MSPM0G3708
80MHz Arm® Cortex®-M0+ MCU, 24비트 7 SD-ADC, 256KB 플래시 32KB SRAM, CAN-FD, UART 4개, SPI 2개, I2C 2개
MSPM0G3708
- Core
- Arm 32-bit Cortex M0+ CPU with memory protection unit, frequency up to 80MHz
- Operating characteristics
- Extended temperature: –40°C up to 125°C
- Digital Supply voltage range: 1.62V to 3.6V
- Analog Supply voltage range: 2.7V to 3.6V
- Memories
- Up to 256KB of flash memory with error correction code (ECC)
- Dual-bank with address swap for OTA updates
- 8KB data flash bank with ECC protection
- 32KB total SRAM with ECC protection or hardware parity
- Up to 256KB of flash memory with error correction code (ECC)
- High-performance analog peripherals
- Sigma delta
sub-system (SDSS) with 7 simultaneous sampling 24-bit, delta-sigma (ΔΣ),
analog-to-digital converters (SDADC) with differential inputs
- > 100 dB dynamic range at gain= 1 at 4kSps ADC data rate
- 32kSps max ADC data rate.
-
Integrated negative charge pump allows input signals below ground
- Integrated 1.2V voltage reference with low temperature drift (max 20 ppm/°C)
- Up to two simultaneous sampling 12-bit 1.6Msps, SAR analog-to-digital converters (ADC) with up to 7 external channels
- Up to two high-speed comparators (COMP) with integrated 8-bit reference DACs
- 32ns propagation delay in high-speed mode
- Support low-power mode operation down to <1µA
- Programmable analog connections between SAR ADC and COMP
-
Two voltage references (VREF) for 12-bit SAR ADC
-
Configurable 1.4V or 2.5V internal shared voltage reference with external VREF capacitor
-
Configurable 1.4V or 2.5V internal only voltage reference without external VREF capacitor
-
- Integrated temperature sensor
- Sigma delta
sub-system (SDSS) with 7 simultaneous sampling 24-bit, delta-sigma (ΔΣ),
analog-to-digital converters (SDADC) with differential inputs
- Optimized low-power modes
- RUN: 104µA/MHz (CoreMark, executed from flash)
- SLEEP: 614uA at 4MHz
- STOP: 56µA at 32kHz
- STANDBY: 1.4µA at 32kHz with RTC and SRAM state retention
- SHUTDOWN: 69nA with IO wake-up capability
- Intelligent digital peripherals
- 9-channel DMA controller
- Math accelerator supports DIV, SQRT, MAC and TRIG computations
- Five timers support up to 18 PWM channels
- One 16-bit general-purpose timers support QEI
- Two 16-bit general-purpose timers support low-power operation in STANDBY mode
- Two 16-bit advanced timers with deadband support and complimentary outputs up to 12 PWM channels
-
Two basic software timers including 4 independent configurable 16-bit counters each
-
Ability to daisy-chain 2 of the 16-bit counters to form a 32-bit counter
-
Ability to generate 2x interrupt driven PWMs per basic software timer
-
- Two windowed watchdog timers (WWDT), one independent watchdog timer (IWDT)
- RTC with alarm and calendar mode
- Enhanced communication interfaces
-
Five configurable serial interfaces (UNICOMM)
- One configurable serial interface supporting UART or SPI
-
One configurable serial interfaces supporting UART (with LIN) or I2C (controller or target mode)
-
One configurable serial interfaces supporting UART or I2C (controller or target mode)
-
One dedicated UART + LIN interface
-
One dedicated SPI interface up to 32Mbits/s
-
One Controller Area Network (CAN) interface supporting CAN 2.0 A or B and CAN-FD
-
- Clock system
- Internal 4 to 32MHz oscillator (SYSOSC) with up to ±3% accuracy
- Phase-locked loop (PLL) up to 80MHz
- Internal 32kHz low-frequency oscillator (LFOSC) with ±3% accuracy
- External 4 to 48MHz crystal oscillator (HFXT)
- External 32kHz crystal oscillator (LFXT)
- External clock input
- Data integrity and encryption
- AES-128/256 accelerator with support for GCM/GMAC, CCM/CBC-MAC, CBC, CTR
- Secure key storage for up to four AES keys
- Flexible firewalls for protecting code and data
- Cyclic redundancy checker (CRC-16, CRC-32)
- Flexible I/O features
- Up to 18 GPIOs
- Two 5V-tolerant open-drain IOs
- One high-drive IO with 20mA drive strength
- One high-speed IO
- Up to 18 GPIOs
- Development support
- 2-pin serial wire debug (SWD)
- Package options
-
40-pin VQFN (ZFU) (0.5mm pitch) (LGA carrier)
-
- Family members (also see Device Comparison)
- MSPM0G1708: 256KB flash, 32KB RAM, 8KB Databank, 7 x SDADC, 2x SAR ADC, 2x COMP, Advanced Timers
- MSPM0G3708: 256KB flash, 32KB RAM, 8KB Databank, 7 x SDADC, 2x SAR ADC, 2x COMP, Advanced Timers, 1x CAN-FD
