本资源的原文使用英文撰写。 为方便起见,TI 提供了译文;由于翻译过程中可能使用了自动化工具,TI 不保证译文的准确性。 为确认准确性,请务必访问 ti.com 参考最新的英文版本(控制文档)。
LMR14010A 是一款 PWM 直流/直流降压稳压器。该器件具有 4V 至 40V 的宽输入范围,适用于各种工业和汽车应用。1µA 的超低关断电流可延长电池寿命。工作频率固定在 0.7MHz,从而允许使用小型外部元件,同时能够更大程度地降低输出纹波电压。在内部实现了软启动和补偿电路,从而限制了外部组件的数量。
LMR14010A 经优化可提供高达 1A 的负载电流。该器件具有 0.765V 的标称反馈电压。
该器件内置多种保护特性,例如逐脉冲电流限制、热感应和应对功耗过大的热关断。LMR14010A 采用薄型 TSOT-6L 封装 (2.9mm × 1.6mm × 0.85mm)。
PIN | TYPE | DESCRIPTION | |
---|---|---|---|
NAME | NO. | ||
CB | 1 | I | SW FET gate bias voltage. Connect Cboot capacitor between CB and SW. |
FB | 3 | I | Feedback Pin. Set feedback voltage divider ratio with VOUT = VFB (1+(R1/R2)). |
GND | 2 | G | Ground connection. |
SHDN | 4 | I | Enable and disable input pin(high voltage tolerant). Internal pull-up current source. Pull below 1.25 V to disable. Float to enable. Adjust the input undervoltage lockout with two resistors. |
SW | 6 | O | Switch node. Connect to inductor, diode and Cboot capacitor. |
VIN | 5 | I | Power input voltage pin. Input for internal supply and drain node input for internal high-side MOSFET. |
MIN | MAX | UNIT | ||
---|---|---|---|---|
Input Voltages | VIN to GND | –0.3 | 45 | V |
SHDN to GND | –0.3 | 45 | V | |
FB to GND | –0.3 | 7 | V | |
CB to SW | –0.3 | 7 | V | |
Output Voltages | SW to GND | –1 | 45 | V |
SW to GND less than 30-ns transients | –2 | 45 | V | |
Operating junction temperature, TJ | –40 | 150 | °C | |
Storage temperature range, Tstg | –55 | 165 | °C |
VALUE | UNIT | |||
---|---|---|---|---|
V(ESD) | Electrostatic discharge | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) | ±1000 | V |
Charged-device model (CDM), per JEDEC specification JESD22-C101(2) | ±500 |
MIN | MAX | UNIT | ||
---|---|---|---|---|
Buck regulator | Vin | 4 | 40 | V |
CB | 46 | |||
CB to SW | 6 | |||
SW | –0.7 | 40 | ||
FB | 0 | 5 | ||
Control | SHDN | 0 | 40 | |
Temperature | Operating junction temperature, TJ | –40 | 125 | °C |