck switch-mode power-supply converter with an internal FET converts the input supply (battery) voltage to a 6-V preregulator output. This 6-V preregulator supplies the other regulators. The device supports wakeup from IGNITION or wakeup from the CAN transceiver.
The integrated, fixed 5-V linear regulator with internal FET can be used for a CAN or FlexRay transceiver supply for example. A second linear regulator, also with an internal FET, regulates to a selectable 5-V or 3.3-V output which, for example, can be use for the MCU I/O voltage.
The TPS65381A-Q1 device includes an adjustable linear-regulator controller, requiring an external FET and resistor divider, that regulates to an adjustable voltage of between 0.8 V and 3.3 V which may be used for the MCU core supply.
The integrated sensor supply can be run in tracking mode or adjustable output mode and includes short-to-ground and short-to-battery protection. Therefore, this regulator can power a sensor outside the module or electronic control unit (ECU).
The integrated charge pump provides overdrive voltage for the internal regulators. The charge pump can also be used in a reverse-battery protection circuit by using the charge-pump output to control an external NMOS transistor. This solution allows for a lower minimum-battery-voltage operation compared to a traditional reverse-battery blocking diode when the device must be operational at the lowest possible supply voltages.
The device monitors undervoltage and overvoltage on all regulator outputs, battery voltage, and internal supply rails. A second bandgap reference, independent from the main bandgap reference, is used for the undervoltage and overvoltage monitoring, to avoid any drifts in the main bandgap reference from being undetected. In addition, regulator current-limits and temperature protections are implemented.
The TPS65381A-Q1 device has monitoring and protection functions, which include the following: watchdog with trigger and question and answer modes, MCU error-signal monitor, clock monitoring on internal oscillators, self-check on the clock monitor, cyclic redundancy check (CRC) on nonvolatile memory, a diagnostic output pin allowing the MCU to observe internal analog and digital signals of the device, a reset circuit and output pin for the MCU, and an enable drive output to disable the safing-path or external-power stages on detected faults. A built-in self-test (BIST) monitors the device functionality automatically at power-up. A dedicated DIAGNOSTIC state allows the MCU to check TPS65381A-Q1 monitoring and protection functions.
The TPS65381A-Q1 device is offered in a 32-pin HTSSOP PowerPAD package.
추가 정보
기능 안전성 문서를 사용할 수 있습니다. 지금 요청
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | TPS65381A-Q1 Multirail Power Supply for Microcontrollers in Safety-Relevant Applications datasheet (Rev. A) | PDF | HTML | 2017. 5. 1 | |
| 기능 안전 정보 | Safety Manual for TPS65381-Q1 and TPS65381A-Q1 Multirail Power Supply (Rev. D) | PDF | HTML | 2021. 3. 2 | ||
| 애플리케이션 노트 | TPS65381-Q1 and TPS65381A-Q1 Design Checklist (Rev. A) | 2017. 4. 5 | |||
| 애플리케이션 노트 | Device Behavior Under Slow VBAT Ramp-Down and Ramp-Up | 2015. 1. 23 | |||
| 애플리케이션 노트 | Efficiency Evaluation TPS65381-Q1 | 2013. 8. 29 | |||
| 애플리케이션 노트 | DPI Evaluation TPS65381-Q1 | 2013. 2. 28 |
설계 및 개발
전원 공급 솔루션
TPS65381A-Q1을 포함하는 솔루션을 살펴보세요. TI는 칩(SoC), 프로세서, 마이크로컨트롤러, 센서 또는 FPGA(Field Programmable Gate Array)의 TI와 비TI 시스템을 위한 전원 공급 솔루션을 제공합니다.
TPS65381-Q1 Unencrypted PSpice Transient Model Package (Rev. A)
TPS65381-Q1 VDD3-5 TINA-TI Transient Reference Design
TPS65381-Q1 VSOUT1 TINA-TI Transient Reference Design
TIPA-050010 — TPS65381x-Q1 PMIC를 사용하는 TMS570 전원 공급 장치 설계
이 전원 공급 장치 설계는 TMS570에 전원을 공급하는 데 최적화된 전원 관리 IC를 설명하고, 개발자가 TPS65381x-Q1 PMIC를 안전 관련 시스템에 통합하는 데 도움이 되는 정보를 자세히 설명합니다.
TPS65381x-Q1 장치는 차량용 및 산업용 시장에서 볼 수 있는 것과 같은 안전 관련 애플리케이션에서 마이크로컨트롤러(MCU)를 제공하도록 설계된 다중 레일 전원 공급 장치입니다. 이 장치는 TMS570 MCU와 C2000 마이크로컨트롤러 제품군과 듀얼 코어 락스탭(LS)이나 느슨하게 결합된 아키텍처(LC)를 (...)
TIPA-050011 — TPS65381x-Q1 PMIC를 사용하는 C2000™ 마이크로컨트롤러 전원 공급 장치 설계
이 전원 공급 장치 설계는 C2000™ 마이크로컨트롤러에 전원을 공급하는 최적화된 전원 관리 IC를 설명하고, 개발자가 TPS65381x-Q1 PMIC를 안전 관련 시스템에 통합하는 데 도움이 되는 정보를 자세히 설명합니다.
TPS65381x-Q1 장치는 차량용 및 산업용 시장에서 볼 수 있는 것과 같은 안전 관련 애플리케이션에서 마이크로컨트롤러(MCU)를 제공하도록 설계된 다중 레일 전원 공급 장치입니다. 이 장치는 TMS570 MCU와 C2000 마이크로컨트롤러 제품군과 듀얼 코어 락스탭(LS)이나 느슨하게 결합된 (...)
TIPA-050012 — TPS65381x-Q1 PMIC를 사용하는 TMS470 전원 공급 장치 설계
이 전원 공급 장치 설계는 TMS470에 전원을 공급하는 데 최적화된 전원 관리 IC를 설명하고, 개발자가 TPS65381x-Q1 PMIC를 안전 관련 시스템에 통합하는 데 도움이 되는 정보를 자세히 설명합니다.
TPS65381x-Q1 장치는 차량용 및 산업용 시장에서 볼 수 있는 것과 같은 안전 관련 애플리케이션에서 마이크로컨트롤러(MCU)를 제공하도록 설계된 다중 레일 전원 공급 장치입니다. 이 장치는 TMS570 MCU와 C2000 마이크로컨트롤러 제품군과 듀얼 코어 락스탭(LS)이나 느슨하게 결합된 아키텍처(LC)를 (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| HTSSOP (DAP) | 32 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.