SN6507-Q1
SN6507-Q1 has an internal oscillator to set the switching frequency of the power stage. As the two power switches are out of phase, the oscillator frequency is twice of the actual switching frequency of each power switch. The duty cycle is fixed with 70 ns deadtime to avoid shoot-through. The duty cycle is changeable if duty cycle feature is enabled. Please refer to Section 8.3.3.
SN6507-Q1 has a wide switching frequency range from 100 kHz up to 2 MHz, which is pin-programmable through a resistor (RCLK) to GND. Below table lists the value of RCLK to achieve certain operating frequencies (fSW). The choice of switching frequency is a trade-off between power efficiency and size of capacitive and inductive components. For example, when operating at higher switching frequency, the size of the transformer and inductor is reduced, resulting in a smaller design footprint and lower cost. However, higher frequency increases switching losses and consequently degrades the overall power supply efficiency.
Figure 8-6 can also be used to estimate the programmable switching frequency, fSW, using an external resistor value, RCLK, where RCLK is in kΩ and fSW is in kHz:
If CLK pin is shorted to GND, the part switches at its default frequency, FSW. CLK pin floating is not a valid state of operation and will cause the part to stop switching until an external clock signal is present.
The SN6507 -Q1 is a high voltage, high frequency push-pull transformer driver providing isolated power in a small solution size. The device comes with the push-pull topology’s benefits of simplicity, low EMI, and flux cancellation to prevent transformer saturation. Further space savings are achieved through duty-cycle control, which reduces component count for wide-input ranges, and by selecting a high switching frequency, reducing the size of the transformer.
The device integrates a controller and two 0.5-A NMOS power switches that switch out of phase. Its input operating range is programmed with precision undervoltage lockouts. The device is protected from fault conditions by over-current protection (OCP), adjustable under-voltage lockout (UVLO), over voltage lockout (OVLO), thermal shutdown (TSD), and break-before-make circuitry.
The programmable Soft Start (SS) minimizes inrush currents and provides power supply sequencing for critical power up requirements. Spread Spectrum Clocking (SSC) and pin-configurable Slew Rate Control (SRC) further reduces radiated and conducted emissions for ultra-low EMI requirements.
The SN6507 -Q1 is available in a 10-pin HVSSOP DGQ package. The device operation is characterized for a temperature range from –55°C to 125°C.
관심 가지실만한 유사 제품
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 | |
|---|---|---|---|---|---|---|
| * | 데이터 시트 | SN6507-Q1 Low-Emissions, 36-V Push-Pull Transformer Driver with Duty Cyle Control for Isolated Power Supplies datasheet | PDF | HTML | 2021. 2. 15 | ||
| Application brief | Optimized Excitation Power Stage for Electrically Excited Synchronous Machines (Rev. A) | PDF | HTML | 2026. 5. 5 | |||
| 백서 | Isolated Bias Power Supply Architecture for HEV/EV Single Stage Onboard Chargers | PDF | HTML | 2026. 1. 7 | |||
| 기술 문서 | How isolated bias transformer parasitic capacitance impacts EMI performance | PDF | HTML | 2025. 9. 22 | |||
| 백서 | Isolated Bias Power Supply Architecture for HEV/EV HVLV DCDC Converters | PDF | HTML | 2025. 1. 16 | |||
| 백서 | Isolated Bias Power Supply Architecture for HEV and EV Onboard Chargers | PDF | HTML | 2024. 11. 27 | |||
| 기능 안전 정보 | SN6507-Q1 Functional Safety FIT Rate, FMD and Pin FMA | PDF | HTML | 2022. 5. 16 | |||
| 애플리케이션 노트 | How to Reduce Emissions in Push-Pull Isolated Power Supplies (Rev. A) | PDF | HTML | 2021. 10. 5 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
SN6507DGQEVM — SN6507 평가 모듈 - 저방출, 500mA 푸시-풀 절연 전원 공급 장치
SN6507DGQEVM을 사용하면 절연 전원 공급 장치 애플리케이션에서 SN6507 푸시-풀 절연 변압기 드라이버의 성능과 기능을 평가할 수 있습니다.
PMP31182 — 4가지 토폴로지를 사용하는 절연 바이어스 전원 공급 장치 레퍼런스 설계
이 레퍼런스 설계는 PSR 플라이백, 푸시-풀, LLC 공진 및 절연 DCDC 모듈과 같은 다양한 토폴로지를 사용하는 4가지 절연 바이어스 전원 공급 장치 설계를 보여줍니다. 이러한 토폴로지는 구체적인 이점을 제공하지만 동시에 절충을 해야 합니다. 이러한 토폴로지를 충분히 비교할 수 있도록 4개의 하드웨어 설계를 사용하여 전기 매개 변수를 가능한 한 유사하게 유지하면서 수행됩니다. 이러한 설계의 입력 및 출력 전압은 15V이고 최대 부하 전류는 100mA입니다.
PMP41078 — GaN HEMT를 지원하는 고전압-저전압 DC-DC 컨버터 레퍼런스 설계
이 레퍼런스 설계는 650V 질화 갈륨(GaN) 하이 전자 모빌리티 트랜지스터(HEMT)를 지원하는 3.5kW 고전압-저전압 DC 컨버터를 설명합니다. LMG3522R030을 기본 스위치로 사용하여 컨버터는 높은 스위칭 주파수에서 작동합니다. 이 설계에서 컨버터는 더 작은 크기의 변압기를 사용합니다. 액티브 클램핑 금속 산화물 반도체 전계 효과 트랜지스터(MOSFET)의 열 성능을 완화하기 위해 컨버터는 2채널 액티브 클램핑 회로를 사용합니다.
PMP41139 — 3.5kW, 800V~14V DC/DC 컨버터 레퍼런스 설계
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| HVSSOP (DGQ) | 10 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.