Home Audio, Haptik und Piezo Audiowandler Audio-CODECs
Home
Audio, Haptik und Piezo
Audiowandler
Audio-CODECs

TAC5242

AKTIV

Hardware-gesteuertes Stereo-Audio-Codec mit DAC mit 119 dB Dynamikbereich und DAC mit 120 dB Dynamik

Jetzt bestellen
Datenblatt

TAC5242

AKTIV
Jetzt bestellen

Produktdetails

Number of ADC channels 2 Number of DAC channels 2 Digital audio interface I2S, L, TDM Control interface H/W Analog inputs 2 Analog outputs 2 Features High Dynamic Range, High-performance, Low latency, Low power, Mic bias, Phase-locked loop (PLL), Pin control, Single supply, Stereo headphone amplifier Sampling rate (max) (kHz) 192 Rating Catalog ADC SNR (typ) (dB) 119 DAC SNR (typ) (dB) 120 Operating temperature range (°C) -40 to 125
Number of ADC channels 2 Number of DAC channels 2 Digital audio interface I2S, L, TDM Control interface H/W Analog inputs 2 Analog outputs 2 Features High Dynamic Range, High-performance, Low latency, Low power, Mic bias, Phase-locked loop (PLL), Pin control, Single supply, Stereo headphone amplifier Sampling rate (max) (kHz) 192 Rating Catalog ADC SNR (typ) (dB) 119 DAC SNR (typ) (dB) 120 Operating temperature range (°C) -40 to 125
VQFN (RGE) 24 16 mm² (4 mm × 4 mm)
  • Stereo audio ADC Channels
    • Performance:
      • Line/Microphone differential input dynamic range: 119dB
      • Differential input THD+N: –98dB
    • Input voltage:
      • Differential, 2VRMS full-scale inputs
      • Single-ended, 1VRMS full-scale inputs
    • ADC sample rates (fS) = 8kHz to 192kHz
    • Digital HPF with configurable cut-off frequency:
      • 1Hz or 12Hz, at 48kHz sampling rate
    • Low noise microphone bias
  • Stereo audio DAC Channels
    • Performance:
      • DAC to differential line-out dynamic range: 120 dB
      • DAC to pseudo-differential headphone-out dynamic range: 110 dB
      • THD+N: –100 dB
    • Output voltage:
      • Differential line-out/receiver, 2VRMS full-scale
      • Pseudo-differential headphone, 1VRMS full-scale
      • Single-ended line-out, 1VRMS full-scale
    • DAC sample rates (fs) = 8kHz to 192kHz
  • Common Features
    • Pin or Hardware Control
    • Audio Serial Interface
      • Format: TDM, I2S, or Left-justified (LJ)
      • Bus Controller and Target Modes
      • Configurable TDM Slots
      • Word Length: Selectable 24 or 32 Bits
    • Pin-selectable digital decimation/interpolation filter options:
      • Linear-phase or Low-latency
    • Integrated PLL
    • Auto clock & sample rate detection
    • Interrupt output on clock error
    • Single Supply Operation AVDD: 1.8V or 3.3V
    • I/O Supply Operation: 1.8V or 3.3V
    • Temperature grade 1: –40°C ≤ TA ≤ +125°C
  • Stereo audio ADC Channels
    • Performance:
      • Line/Microphone differential input dynamic range: 119dB
      • Differential input THD+N: –98dB
    • Input voltage:
      • Differential, 2VRMS full-scale inputs
      • Single-ended, 1VRMS full-scale inputs
    • ADC sample rates (fS) = 8kHz to 192kHz
    • Digital HPF with configurable cut-off frequency:
      • 1Hz or 12Hz, at 48kHz sampling rate
    • Low noise microphone bias
  • Stereo audio DAC Channels
    • Performance:
      • DAC to differential line-out dynamic range: 120 dB
      • DAC to pseudo-differential headphone-out dynamic range: 110 dB
      • THD+N: –100 dB
    • Output voltage:
      • Differential line-out/receiver, 2VRMS full-scale
      • Pseudo-differential headphone, 1VRMS full-scale
      • Single-ended line-out, 1VRMS full-scale
    • DAC sample rates (fs) = 8kHz to 192kHz
  • Common Features
    • Pin or Hardware Control
    • Audio Serial Interface
      • Format: TDM, I2S, or Left-justified (LJ)
      • Bus Controller and Target Modes
      • Configurable TDM Slots
      • Word Length: Selectable 24 or 32 Bits
    • Pin-selectable digital decimation/interpolation filter options:
      • Linear-phase or Low-latency
    • Integrated PLL
    • Auto clock & sample rate detection
    • Interrupt output on clock error
    • Single Supply Operation AVDD: 1.8V or 3.3V
    • I/O Supply Operation: 1.8V or 3.3V
    • Temperature grade 1: –40°C ≤ TA ≤ +125°C

