TCA6408A-Q1
- AEC-Q100 qualified for automotive applications
- Temperature grade 1: –40°C to +125°C, TA
- Functional Safety-Capable
- I2C to parallel port expander
- Operating power-supply voltage range of 1.65 V to 3.6 V
- Allows bidirectional voltage-level translation and GPIO expansion between 1.8-, 2.5-, and 3.3-V I2C bus and P-ports
- Low standby current consumption
- 400-kHz Fast I2C Bus
- Hardware address pin allows Two TCA6408A-Q1 devices on the same I2C/SMBus bus
- Active-low reset ( RESET) input
- Open-drain active-low interrupt ( INT) output
- Input and output configuration register
- Polarity inversion register
- Internal power-on reset
- Power up with all channels configured as inputs
- No glitch on power up
- Noise filter on SCL and SDA inputs
- Latched outputs with high-current drive maximum capability for directly driving LEDs
- Latch-up performance meets 100 mA per AEC Q100-004
- Schmitt-Trigger action allows slow input transition and better switching noise immunity at the SCL and SDA inputs
- ESD protection
- 2000-V Human body model (Q100-002)
- 1000-V Charged-device model (Q100-011)
The TCA6408A-Q1 is a 16-pin device that provides 8-bits of general purpose parallel input and output (I/O) expansion for the two-line bidirectional I2C bus (or SMBus) protocol. This device can operate with a power supply voltage ranging from 1.65 V to 3.6 V on both the I2C bus side (VCCI) and on the P-port side (VCCP). This allows the TCA6408A-Q1 to interface with next-generation microprocessors and microcontrollers on the SDA/SCL side, where supply levels are dropping down to conserve power. In contrast to the dropping power supplies of microprocessors and microcontrollers, some PCB components such as LEDs remain at a higher power supply.
The device supports both 100-kHz (Standard-mode) and 400-kHz (Fast-mode) clock frequencies. I/O expanders such as the TCA6408A-Q1 provide a simple solution when additional I/Os are needed for switches, sensors, push-buttons, LEDs, fans, and so forth.
관심 가지실만한 유사 제품
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | TCA6408A-Q1 Low-Voltage 8-Bit I2C and SMBus I/O Expander With Interrupt Output datasheet (Rev. A) | PDF | HTML | 2023. 2. 6 | |
| 애플리케이션 노트 | Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) | PDF | HTML | 2024. 7. 3 | ||
| 기능 안전 정보 | TCA6408A-Q1 Functional Safety FIT Rate, FMD and Pin FMA | PDF | HTML | 2020. 10. 29 | ||
| 애플리케이션 노트 | I2C Dynamic Addressing | 2019. 4. 25 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
IO-EXPANDER-EVM — IO-확장기-EVM: I2C 및 SMBus IO 확장기 평가 모듈
IO 확장기 평가 모듈(EVM)을 사용하면 TI의 SMBus 및 I2C IO 확장기 라인 디바이스 포트폴리오를 평가할 수 있습니다. TCA6424A 및 TCA9539는 보드에 설치됩니다. 24핀 TSSOP 풋프린트는TCA6408A, TCA6416A, TCA9534, TCA9534A, TCA9535, TCA9538, TCA9554, TCA9554A 및 TCA9555를 지원합니다.
SLVC564 — I/O Expander Software and Firmware Package
I2C-DESIGNER — I2C 디자이너 툴
TIDA-020060 — 100/1000Base-T1 이더넷 애플리케이션용 차량용 데이터 라인을 통한 전원 레퍼런스 설계
이 레퍼런스 설계는 차량용 사용 사례를 위한 PoDL(Power over Data Line) 구현을 보여줍니다. 이 설계는 100MBit/s 작동에 대해 DP83TG720S-Q1 1000MBit/s 단일 페어 이더넷(SPE) PHY를 사용하는 옵션으로 DP83TG720S-Q1 SPE PHY를 사용합니다. 커플링과 디커플링 네트워크는 최대 50W의 전력으로 결합하는데 사용됩니다.
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| TSSOP (PW) | 16 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.