이 제품의 최신 버전이 있습니다
비교 대상 장치와 유사한 기능
MSP430FR2355
- Embedded microcontroller
- 16-bit RISC architecture up to 24 MHz
- Extended temperature: –40°C to 105°C
- Wide supply voltage range from 3.6 V down to 1.8 V (operational voltage is restricted by SVS levels, see VSVSH- and VSVSH+ in PMM, SVS and BOR)
- Optimized low-power modes (at 3 V)
- Active mode: 142 µA/MHz
- Standby:
- LPM3 with 32768-Hz crystal: 1.43 µA (with SVS enabled)
- LPM3.5 with 32768-Hz crystal: 620 nA (with SVS enabled)
- Shutdown (LPM4.5): 42 nA (with SVS disabled)
- Low-power ferroelectric RAM (FRAM)
- Up to 32KB of nonvolatile memory
- Built-in error correction code (ECC)
- Configurable write protection
- Unified memory of program, constants, and storage
- 1015 write cycle endurance
- Radiation resistant and nonmagnetic
- Ease of use
- 20KB ROM library includes driver libraries and FFT libraries
- High-performance analog
- One 12-channel 12-bit analog-to-digital converter (ADC)
- Internal shared reference (1.5, 2.0, or 2.5 V)
- Sample-and-hold 200 ksps
- Two enhanced comparators (eCOMP)
- Integrated 6-bit digital-to-analog converter (DAC) as reference voltage
- Programmable hysteresis
- Configurable high-power and low-power modes
- One with fast 100-ns response time
- One with 1-µs response time with 1.5-µA low power
- Four smart analog combo (SAC-L3) (MSP430FR235x devices only)
- Supports General-Purpose Operational Amplifier (OA)
- Rail-to-rail input and output
- Multiple input selections
- Configurable high-power and low-power modes
- Configurable PGA mode supports
- Noninverting mode: ×1, ×2, ×3, ×5, ×9, ×17, ×26, ×33
- Inverting mode: ×1, ×2, ×4, ×8, ×16, ×25, ×32
- Built-in 12-bit reference DAC for offset and bias settings
- 12-bit voltage DAC mode with optional references
- One 12-channel 12-bit analog-to-digital converter (ADC)
- Intelligent digital peripherals
- Three 16-bit timers with three capture/compare registers each (Timer_B3)
- One 16-bit timer with seven capture/compare registers each (Timer_B7)
- One 16-bit counter-only real-time clock counter (RTC)
- 16-bit cyclic redundancy checker (CRC)
- Interrupt compare controller (ICC) enabling nested hardware interrupts
- 32-bit hardware multiplier (MPY32)
- Manchester codec (MFM)
- Enhanced serial communications
- Two enhanced USCI_A (eUSCI_A) modules support UART, IrDA, and SPI
- Two enhanced USCI_B (eUSCI_B) modules support SPI and I2C
- Clock system (CS)
- On-chip 32-kHz RC oscillator (REFO)
- On-chip 24-MHz digitally controlled oscillator (DCO) with frequency locked loop (FLL)
- ±1% accuracy with on-chip reference at room temperature
- On-chip very low-frequency 10-kHz oscillator (VLO)
- On-chip high-frequency modulation oscillator (MODOSC)
- External 32-kHz crystal oscillator (LFXT)
- External high-frequency crystal oscillator up to 24 MHz (HFXT)
- Programmable MCLK prescaler of 1 to 128
- SMCLK derived from MCLK with programmable prescaler of 1, 2, 4, or 8
- General input/output and pin functionality
- 44 I/Os on 48-pin package
- 32 interrupt pins (P1, P2, P3, and P4) can wake MCU from LPMs
- Development tools and software (also see Tools and Software)
- LaunchPad™ development kit (MSP‑EXP430FR2355)
- Target development board (MSP‑TS43048PT)
- Free professional development environments
- Family members (also see Device Comparison)
- MSP430FR2355: 32KB of program FRAM, 512 bytes of data FRAM, 4KB of RAM
- MSP430FR2353: 16KB of program FRAM, 512 bytes of data FRAM, 2KB of RAM
- MSP430FR2155: 32KB of program FRAM, 512 bytes of data FRAM, 4KB of RAM
- MSP430FR2153: 16KB of program FRAM, 512 bytes of data FRAM, 2KB of RAM
- Package options
- 48-pin: LQFP (PT)
- 40-pin: VQFN (RHA)
- 38-pin: TSSOP (DBT)
- 32-pin: VQFN (RSM)
MSP430FR215x and MSP430FR235x microcontrollers (MCUs) are part of the MSP430™ MCU value line portfolio of ultra-low-power low-cost devices for sensing and measurement applications. MSP430FR235x MCUs integrate four configurable signal-chain modules called smart analog combos, each of which can be used as a 12-bit DAC or a configurable programmable-gain Op-Amp to meet the specific needs of a system while reducing the BOM and PCB size. The device also includes a 12-bit SAR ADC and two comparators. The MSP430FR215x and MSP430FR235x MCUs all support an extended temperature range from –40° up to 105°C, so higher temperature industrial applications can benefit from the devices FRAM data-logging capabilities. The extended temperature range allows developers to meet requirements of applications such as smoke detectors, sensor transmitters, and circuit breakers.