The TAC5242 is a high-performancelow-power stereo audio codec with 2VRMS differential input, 119dB dynamic range ADC and 2VRMS differential output, 120dB dynamic range DAC. The TAC5242 supports both differential and single-ended inputs and outputs. The ADC supports both line/microphone input signals with options for AC or DC coupling configurations and the DAC output can be configured for either line-output or headphone loads. The DAC can drive upto 62.5mW into a 16Ω headphone load. The device integrates a phase-locked loop (PLL) and supports sample rates up to 192kHz for both the ADC and DAC signal chains. The device also integrates a DC-removal digital high-pass filter (HPF) with configurable cut-off for the ADC signal chain. The TAC5242 supports time-division multiplexing (TDM), left-justified (LJ), or I2S audio formats in controller and target modes, and is pin or hardware controlled. These integrated high-performance features, pin control along with a single supply operation, make TAC5242 an excellent choice for space-constrained audio applications.

The TAC5242 is a high-performancelow-power stereo audio codec with 2VRMS differential input, 119dB dynamic range ADC and 2VRMS differential output, 120dB dynamic range DAC. The TAC5242 supports both differential and single-ended inputs and outputs. The ADC supports both line/microphone input signals with options for AC or DC coupling configurations and the DAC output can be configured for either line-output or headphone loads. The DAC can drive upto 62.5mW into a 16Ω headphone load. The device integrates a phase-locked loop (PLL) and supports sample rates up to 192kHz for both the ADC and DAC signal chains. The device also integrates a DC-removal digital high-pass filter (HPF) with configurable cut-off for the ADC signal chain. The TAC5242 supports time-division multiplexing (TDM), left-justified (LJ), or I2S audio formats in controller and target modes, and is pin or hardware controlled. These integrated high-performance features, pin control along with a single supply operation, make TAC5242 an excellent choice for space-constrained audio applications.

filter Andere Audio-CODECs suchen
Herunterladen Video mit Transkript ansehen Video

Ähnliche Produkte, die für Sie interessant sein könnten

open-in-new Alternativen vergleichen
Selbe Funktionalität wie der verglichene Baustein bei gleicher Anschlussbelegung.
TAC5212 AKTIV Hochleistungs-Stereo-Codec für die Automobilindustrie mit 119 dB A/D-Wandler mit Dynamikbereich und Software-controlled version

Technische Dokumentation

Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 5
Top-Dokumentation Typ Titel Format-Optionen Neueste englische Version herunterladen Datum
* Datenblatt TAC5242 Hardware-control stereo audio codec with 119 dB dynamic range ADC and 120 dB dynamic range DAC datasheet (Rev. A) PDF | HTML 05.11.2024
Anwendungshinweis How to Reduce Noise in Audio Data Converters PDF | HTML 14.07.2026
Anwendungshinweis Clocking Configuration of Device and Flexible Clocking For TAx5x1x Family (Rev. A) PDF | HTML 05.09.2024
Anwendungshinweis Analog Input Configurations, Mixing and Muxing of TAx5x1x Devices (Rev. A) PDF | HTML 15.05.2024
Product overview Audio ADC, DAC, and CODEC for Professional Audio and Music Applications PDF | HTML 13.02.2024

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

TAC5242EVM-K — TAC5242 – Evaluierungsmodul

Das TAC5242EVM-K-Evaluierungsmodul (EVM) ermöglicht es Ihnen, die Fähigkeiten unseres TAC5242 zu testen. Es ist ein hardwaregesteuerter Zwei-Kanal-Hochleistungs-Stereo-Codec, der für Anwendungen in den Bereichen Mobilfunk, IP-Telefonie oder professionelle Audioanwendungen vorgesehen ist. Das (...)
Benutzerhandbuch: PDF | HTML
Unterstützte Produkte und Hardware
Vorrätig
Limit:
??asset.out-of-stock-ti_de_DE??
Nicht verfügbar
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
VQFN (RGE) 24 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Empfohlene Produkte können Parameter, Evaluierungsmodule oder Referenzdesigns zu diesem TI-Produkt beinhalten.

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos