ZHCSL90A August 2020 – May 2026 TPS25980
PRODUCTION DATA
| 参数 | 测试条件 | 最小值 | 典型值 | 最大值 | 单位 | |
|---|---|---|---|---|---|---|
| 输入电源 (IN) | ||||||
| VIN | 输入电压范围 | 2.7 | 24 | V | ||
| IQ | IN 静态电流 | VEN ≥ VUVLO(R) | 800 | 1200 | µA | |
| ISD | IN 关断电流 | VSD < VEN < VUVLO | 204 | 300 | µA | |
| VEN < VSD | 3.67 | 20 | µA | |||
| VUVP | IN 欠压保护阈值 | VIN 上升 | 2.46 | 2.53 | 2.6 | V |
| VIN 下降 | 2.35 | 2.42 | 2.49 | V | ||
| 过压保护 (IN) | ||||||
| VOVP(R) | 过压保护阈值 | TPS259802x,VIN 上升 | 3.62 | 3.7 | 3.76 | V |
| TPS259803x,VIN 上升 | 7.39 | 7.6 | 7.76 | V | ||
| TPS259804x,VIN 上升 | 16.32 | 16.9 | 17.31 | V | ||
| VOVP(F) | TPS259802x,VIN 下降 | 3.52 | 3.6 | 3.66 | V | |
| TPS259803x,VIN 下降 | 7.22 | 7.4 | 7.55 | V | ||
| TPS259804x,VIN 下降 | 15.80 | 16.4 | 16.81 | V | ||
| 输出电流监测器 (IMON) | ||||||
| GIMON | 电流监测器增益 (IIMON:IOUT) | 3A ≤ IOUT ≤ min(8A, ILIM) | 228.78 | 246 | 263.22 | µA/A |
| 输出电流限制 (ILIM) | ||||||
| ILIM | IOUT 电流限制阈值 | RILIM = 773Ω,TJ = 25°C | 1.76 | 2 | 2.17 | A |
| RILIM = 773Ω,TJ = -40 至 125°C | 1.53 | 2 | 2.43 | A | ||
| RILIM = 300Ω,TJ = 25°C | 4.75 | 4.98 | 5.23 | A | ||
| RILIM = 300Ω,TJ = -40 至 125°C | 4.36 | 4.98 | 5.66 | A | ||
| RILIM = 182Ω,TJ = 25°C | 7.77 | 8.13 | 8.54 | A | ||
| RILIM = 182Ω,TJ = -40 至 125°C | 7.23 | 8.13 | 9.07 | A | ||
| RILIM = 开路 | 0 | A | ||||
| ICB | ILIM 引脚短接至 GND 条件下(单点失效)的 IOUT 断路器阈值 | RILIM = 短接至 GND,TJ = 25℃ | 20 | A | ||
| ISC | 短路快速跳变阈值 | 210 | % ILIM | |||
| 导通电阻 (IN - OUT) | ||||||
| RON | 导通状态电阻 | TJ = 25°C,IOUT = 2A | 3 | mΩ | ||
| TJ = -40 至 125℃,IOUT = 2A | 5 | mΩ | ||||
| 使能/欠压锁定 (EN/UVLO) | ||||||
| VUVLO(R) | EN/UVLO 引脚电压阈值 | VEN 上升 | 1.18 | 1.2 | 1.23 | V |
| VUVLO(F) | VEN 下降 | 1.08 | 1.1 | 1.13 | V | |
| VSD | 最低关断电流的 EN/UVLO 引脚电压阈值 | VEN 下降 | 0.59 | 0.8 | V | |
| IENLKG | EN/UVLO 引脚泄漏电流 | 0.1 | µA | |||
| 电源正常状态指示 (PG) | ||||||
| VPGD | PG 引脚低电压(PG 置为无效) | VIN < VUVP,VEN < VSD,IPG = 26µA | 651 | 786 | mV | |
| VIN = 3.3V,IPG ≤ 5mA | 320 | mV | ||||
| VIN ≥ 5V,IPG ≤ 5mA | 100 | mV | ||||
| IPGLKG | PG 引脚泄漏电流(PG 置为有效) | PG 通过 10kΩ 上拉至 5V | 1.7 | µA | ||
| RON(PGA) | PG 置为有效时的 RON | 4.2 | mΩ | |||
| VPGTHD | PG 置为无效时的 VIN - VOUT 阈值 | 0.224 | 0.326 | 0.450 | V | |
| 自动重试延迟间隔 (RETRY_DLY) | ||||||
| VRETRY_DLY(R) | RETRY_DLY 振荡器比较器阈值 | 1.1 | V | |||
| VRETRY_DLY(F) | 0.35 | V | ||||
| VRETRY_DLY_HYS | RETRY_DLY 振荡器磁滞 | 0.65 | 0.75 | 0.85 | V | |
| IRETRY_DLY | RETRY_DLY 引脚偏置电流 | 1.7 | 2.05 | 2.5 | µA | |
| 自动重试次数 (NRETRY) | ||||||
| VNRETRY(R) | NRETRY 振荡器比较器阈值 | 1.1 | V | |||
| VNRETRY(F) | 0.35 | V | ||||
| VNRETRY_HYS | NRETRY 振荡器磁滞 | 0.65 | 0.75 | 0.85 | V | |
| INRETRY | NRETRY 引脚偏置电流 | 1.7 | 2.05 | 2.5 | µA | |
| 电流故障计时器 (ITIMER) | ||||||
| IITIMER | ITIMER 放电电流 | ISC > IOUT > ILIM | 1.4 | 2.1 | 2.8 | µA |
| RITIMER | ITIMER 内部上拉电阻 | IOUT < ILIM | 23 | kΩ | ||
| VINT | ITIMER 引脚默认电压 | IOUT < ILIM | 2.5 | V | ||
| VITIMER | ITIMER 比较器下降阈值 | ISC > IOUT > ILIM,ITIMER 电压上升 | 1.53 | V | ||
| ΔVITIMER | ITIMER 比较器电压阈值差值 | ISC > IOUT > ILIM,ITIMER 电压下降 | 0.7 | 0.98 | 1.3 | V |
| LDSTRT | ||||||
| VLDSTRT | LDSTRT 上升阈值 | LDSTRT 电压上升 | 1.1 | 1.21 | 1.3 | V |