- MSPM0G1737: 128KB flash, 32KB RAM, 8KB Databank, 7 x SDADC, 1x SAR ADC
- MSPM0G3737: 128KB flash, 32KB RAM, 8KB Databank, 7 x SDADC, 1x SAR ADC, 1x CAN-FD
- Development kits and software (also see Tools and Software)
-
LP-MSPM0G3708 Launchpad Development Kit
- MSPM0 Software Development Kit (SDK)
-
MSPM0x708 and MSPM0x737 microcontrollers (MCUs) are part of the MSP highly integrated, low-power 32-bit MCU family based on the enhanced Arm Cortex-M0+ 32-bit core platform, operating at up to 80MHz frequency. These MCUs offer a blend of cost optimization and design flexibility for applications requiring 128KB to 256KB of flash memory in a 40 pin package device. These devices include CAN-FD controllers, cybersecurity enablers, high performance integrated analog, and provide excellent low-power performance across the operating temperature range.
The device has up to 256KB of embedded flash program memory with built-in error correction code (ECC) and up to 32KB SRAM (with ECC and parity protection). The flash memory is organized into two main banks to support field firmware updates, with address swap support provided between the two main banks.
Flexible cybersecurity enablers can be used to support secure boot, secure in-field firmware updates, IP protection (execute-only memory), key storage, and more. Hardware acceleration is provided for a variety of AES symmetric cipher modes.
Sigma Delta Sub-system (SDSS) contains seven simultaneously sampling, 24-bit, delta-sigma (ΔΣ), analog-to-digital converters (ADC), offers wide dynamic range, low power, and energy-measurement-specific features, making the device an excellent fit for energy metering, power metrology, medical and test and measurement applications. The ADC inputs can be directly interfaced to a resistor divider network or a power transformer to measure voltage or to a current transformer or a Rogowski coil to measure current. A low-drift, 1.2-V reference is integrated into the AFE sub-system
The individual ADC channels can be independently configured depending on the sensor input. A low-noise, programmable gain amplifier (PGA) provides gains ranging from 1 to 128 to amplify low-level signals. Additionally, this device integrates channel to channel phase calibration and offset and gain calibration registers to help remove signal-chain errors.
A set of high performance analog modules is provided, such as two simultaneously sampling 12-bit, 1.6Msps ADCs supporting up to 7 external channels, on-chip voltage reference (1.4V or 2.5V), and two comparators operable in low-power and high-speed modes with additional built-in 8-bit reference DACs.
The TI MSPM0 family of low-power MCUs consists of devices with varying degrees of analog and digital integration. The MSPM0 MCU platform combines the Arm Cortex-M0+ platform with a holistic ultra-low-power system architecture, allowing system designers to increase performance while reducing energy consumption.
MSPM0x708 and MSPM0x737 MCUs are supported by an extensive hardware and software ecosystem with reference designs and code examples to get the design started quickly. Development kits include a LaunchPad and EVM available for purchase. TI also provides a free MSPM0 Software Development Kit (SDK), which is available as a component of Code Composer Studio™ IDE desktop and cloud version within the TI Resource Explorer. MSPM0 MCUs are also supported by extensive online collateral, training with MSP Academy, and online support through the TI E2E™ support forums.
For complete module descriptions, see the MSPM0 G-Series 80MHz Microcontrollers Technical Reference Manual.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | MSPM0x708, MSPM0x737 Mixed-Signal Microcontrollers with 7 Sigma-Delta ADCs and CAN-FD Interface datasheet | PDF | HTML | 2026. 10. 15 | |
| * | 사용 설명서 | MSPM0 G-Series 80-MHz Microcontrollers Technical Reference Manual (Rev. F) | PDF | HTML | 2026. 11. 5 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
LP-MSPM0G3708 — MSPM0G3708 LaunchPad™ 개발 키트
The MSPM0G3708 LaunchPad™ development kit is an evaluation module for the MSPM0G3708 microcontroller (MCU). The LaunchPad kit contains everything needed to start development on the MSPM0Gx70x and MSPM0Gx73x microcontroller platform, including an onboard debug probe for programming, debugging, (...)
