홈 전력 관리 멀티 채널 IC(PMIC)
홈
전력 관리
멀티 채널 IC(PMIC)

TPS65084

활성

Braswell 프로세서용 프로그래머블 중간 입력 전압 범위 전원 관리 IC(PMIC)

지금 주문하기
데이터 시트

TPS65084

활성
데이터 시트 지금 주문하기

제품 상세 정보

Processor supplier Intel/Altera Processor name Braswell Product type Processor and FPGA Regulated outputs (#) 13 Step-down DC/DC converter 3 Step-up DC/DC converter 0 LDO 4 Vin (min) (V) 5.6 Vin (max) (V) 21 Vout (min) (V) -0.3 Vout (max) (V) 3.575 Iout (max) (A) 11 Configurability Factory programmable, Software configurable Features Comm control, Dynamic voltage scaling, Enable, Enable pin, I2C control, Overcurrent protection, Power good, Power sequencing, Synchronous rectification, Thermal shutdown, UVLO fixed Rating Catalog Operating temperature range (°C) -40 to 85 Step-down DC/DC controller 3 Step-up DC/DC controller 0 Iq (typ) (mA) 0.3 Switching frequency (max) (kHz) 3100 Shutdown current (ISD) (typ) (µA) 65 Switching frequency (typ) (kHz) 2500
Processor supplier Intel/Altera Processor name Braswell Product type Processor and FPGA Regulated outputs (#) 13 Step-down DC/DC converter 3 Step-up DC/DC converter 0 LDO 4 Vin (min) (V) 5.6 Vin (max) (V) 21 Vout (min) (V) -0.3 Vout (max) (V) 3.575 Iout (max) (A) 11 Configurability Factory programmable, Software configurable Features Comm control, Dynamic voltage scaling, Enable, Enable pin, I2C control, Overcurrent protection, Power good, Power sequencing, Synchronous rectification, Thermal shutdown, UVLO fixed Rating Catalog Operating temperature range (°C) -40 to 85 Step-down DC/DC controller 3 Step-up DC/DC controller 0 Iq (typ) (mA) 0.3 Switching frequency (max) (kHz) 3100 Shutdown current (ISD) (typ) (µA) 65 Switching frequency (typ) (kHz) 2500
VQFN (RSK) 64 64 mm² 8 x 8
  • Three Variable-Output Voltage Step-Down
    Controllers
    • Wide VIN Range From 5.4 V to 21 V
    • Up to 7-A Output Current for BUCK1 (VCC) and
      BUCK6 (VDDQ), and 11-A for BUCK2 (VGG)
      Using External FETs
    • I2C DVS Control (0.5 V to 1.45 V in 10-mV
      Steps) for BUCK1 and BUCK2
    • Pin-Selectable Output Voltages (1.2 V or
      1.35 V) for BUCK6 (VDDQ)
  • Three Variable-Output Voltage Synchronous Step-
    Down Converters
    • VIN Range From 4.5 V to 5.5 V
    • Up to 3.5 A of Output Current for BUCK3 (VNN)
      With I2C DVS Control (0.65 V to
      1.45 V in 25-mV Steps)
    • Up to 3 A of Output Current for BUCK4
      (V1P05A) and up to 1.5 A of Output Current for
      BUCK5 (V1P8A)
  • Three LDO Regulators With Adjustable Output
    Voltage
    • LDOA1: I2C-Selectable Output Voltage From
      1.35 V to 3.3 V for up to 200 mA of Output Current
    • LDOA2: I2C-Selectable Output Voltage From
      1.05 V, 1.1 V, 1.15 V, and 1.2 V
    • LDOA3: I2C-Selectable Output Voltage From
      1.1 V, 1.15 V, 1.2 V, and 1.24 V
  • VTT LDO for DDR3 and DDR4 Memory
    Termination
  • Three Load Switches With Slew Rate Control
    • Up to 300 mA of Output Current With Voltage
      Drop Less Than 1.5% of Nominal Input Voltage
    • RDSON < 96 mΩ at Input Voltage of 1.8 V
  • I2C Interface (Device Address 0x5E) Supports
    Standard Mode (100 kHz), Fast Mode (400 kHz),
    and Fast Mode Plus (1 MHz)
  • 64-Pin, Single-Row, 0.4-mm Pitch QFN Package
  • Three Variable-Output Voltage Step-Down
    Controllers
    • Wide VIN Range From 5.4 V to 21 V
    • Up to 7-A Output Current for BUCK1 (VCC) and
      BUCK6 (VDDQ), and 11-A for BUCK2 (VGG)
      Using External FETs
    • I2C DVS Control (0.5 V to 1.45 V in 10-mV
      Steps) for BUCK1 and BUCK2
    • Pin-Selectable Output Voltages (1.2 V or
      1.35 V) for BUCK6 (VDDQ)
  • Three Variable-Output Voltage Synchronous Step-
    Down Converters
    • VIN Range From 4.5 V to 5.5 V
    • Up to 3.5 A of Output Current for BUCK3 (VNN)
      With I2C DVS Control (0.65 V to
      1.45 V in 25-mV Steps)
    • Up to 3 A of Output Current for BUCK4
      (V1P05A) and up to 1.5 A of Output Current for
      BUCK5 (V1P8A)
  • Three LDO Regulators With Adjustable Output
    Voltage
    • LDOA1: I2C-Selectable Output Voltage From
      1.35 V to 3.3 V for up to 200 mA of Output Current
    • LDOA2: I2C-Selectable Output Voltage From
      1.05 V, 1.1 V, 1.15 V, and 1.2 V
    • LDOA3: I2C-Selectable Output Voltage From
      1.1 V, 1.15 V, 1.2 V, and 1.24 V
  • VTT LDO for DDR3 and DDR4 Memory
    Termination
  • Three Load Switches With Slew Rate Control
    • Up to 300 mA of Output Current With Voltage
      Drop Less Than 1.5% of Nominal Input Voltage
    • RDSON < 96 mΩ at Input Voltage of 1.8 V
  • I2C Interface (Device Address 0x5E) Supports
    Standard Mode (100 kHz), Fast Mode (400 kHz),
    and Fast Mode Plus (1 MHz)
  • 64-Pin, Single-Row, 0.4-mm Pitch QFN Package