The MSP430FR215x and MSP430FR235x MCUs feature a powerful 16-bit RISC CPU, 16-bit registers, and a constant generator that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the device to wake up from low-power modes to active mode typically in less than 10 µs.
The MSP430 ultra-low-power (ULP) FRAM microcontroller platform combines uniquely embedded FRAM and a holistic ultra-low-power system architecture, allowing system designers to increase performance while lowering energy consumption. FRAM technology combines the low-energy fast writes, flexibility, and endurance of RAM with the nonvolatile behavior of flash.
MSP430FR215x and MSP430FR235x MCUs are supported by an extensive hardware and software ecosystem with reference designs and code examples to get your design started quickly. Development kits include the MSP-EXP430FR2355 LaunchPad™ development kit and the MSP-TS430PT48 48-pin target development board. TI also provides free MSP430Ware™ software, which is available as a component of Code Composer Studio™ IDE desktop and cloud versions within TI Resource Explorer. The MSP430 MCUs are also supported by extensive online collateral, training, and online support through the E2E™ support forums.
For complete module descriptions, see the MSP430FR4xx and MSP430FR2xx Family Users Guide.
추가 정보
TI 개발자 영역을 방문하여 평가 및 개발을 시작하십시오.
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
ALGO-3P-UISP1-TI — 텍사스 인스트루먼트 장치용 Algocraft μISP1 프로그래머
μISP는 호스트 PC(RS-232, USB, LAN 연결 기능이 내장되어 있음)에 연결되어 작동하거나 단독 모드로 작동할 수 있습니다.
독립 실행형 모드의 프로그래밍 싸이클은 단순히 START 버튼을 누르거나 일부 TTL 제어 라인을 통해 실행될 수 있습니다.
컴팩트한 크기와 다양한 기능을 갖추고 있어 생산 환경, 수동 및 자동 프로세스에 간편하게 통합할 수 있습니다.
MSP-EXP430FR2355 — MSP430FR2355 LaunchPad™ 개발 키트
MSP-EXP430FR2355 LaunchPad™개발 키트는 MSP430FR2355 밸류 라인 MCU(마이크로컨트롤러) 기반의 사용하기 쉬운 평가 모듈(EVM)입니다. 프로그래밍, 디버깅 및 에너지 측정을 위한 온보드 디버그 프로브를 포함하여 MSP430FR2x 밸류 라인 MCU 플랫폼에서 개발을 시작하는 데 필요한 모든 것이 포함되어 있습니다. 이 보드에는 간단한 사용자 인터페이스를 만들 수 있는 2개의 버튼 및 2개의 LED가 포함되어 있습니다. 또한 주변광 센서와 외부 아날로그 소스를 위한 커넥터도 있습니다.
(...)
MSP-TS430PT48 — MSP430FR2355 MCU - 48핀용 타깃 개발 보드(마이크로컨트롤러 포함 안 됨)
참고: 이 키트에는 MSP430™ 마이크로컨트롤러(MCU) 샘플이 포함되어 있지 않습니다. 호환되는 장치의 샘플을 받으려면 제품 페이지를 방문하거나 TI 스토어 카트에 툴을 추가한 후 관련 MCU를 선택하세요.
MSP430FR2355.
MSP-TS430PT48는 JTAG 인터페이스 또는 Spy Bi-Wire(2회선 JTAG) 프로토콜을 통해 시스템 내 MSP430을 프로그래밍 및 디버깅하는 데 사용되는 독립 실행형 ZIF 소켓 타깃 보드입니다. 이 개발 보드는 48핀 QFP 패키지(TI 패키지 코드: PN)의 (...)
