TUSB9261-Q1

AKTIV

Brücke der 2. Generation, von SuperSpeed USB 3.0 nach Serial ATA, für die Automobilindustrie

Jetzt bestellen

Datenblatt

document-pdfAcrobat TUSB9261-Q1 USB 3.0 to SATA Bridge datasheet (Rev. A) (Englisch)

TUSB9261-Q1

AKTIV

Datenblatt

Jetzt bestellen

Produktdetails

Type

Bridge

Function

USB3

USB speed (bps)

5000000000

Alternate mode

No

Rating

Automotive

Operating temperature range (°C)

-40 to 85

Type

Bridge

Function

USB3

USB speed (bps)

5000000000

Alternate mode

No

Rating

Automotive

Operating temperature range (°C)

-40 to 85

HTQFP (PAP)

64

144 mm² (12 mm × 12 mm)

Qualified for Automotive Applications
AEC-Q100 Qualified with the Following Exceptions:
- Device CDM ESD Classification Level C3
Ideal for bridging Serial ATA (SATA) Devices, Such
as Hard Disk Drives (HDD), Solid State Drives (SSD),
or Optical Drives (OD) to Universal Serial Bus (USB)
USB Interface
- Integrated Transceiver Supports SS/HS/FS Signaling
- Best in Class Adaptive Equalizer
  - Allows for Greater Jitter Tolerance in the Receiver
- USB Class Support
  - USB Attached SCSI Protocol (UASP) for HDD and SSD
  - USB Mass Storage Class Bulk-Only Transport (BOT)
    Including Support for Error Conditions Per the
    13 Cases (Defined in the BOT Specification)
  - USB Bootability Support
  - USB Human Interface Device (HID)
- Supports Firmware Update Via USB Using a TI Provided Application
SATA Interface
- Serial ATA Specification Revision 2.6 Supporting gen1 and
  gen2 Data Rates
- Supports hot plug
- Supports Mass-Storage Devices Compatible with the ATA/ATAPI-8
  Specification
Integrated ARM Cortex M3 Core
- Customizable Application Code Loaded From EEPROM Via SPI Interface
- Two Additional SPI Port Chip Selects for Peripheral Connection
- Up to 5 GPIOs for End-User Configuration via HID
- Serial Communications Interface for Debug (UART)
General Features
- Integrated Spread Spectrum Clock Generation Enables Operation
  from a Single Low Cost Crystal or Clock Oscillator
  - Supports 20, 25, 30 or 40 MHz
- JTAG Interface for IEEE1149.1 and IEEE1149.6 Boundary Scan
- Available in a Fully RoHS Compliant Package (PAP)

Qualified for Automotive Applications
AEC-Q100 Qualified with the Following Exceptions:
- Device CDM ESD Classification Level C3
Ideal for bridging Serial ATA (SATA) Devices, Such
as Hard Disk Drives (HDD), Solid State Drives (SSD),
or Optical Drives (OD) to Universal Serial Bus (USB)
USB Interface
- Integrated Transceiver Supports SS/HS/FS Signaling
- Best in Class Adaptive Equalizer
  - Allows for Greater Jitter Tolerance in the Receiver
- USB Class Support
  - USB Attached SCSI Protocol (UASP) for HDD and SSD
  - USB Mass Storage Class Bulk-Only Transport (BOT)
    Including Support for Error Conditions Per the
    13 Cases (Defined in the BOT Specification)
  - USB Bootability Support
  - USB Human Interface Device (HID)
- Supports Firmware Update Via USB Using a TI Provided Application
SATA Interface
- Serial ATA Specification Revision 2.6 Supporting gen1 and
  gen2 Data Rates
- Supports hot plug
- Supports Mass-Storage Devices Compatible with the ATA/ATAPI-8
  Specification
Integrated ARM Cortex M3 Core
- Customizable Application Code Loaded From EEPROM Via SPI Interface
- Two Additional SPI Port Chip Selects for Peripheral Connection
- Up to 5 GPIOs for End-User Configuration via HID
- Serial Communications Interface for Debug (UART)
General Features
- Integrated Spread Spectrum Clock Generation Enables Operation
  from a Single Low Cost Crystal or Clock Oscillator
  - Supports 20, 25, 30 or 40 MHz
- JTAG Interface for IEEE1149.1 and IEEE1149.6 Boundary Scan
- Available in a Fully RoHS Compliant Package (PAP)

The TUSB9261-Q1 is an ARM cortex M3 microcontroller based Universal Serial Bus (USB) 3.0 to Serial ATA (SATA) bridge. It provides the necessary hardware and firmware to implement a USB Attached SCSI Protocol (UASP) compliant mass storage device suitable for bridging SATA compatible hard disk drives (HDD) and solid state disk drives (SSD) to a USB 3.0 bus. The firmware also implements the mass storage class bulk-only transport (BOT) for bridging optical drives and other compatible SATA devices to the USB bus. In addition to UASP and BOT support,a USB human interface device (HID) interfaces is supported for control of the general purpose input/ouput (GPIO). The SATA interface supports gen1 (1.5-Gbps) and gen2 (3.0-Gbps) for cable lengths up to 2 meters.

The device is available in a 64-pin HTQFP package and is designed for operation over the industrial temperature range of –40°C to 85°C.

The TUSB9261-Q1 is an ARM cortex M3 microcontroller based Universal Serial Bus (USB) 3.0 to Serial ATA (SATA) bridge. It provides the necessary hardware and firmware to implement a USB Attached SCSI Protocol (UASP) compliant mass storage device suitable for bridging SATA compatible hard disk drives (HDD) and solid state disk drives (SSD) to a USB 3.0 bus. The firmware also implements the mass storage class bulk-only transport (BOT) for bridging optical drives and other compatible SATA devices to the USB bus. In addition to UASP and BOT support,a USB human interface device (HID) interfaces is supported for control of the general purpose input/ouput (GPIO). The SATA interface supports gen1 (1.5-Gbps) and gen2 (3.0-Gbps) for cable lengths up to 2 meters.

The device is available in a 64-pin HTQFP package and is designed for operation over the industrial temperature range of –40°C to 85°C.

filter

Andere USB-PHYs und Brücken suchen

Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.

Alle anzeigen 6

Top-Dokumentation	Typ	Titel	Datum
*	Datenblatt	TUSB9261-Q1 USB 3.0 to SATA Bridge datasheet (Rev. A)	31.01.2014
*	Errata	TUSB9261 Errata (Rev. B)	20.12.2012
	Anwendungshinweis	TUSB9261 Implementation Guide (Rev. E)	09.12.2014
	Benutzerhandbuch	TUSB9261 DEMO User's Guide (Rev. A)	09.12.2014
	Benutzerhandbuch	TUSB9260 Flash Burner - User Guide (Rev. D)	24.10.2013
	Benutzerhandbuch	TUSB926x SpeedBoost Monitor User's Guide	23.09.2010

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

TUSB9261DEMO — TUSB9261 Demo- und Referenzdesign

The TUSB9261DEMO board is a bridge between a SuperSpeed USB (USB 3.0) bus and a Serial–ATA (SATA) development kit. The TUSB9261DEMO is used to evaluate system compatibility. It provides a TUSB9261 hardware for connection to a SATA device such as a solid state drive, hard disk drive, DVD (...)