| ILDSTRT | LDSTRT 充电电流 | PG 置为有效 | 1.7 | 2.05 | var tiPageName = 'Literature reader-ZHCSL90A-zh_CN'; var tiDocType = 'Data Sheet'; var tiLibraryStore = new com.TI.tiLibrary.tiLibraryStore(); var tiLibraryViewerStore = tiLibraryStore.viewer_store; RiotControl.addStore(tiLibraryStore); var subRoutes = riot.route.create(); subRoutes("/document-viewer/*/datasheet/*\\?*#*", function(gpn, url, params, anchor) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + gpn + "/datasheet/" + url + "#" + anchor, toc: true, set_content: true }); }); subRoutes("/document-viewer/*/datasheet/*#*", function(gpn, url, anchor) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + gpn + "/datasheet/" + url + "#" + anchor, toc: true, set_content: true }); }); subRoutes("/document-viewer/*/datasheet/*", function(gpn, url) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + gpn + "/datasheet/" + url, toc: true, set_content: true }); }); subRoutes("/document-viewer/*/*/datasheet/*\\?*#*", function(locale, gpn, url, params, anchor) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + locale + "/" + gpn + "/datasheet/" + url + "#" + anchor, toc: true, set_content: true }); }); subRoutes("/document-viewer/*/*/datasheet/*#*", function(locale, gpn, url, anchor) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + locale + "/" + gpn + "/datasheet/" + url + "#" + anchor, toc: true, set_content: true }); }); subRoutes("/document-viewer/*/*/datasheet/*", function(locale, gpn, url) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + locale + "/" + gpn + "/datasheet/" + url, toc: true, set_content: true }); }); subRoutes("/document-viewer/*/datasheet#*/*", function(gpn, url, fragment) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + gpn + "/datasheet#" + url + "/" + fragment, toc: true, set_content: true }); }); subRoutes("/document-viewer/*/*/datasheet#*/*", function(locale, gpn, url, fragment) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + locale + "/" + gpn + "/datasheet#" + url + "/" + fragment, toc: true, set_content: true }); }); subRoutes("/document-viewer/lit/html/*", function(litnum) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/lit/html/" + litnum, toc: true, set_content: true }); }); subRoutes("/document-viewer/lit/html/*/*\\?*#*", function(litnum, url, params, anchor) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/lit/html/" + litnum + "/" + url + "#" + anchor, toc: true, set_content: true }); }); subRoutes("/document-viewer/lit/html/*/*#*", function(litnum, url, anchor) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/lit/html/" + litnum + "/" + url + "#" + anchor, toc: true, set_content: true }); }); subRoutes("/document-viewer/lit/html/*#*/*", function(litnum, url, anchor) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/lit/html/" + litnum + "#" + url + "/" + anchor, toc: true, set_content: true }); }); subRoutes("/document-viewer/*/lit/html/*#*/*", function(locale, litnum, url, anchor) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + locale + "/lit/html/" + litnum + "#" + url + "/" + anchor, toc: true, set_content: true }); }); subRoutes("/document-viewer/lit/html/*/*", function(litnum, url) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/lit/html/" + litnum + "/" + url, toc: true, set_content: true }); }); subRoutes("/document-viewer/*/lit/html/*/*\\?