MSP-FET — MSP MCU 프로그래머 및 디버거
MSP-FET는 디버그 프로브라고도 하는 강력한 에뮬레이션 개발 도구로, 사용자가 MSP 저전력 마이크로컨트롤러(MCU)에서 신속하게 개발을 시작할 수 있게 해줍니다.
JTAG 및 SBW 인터페이스 모두에서 프로그래밍과 실시간 디버깅을 지원합니다. 또한 MSP-FET는 컴퓨터 USB 인터페이스와 MSP UART 간의 백채널 UART 연결도 제공합니다. 이를 통해 MSP 프로그래머는 MSP와 컴퓨터에서 실행되는 단자 간에 직렬로 통신하는 편리한 방법을 사용할 수 있습니다. 또한 UART 및 I2C 통신 프로토콜을 통해 (...)
ALGO-3P-WRITENOW — Algocraft WriteNow! 프로그래머
WriteNow! 시스템 내 프로그래머 시리즈는 프로그래밍 산업에서 획기적인 발전입니다. 프로그래머는 다양한 제조업체의 수많은 장치(마이크로컨트롤러, 메모리, CPLD 및 기타 프로그래머블 장치)를 지원하며 간편한 ATE/장치 통합을 위한 컴팩트한 크기를 가지고 있습니다. 이는 단독으로 작동하거나 호스트 PC(RS-232, LAN 및 USB 연결 기능이 내장되어 있음)에 연결되어 있으며 사용이 간편한 소프트웨어 유틸리티가 제공됩니다.
MSP-FRAM-UTILITIES — FRAM embedded software utilities for MSP ultra-low-power microcontrollers
The Texas Instruments FRAM Utilities is designed to grow as a collection of embedded software utilities that leverage the ultra-low-power and virtually unlimited write endurance of FRAM. The utilities are available for MSP430FRxx FRAM microcontrollers and provide example code to help start (...)
지원되는 제품 및 하드웨어
제품
MSP430 microcontrollers
MSPFRBOOT — MSPFRBOOT
The bootloader (BSL) on MSP430™ microcontrollers (MCUs) lets users communicate with embedded memory in the MSP MCUs during the prototyping phase, final production, and in service. This is done through standard interfaces such as UART, I2C, SPI, and USB. Both the programmable memory (Flash/FRAM) and (...)
지원되는 제품 및 하드웨어
제품
MSP430 microcontrollers
TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud
지원되는 제품 및 하드웨어
제품
Arm Cortex-M0+ MCU
MSP430 microcontrollers
Arm Cortex-R MCU
C2000 실시간 마이크로컨트롤러
Sub-1GHz 무선 MCU
저전력 2.4GHz 제품
차량용 무선 커넥티비티 제품
차량용 mmWave 레이더 센서
산업용 mmWave 레이더 센서
차량용 운전자 지원 SoC
오디오 및 레이더 DSP SoC
멀티미디어 및 산업용 네트워킹 SoC
하드웨어 개발
도터 카드
평가 보드
CCSTUDIO — Code Composer Studio integrated development environment (IDE)
Code Composer Studio is an integrated development environment (IDE) for TI's microcontrollers and processors. It is comprised of a rich suite of tools used to build, debug, analyze and optimize embedded applications. Code Composer Studio is available across Windows®, Linux® and macOS® platforms.
(...)
지원되는 제품 및 하드웨어
이 설계 리소스는 이러한 범주의 제품 대부분을 지원합니다.
제품 세부 정보 페이지에서 지원을 확인하십시오.
-
parametric-filter 마이크로프로세서 및 DSP -
parametric-filter Microcontrollers -
parametric-filter Wi-Fi 제품 -
parametric-filter 저전력 2.4GHz 제품 -
parametric-filter 신호 조절기 -
parametric-filter mmWave 레이더 센서
ENERGYTRACE — EnergyTrace 기술
As most developers know, it is difficult to (...)
IAR-KICKSTART — IAR Embedded Workbench
주요 구성 요소:
- 프로젝트 관리 툴과 편집기가 포함된 통합 개발 환경입니다.
- 고도로 최적화된 C 및 C++ 컴파일러.
- 다중 파일 컴파일 지원.
- 런타임 라이브러리.
- 링커 (...)
