BQ27621-G1
- Single-Cell Li-Ion Battery Fuel Gauge
- Resides on System Board
- Supports Embedded or Removable Batteries
- Powered Directly from Battery with Integrated
LDO
- Easy To Configure Fuel Gauging Based on the
Dynamic Voltage Correlation Algorithm- Reports Remaining Capacity and State of
Charge (SOC) with Smoothing Filter - Automatically Adjusts for Self-Discharge,
Temperature, and Rate Changes
- Reports Remaining Capacity and State of
- Microcontroller Peripheral Supports:
- 400-kHz I2C Serial Interface
- Configurable SOC Interrupt or
Battery Low Digital Output Warning - Internal Temperature Sensor or
Host Reported Temperature
- Support 4.2-V, 4.3-V, and 4.35-V Chemistries
- 9-pin 1.62 × 1.58 mm, 0.5 mm pitch YZF package
The Texas Instruments bq27621-G1 is a minimally configured microcontroller peripheral that provides system-side fuel gauging for single-cell Li-Ion batteries. The device requires very little user configuration and system microcontroller firmware development.
The bq27621-G1 uses the Dynamic Voltage Correlation algorithm for fuel gauging. This process eliminates the need for a sense resistor when calculating remaining battery capacity (mAh), state-of-charge (%), battery voltage (mV), and temperature (°C).
Battery fuel gauging with the bq27621-G1 requires connections only to PACK+ (P+) and PACK– (P–) for a removable battery pack or embedded battery circuit. The tiny 9-pin, 1.62 mm × 1.58 mm, 0.5 mm pitch YZF package is ideal for space-constrained applications.
관심 가지실만한 유사 제품
비교 대상 장치와 동일한 기능을 지원하는 핀 대 핀.
기술 자료
| 상위 문서 | 유형 | 직함 | 형식 옵션 | 최신 영어 버전 다운로드 | 날짜 |
|---|---|---|---|---|---|
| * | 데이터 시트 | bq27621-G1 System-Side Fuel Gauge With Dynamic Voltage Correlation datasheet (Rev. E) | PDF | HTML | 2016. 1. 6 | |
| 사용 설명서 | BQ27621-G1 Technical Reference Manual (Rev. C) | 2014. 8. 1 | |||
| 사용 설명서 | Quick Start Guide for bq27621-G1 (Rev. A) | 2014. 1. 20 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
BQ27621EVM-G1 — 시스템 측 연료(가스) 게이지 동적 전압 상관 관계 평가 모듈
The BQ27621EVM-G1A evaluation module is a complete evaluation system for the bq27621-G1. The EVM includes one bq27621-G1 circuit module using DVC algorithm. The bq27621-G1 should be used with batteries with a charge voltage from 4.2 volts to 4.35 volts. A separate orderable EV2300 or (...)
EV2400 — 배터리 연료(가스) 게이지용 USB 기반 PC 인터페이스 평가 모듈
The EV2400 EVM interface board enables an IBM-compatible or other type PC (with the required driver for its particular platform) to communicate with the Texas Instruments SMBus or I2C interface gas gauges via a Universal Serial Bus (USB) port. In addition to this board, PC software is required to (...)
BQSTUDIO-STABLE — Battery Management Studio (bqStudio) Software – stable version downloads for bq series of TI battery fuel gauges
bqStudio(Battery Management Studio)는 TI 배터리 관리 제품의 평가, 설계, 구성, 테스트 또는 기타 활용 프로세스를 지원하는 견고한 종합 툴을 제공합니다. 여기에는 실시간 감시, 그래프 및 로깅 지원, 명령 전송을 위한 간편한 인터페이스, 직접 저수준 통신 및 I/O, 구성, 보정, 학습 주기 수행, 장치를 생산 단계로 가져가기 위한 유용한 파일 생성 등 레지스터 및 데이터 메모리에 대한 전체 액세스를 제공하는 기능은 물론, 자동화된 가이드 지원도 포함됩니다.
bq20xxx 및 bq30xxx와 같은 (...)
BQSTUDIO-TEST — Battery Management Studio (bqStudio) Software – untested version downloads
bqStudio(Battery Management Studio)는 TI 배터리 관리 제품의 평가, 설계, 구성, 테스트 또는 기타 활용 프로세스를 지원하는 견고한 종합 툴을 제공합니다. 여기에는 실시간 감시, 그래프 및 로깅 지원, 명령 전송을 위한 간편한 인터페이스, 직접 저수준 통신 및 I/O, 구성, 보정, 학습 주기 수행, 장치를 생산 단계로 가져가기 위한 유용한 파일 생성 등 레지스터 및 데이터 메모리에 대한 전체 액세스를 제공하는 기능은 물론, 자동화된 가이드 지원도 포함됩니다.
bq20xxx 및 bq30xxx와 같은 (...)
GPCCHEM — 게이징 매개 변수 계산기: Impedance Track 게이지의 화학 성분 일치
실온 또는 저온 성능을 최적화하기 전에 IT(Impedance Track) 알고리즘 가스 게이지에 대한 GPC 화학 ID 일치(가장 가까운 화학 일치 찾기)를 수행해야 합니다.
게이징 매개 변수 계산기 임피던스 트랙 가스 게이지에 대한 화학 ID 일치(GPCCHEM)는 배터리 설계자가 특정 배터리 프로파일에 대해 일치하는 화학 ID를 얻는 데 도움이 되는 수학 계산 및 시뮬레이션 툴입니다. 화학 ID는 텍사스 인스트루먼트에서 정의하며 bqStudio(Battery Management Studio)를 사용하여 프로그래밍할 수 (...)
GPCRA0 — 게이징 매개 변수 계산기: Impedance Track 게이지를 위한 실내 온도 성능 최적화
Gauging Parameter Calculator – Optimize room temperature performance for Impedance track gas gauges (GPCRA0) / Golden GG Maker is a math calculation tool that helps the battery designer to refine the Impedance Track battery gauge parameters for a given battery profile. It provides optimized (...)
BQ27XXXSW-LINUX — BQ27XXX용 Linux 드라이버
The Linux driver supports the BQ27x series of Battery Fuel Gauges. The Linux driver supports communication through the I2C/HDQ bus and interfaces with the power supply sub-system to monitor battery properties.
Linux Mainline Status
Available in Linux Main line: Yes
Available through git.ti.com: N/A
(...)
BQEVSW-MKST-UPDATE — Software Update to enable BQEVSW to use MKST-3P-ALT-EV2300
BQ-BATTERY-PROGRAMMER-SW 소프트웨어 개발 키트(SDK)는 TI 배터리 관리 제품을 사용하는 팩의 프로그래밍, 테스트 또는 조립 프로세스를 지원하는 강력한 소프트웨어 명령줄 툴 모음입니다. 이 소프트웨어의 실행 파일은 EV2300 통신 트랜스시버용 MKST-3P-ALT-EV2300 MKS 기술 대안과 함께 작동합니다. 실행 파일은 단일 스테이션에서 작동하지만 MKS Technology Inc.의 추가 소프트웨어 및 GUI를 사용하여 여러 스테이션으로 확장할 수 있습니다. 이 소프트웨어에는 여러 스테이션에 대한 (...)
TIDA-00252 — 전압 기반 가스 게이지 레퍼런스 디자인
The Texas Instruments bq27621-G1 is an easy to configure microcontroller peripheral that provides system-side fuel gauging for single-cell Li-ion batteries. This device requires minimal user configuration and system microntroller development. The design will provide State of Charge indication for (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| DSBGA (YZF) | 9 | Ultra Librarian |
주문 및 품질
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.