*#*", function(locale, litnum, url, params, anchor) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + locale + "/lit/html/" + litnum + "/" + url + "#" + anchor, toc: true, set_content: true }); }); subRoutes("/document-viewer/*/lit/html/*/*#*", function(locale, litnum, url, anchor) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + locale + "/lit/html/" + litnum + "/" + url + "#" + anchor, toc: true, set_content: true }); }); subRoutes("/document-viewer/*/lit/html/*/*", function(locale, litnum, url) { RiotControl.trigger("ti_library_open_viewer", { document: tiLibraryViewerStore.document, documentLocale: tiLibraryViewerStore.documentLocale, url: "/document-viewer/" + locale + "/lit/html/" + litnum + "/" + url, toc: true, set_content: true }); }); var compose_url = function(q) { //URL format: scheme:[//[user[:password]@]host[:port]][/path][?query][#fragment] var tempUrl = q.url.replace("//www.ti.com.cn/", ""); var url = tempUrl.replace("//www.ti.com.cn/", ""); if (q.search != null) { var params = ""; var hash = ""; var url_parts = url.split('#'); if (url_parts.length == 2) { url = url_parts[0]; hash = url_parts[1]; } var param_parts = url.split('?'); if (param_parts.length == 2) { url = param_parts[0]; var parsed_params = param_parts[1].split('&'); var keyword_param_found = false; for (var i = 0; i < parsed_params.length; i++) { if (parsed_params[i].indexOf('search=') == 0) { keyword_param_found = true; parsed_params[i] = 'search=' + q.search; } } if (!keyword_param_found) { parsed_params.push('search=' + q.search); } params = parsed_params.join('&'); } else { params = 'search=' + q.search; } if (params > "") { url = url + '?' + params; } if (hash > "") { url = url + '#' + hash; } } return url; }; tiLibraryViewerStore.compose_url_route = function(location, q) { return compose_url(q); }; tiLibraryViewerStore.compute_content_href = function(href, url) { return url; }; tiLibraryViewerStore.compose_topic_url = function(location, q) { return compose_url(q); }; tiLibraryViewerStore.important_notice_url = "//www.ti.com.cn/document-viewer/cn/lit/html/ZHCSL90A/important_notice#ImpNotice001"; var ods_reader = riot.mount('ti-library-viewer', { store: tiLibraryStore.list_store, viewerstore: tiLibraryViewerStore }); riot.route.base('/'); riot.route.start(true); compute_document_locale = function(docName) { var locale = 'en_US'; if (docName) { if (docName.toLowerCase().indexOf('z')===0) { locale = 'zh_CN'; } else if (docName.toLowerCase().indexOf('j') == 0) { locale = 'ja_JP'; } } return locale; } open_reader = function() { var path = window.location.pathname.split('/'); var path_minus_filename = ''; for (var i = 0; i < path.length - 1; i++) { if (i == 0 && path[i] == '') { console.log("double slashes found in beginning of document path; treating document path as local machine path"); continue; } path_minus_filename += "/" + path[i]; } RiotControl.trigger("ti_library_open_viewer", { documentLocale: compute_document_locale( "ZHCSL90A"), document: { href: path_minus_filename, lit_num: "ZHCSL90A", doc_type: "Data Sheet", show_toc: "true", translated_doc_type: "数据表", gpn: "", title: "TPS25980:具有集成热插拔保护和可调节瞬态故障管理功能的 2.7-24V、8A、3mΩ 智能电子保险丝", disclaimer: "本资源的原文使用英文撰写。 为方便起见,TI 提供了译文;由于翻译过程中可能使用了自动化工具,TI 不保证译文的准确性。 为确认准确性,请务必访问 ti.com 参考最新的英文版本(控制文档)。 ", product: "//www.ti.com.cn/product/cn/", email: 'mailto:?subject=ZHCSL90A TPS25980:具有集成热插拔保护和可调节瞬态故障管理功能的 2.7-24V、8A、3mΩ 智能电子保险丝&body=http://www.ti.com.cn/document-viewer/cn/lit/html/ZHCSL90', download: '//www.ti.com.cn/cn/lit/pdf/ZHCSL90A', tistore: '//store.ti.com/Search.aspx?k=&pt=-1', productstatusdescription: 'PRODUCTION DATA' }, url: "/document-viewer/cn//datasheet/GUID-XXXXXXXX-SF0T-XXXX-XXXX-000000202787.html", prepopulated: true, modalOptions: { dismissible: false } }); } open_reader(); | |