The TPS650842 device is a single-chip solution, power-management IC designed specifically for the latest Intel™ processors targeted for tablets, ultrabooks, and notebooks with NVDC or non-NVDC power architectures, using 2S, 3S, or 4S Li-Ion battery packs. The TPS650842 device is used for essential systems with low-voltage rails merged for the smallest footprint and lowest-cost system-power solution. The TPS650842 device provides the complete power solution based on the Intel Reference Designs. Six highly efficient step-down voltage regulators (VRs), a sink or source LDO (VTT), two LDOs, and three load switches are controlled by power-up sequence logic to provide the proper power rails, sequencing, and protection—including DDR3 and DDR4 memory power. The three regulators (BUCK1–BUCK3) support dynamic voltage scaling (DVS) for maximum efficiency—including support for Connected Standby. The high-frequency VRs use small inductors and capacitors to achieve a small solution size. An I2C interface allows simple control by an embedded controller (EC) or by a system on chip (SoC). The PMIC comes in an 8-mm × 8-mm single-row QFN package with a thermal pad for good thermal dissipation and ease of board routing.

Use the following email address to request the full version of this data sheet: ipgmkt@list.ti.com.

The TPS650842 device is a single-chip solution, power-management IC designed specifically for the latest Intel™ processors targeted for tablets, ultrabooks, and notebooks with NVDC or non-NVDC power architectures, using 2S, 3S, or 4S Li-Ion battery packs. The TPS650842 device is used for essential systems with low-voltage rails merged for the smallest footprint and lowest-cost system-power solution. The TPS650842 device provides the complete power solution based on the Intel Reference Designs. Six highly efficient step-down voltage regulators (VRs), a sink or source LDO (VTT), two LDOs, and three load switches are controlled by power-up sequence logic to provide the proper power rails, sequencing, and protection—including DDR3 and DDR4 memory power. The three regulators (BUCK1–BUCK3) support dynamic voltage scaling (DVS) for maximum efficiency—including support for Connected Standby. The high-frequency VRs use small inductors and capacitors to achieve a small solution size. An I2C interface allows simple control by an embedded controller (EC) or by a system on chip (SoC). The PMIC comes in an 8-mm × 8-mm single-row QFN package with a thermal pad for good thermal dissipation and ease of board routing.

Use the following email address to request the full version of this data sheet: ipgmkt@list.ti.com.
filter 기타 멀티 채널 IC(PMIC) 찾기
다운로드 스크립트와 함께 비디오 보기 비디오
자세한 정보 및 샘플 가용성

전체 데이터 시트 및 기타 정보가 제공됩니다. 지금 요청

[RSK] 패키지가 샘플용으로 제공됩니다(TPS650842A0RSKT). 지금 요청

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하세요.
3개 모두 보기
상위 문서 유형 직함 형식 옵션 날짜
* Data sheet TPS650842 PMIC for Intel™ Braswell Platform datasheet PDF | HTML 2015/09/01
User guide TPS65084x Design Guide 2015/08/29
Application note TPS65084x Schematic Checklist, Layout Checklist, and ILIM Calculator Tool 2015/08/26

설계 및 개발

전원 공급 솔루션

TPS65084을 포함하는 솔루션을 살펴보세요. TI는 칩(SoC), 프로세서, 마이크로컨트롤러, 센서 또는 FPGA(Field Programmable Gate Array)의 TI와 비TI 시스템을 위한 전원 공급 솔루션을 제공합니다.

솔루션 보기
평가 모듈(EVM)용 GUI

IPG-UI — IPG-UI EVM GUI (Windows Installer)

The IPG-UI GUI can be used to configure multiple PMIC devices to evaluate the features and performance of those devices.  This GUI is built using web-based technologies and supports interacting with the EVM hardware using a USB2ANY adapter board. The USB2ANY Explorer is provided to allow (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어
다운로드
평가 모듈(EVM)용 GUI

IPG-UI-LINUX — IPG-UI EVM GUI (Linux Installer)

The IPG-UI GUI can be used to configure multiple PMIC devices to evaluate the features and performance of those devices.  This GUI is built using web-based technologies and supports interacting with the EVM hardware using a USB2ANY adapter board. The USB2ANY Explorer is provided to allow (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어
다운로드
평가 모듈(EVM)용 GUI

IPG-UI-OSX — IPG-UI EVM GUI (OSX Installer)

The IPG-UI GUI can be used to configure multiple PMIC devices to evaluate the features and performance of those devices.  This GUI is built using web-based technologies and supports interacting with the EVM hardware using a USB2ANY adapter board. The USB2ANY Explorer is provided to allow (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어
다운로드
평가 모듈(EVM)용 GUI

TPS65084X-GUI — TPS65084X device supporting file for IPG-UI

The user must first download IPG-UI before using this device supporting file for TPS65084X.
지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어
다운로드
패키지 핀 CAD 기호, 풋프린트 및 3D 모델
VQFN (RSK) 64 Ultra Librarian
TI의 평가 항목에 대한 표준 약관이 적용됩니다.

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

포럼 주제 모두 보기(영문)

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상