MSPM0-SDK — MSPM0 Software Development Kit (SDK)
MSPM0 SDK는 단일 소프트웨어 패키지 아래에 있는 MSPM0 MCU 플랫폼용 애플리케이션 개발을 가속화하는 궁극의 소프트웨어, 툴 및 문서 모음을 제공합니다.
MSPM0-ZEPHYR-SDK — Zephyr SDK for MSPM0 Devices
MSPM0 SDK는 단일 소프트웨어 패키지 아래에 있는 MSPM0 MCU 플랫폼용 애플리케이션 개발을 가속화하는 궁극의 소프트웨어, 툴 및 문서 모음을 제공합니다.
CCSTUDIO — Code Composer Studio integrated development environment (IDE)
CCStudio™ IDE is an integrated development environment designed for Texas Instruments' embedded processors, available as both a desktop and cloud-based application. It is an integral part of TI's extensive CCStudio™ development ecosystem.
CCStudio IDE is built on Eclipse Theia™ framework, the (...)
CCSTUDIO-OPENOCD — OpenOCD Binary Releases
MSP-ZERO-CODE-STUDIO — Graphical development environment for designing applications for MSP microcontrollers
MSP Zero Code Studio는 펌웨어 개발을 간소화하는 시각적 설계 환경으로, 코딩과 IDE 없이 짧은 시간 내에 마이크로컨트롤러 애플리케이션을 구성, 개발 및 실행할 수 있습니다. 독립적으로 다운로드하여 사용하거나, 클라우드에서 사용할 수 있습니다.
SYSCONFIG — Standalone desktop version of SysConfig
CCStudio™ SysConfig is part of TI's extensive CCStudio™ development ecosystem and is a configuration tool that simplifies hardware and software configuration challenges to accelerate software development.
SysConfig provides an intuitive graphical user interface for configuring pins, peripherals, (...)
MSPM0-ACADEMY — MSPM0™ academy
CCSTUDIO-STARTHUB — Example application browser
MSP-MOTOR-CONTROL — MSPM0 Firmware solutions for motor control applications
MSP 모터 제어는 MSPM0 Arm® Cortex® M0+ MCU 및 인기 있는 모터 드라이버 솔루션으로 30분 이내에 모터를 구동하는 소프트웨어, 툴 및 예제 모음입니다.
MSP 모터 제어는 성능, 통합 및 사용 편의성에 최적화된 센서드 및 센서리스 제어 알고리즘을 사용하여 브러시드, 스테퍼 및 3상 모터를 구동하는 지원되는 하드웨어 키트에 대한 예제를 제공합니다. 지금 하드웨어를 주문하고, 모터를 연결하고, 당사의 그래픽 사용자 인터페이스나 온라인 코드 예제를 사용하여 모터를 회전시켜 보십시오.
TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud
ENERGY-METROLOGY-STUDIO-DESIGN — Secure release for TI Energy Metrology Studio graphical configuration tool
LP-MSPM0G3507-OOBE — Out-of-box experience GUI for LP-MSPM0G3507
MSPM0-ANALOG-CONFIGURATOR — Analog Configurator for MSPM0
MSPM0 아날로그 구성 도구는 기존의 코딩 개발이 필요 없는 MSPM0 장치를 사용하여 아날로그 신호 체인 설계를 간소화하고 활성화를 가속화하도록 설계된 그래픽 구성 툴입니다.
이 툴은 직관적인 GUI를 사용하여 MSPM0 장치의 높은 아날로그 통합으로 신호 체인을 구성하고, 실시간으로 신호를 분석 및 플롯하며, 장치를 플래싱하는 데 필요한 구성 및 코드를 생성합니다.
MSP-GANG-SOFTWARE — MSP-GANG Software
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash는 TI의 광범위한 CCStudio™ 개발 에코시스템의 일부로, TI 마이크로컨트롤러 및 무선 연결 장치의 온칩 플래시와 TI 프로세서의 온보드 플래시를 프로그래밍하기 위한 소프트웨어 도구입니다. UniFlash는 그래픽 및 명령줄 인터페이스를 모두 제공하며, 데스크톱 또는 클라우드 환경에서 실행할 수 있습니다.
UniFlash는 CCStudio™ 개발자 영역의 클라우드에서 실행하거나 Windows®, Linux®, macOS® 컴퓨터에서 다운로드해 사용할 수 있습니다.
macOS는 mmWave, AMx, K2G 및 (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| LGA (ZFU) | 40 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.