MSP430-ACADEMY — MSP430™ academy
지원되는 제품 및 하드웨어
제품
MSP430 microcontrollers
하드웨어 개발
평가 보드
개발 키트
WHIS-3P-SAFERTOS — WITTENSTEIN SAFERTOS 사전 인증 안전 RTOS
MSP-GANG-SOFTWARE — MSP-GANG Software
지원되는 제품 및 하드웨어
제품
Arm Cortex-M0+ MCU
MSP430 microcontrollers
하드웨어 개발
평가 보드
개발 키트
UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors
UniFlash is a software tool for programming on-chip flash on TI microcontrollers and wireless connectivity devices and on-board flash for TI processors. UniFlash provides both graphical and command-line interfaces.
UniFlash can be run from the cloud on the TI Developer Zone or downloaded and used (...)
지원되는 제품 및 하드웨어
제품
C2000 실시간 마이크로컨트롤러
산업용 mmWave 레이더 센서
차량용 mmWave 레이더 센서
MSP430 microcontrollers
Wi-Fi 제품
Arm Cortex-M4 MCU
Arm Cortex-M0+ MCU
Arm Cortex-R MCU
저전력 2.4GHz 제품
차량용 무선 커넥티비티 제품
Sub-1GHz 무선 MCU
오디오 및 레이더 DSP SoC
멀티미디어 및 산업용 네트워킹 SoC
SLAC740 — MSP430FR235x, MSP430FR215x Code Examples
지원되는 제품 및 하드웨어
제품
MSP430 microcontrollers
SLAC807 — MCT8316ZTEVM MSP430FR2355 GUI Firmware
지원되는 제품 및 하드웨어
제품
MSP430 microcontrollers
하드웨어 개발
평가 보드
CIRCUIT0020 — 트랜스임피던스 증폭기 회로
CIRCUIT060001 — 단일 전원, 저압측, 단방향 전류 센싱 회로
CIRCUIT060002 — NTC 서미스터 회로를 사용한 온도 감지
CIRCUIT060003 — PTC 서미스터 회로를 사용한 온도 감지
CIRCUIT060004 — 저잡음 및 장거리 PIR 센서 컨디셔너 회로
CIRCUIT060005 — 개별 차동 증폭기 회로를 사용한 고압측 전류 감지
CIRCUIT060006 — 브리지 증폭기 회로
CIRCUIT060007 — 저압측 양방향 전류 감지 회로
CIRCUIT060009 — 반파 정류기 회로
CIRCUIT060089 — MSP430 스마트 아날로그 콤보를 지원하는 단일 공급, 저압측, 단방향 전류 감지 회로
CIRCUIT060090 — MSP430™ 스마트 아날로그 콤보를 지원하는 온도 감지 음극 온도 계수(NTC) 회로
CIRCUIT060091 — MSP430 스마트 아날로그 콤보를 지원하는 온도 감지 양극 온도 계수(PTC) 회로
CIRCUIT060092 — MSP430 스마트 아날로그 콤보를 지원하는 저잡음 및 장거리 패시브 적외선 센서 컨디셔너 회로
CIRCUIT060093 — MSP430 스마트 아날로그 콤보를 지원하는 고압측 전류 감지 회로 설계
CIRCUIT060094 — MSP430 스마트 아날로그 콤보를 지원하는 단일 공급 스트레인 게이지 브리지 증폭기 회로
CIRCUIT060095 — MSP430 스마트 아날로그 콤보를 지원하는 저압측 양방향 전류 감지 회로
CIRCUIT060096 — MSP430 스마트 아날로그 콤보를 지원하는 반파 정류기 회로
CIRCUIT060097 — MSP430 스마트 아날로그 콤보를 지원하는 트랜스임피던스 증폭기 회로
MSP-3P-SEARCH — MSP 타사 검색 도구
(...)
TIDM-01000 — MSP430 스마트 아날로그 콤보를 지원하는 4~20mA 루프 전원 공급 RTD 온도 트랜스미터 레퍼런스 설계
TIDA-010019 — 온도 센서에 냉접점 보상을 제공하기 위한 RTD 교체 레퍼런스 설계
TIDA-010056 — 3상 BLDC 드라이브를 위한 54V, 1.5kW, >99% 효율, 70x69mm2 전력계 레퍼런스 설계
TIDA-010031 — 25.2V, 30A 고속 무센서(>100krpm) 브러시리스 DC 모터 드라이브 레퍼런스 설계
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| LQFP (PT) | 48 | Ultra Librarian |
| TSSOP (DBT) | 38 | Ultra Librarian |
| VQFN (RHA) | 40 | Ultra Librarian |
| VQFN (RSM) | 32 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치