SN65DSI85-Q1 DSI 转 LVDS 桥接器 具有 一个双通道 MIPI D-PHY 接收器前端
配置,此配置中在每个通道上具有 4 条信道,每条信道的运行速率为 1Gbps,最大输入带宽为 8Gbps。该桥接器可解码 MIPI DSI 18bpp RGB666 和 24bpp RGB888 视频流,并将格式化视频数据流转换为 LVDS 输出(像素时钟范围为 25MHz 至 154MHz),从而提供一个双链路 LVDS、单链路 LVDS 或两个单链路 LVDS 接口(每个链路具有 4 个数据信道)。
SN65DSI85-Q1 器件非常适用于 60fps 的 WQXGA (2560 × 1600),以及等效 120fps(高达 24 bpp)的 WUXGA 3D 图形和全高清 (1920x1080) 分辨率。该器件实现了部分线路缓冲以适应 DSI 与 LVDS 接口间的数据流不匹配的情况。
SN65DSI85-Q1 器件采用小外形 10mm × 10mm HTQFP
(0.5mm 间距)封装,工作温度范围为 –40ºC 至 +105ºC。
器件编号 | 封装 | 封装尺寸(标称值) |
---|---|---|
SN65DSI85-Q1 | HTQFP (64) | 10.00mm x 10.00mm |
PIN | TYPE | DESCRIPTION | |
---|---|---|---|
NAME | NO. | ||
ADDR | 64 | I/O | Local I2C interface target address select. See Table 6. In normal operation this pin is an input. When the ADDR pin is programmed high, it must be tied to the same 1.8-V power rails where the SN65DSI85-Q1 VCC 1.8-V power rail is connected. |
A_Y0P | 46 | O | LVDS channel A, LVDS data output 0 |
A_Y0N | 47 | O | |
A_Y1P | 44 | O | LVDS channel A, LVDS data output 1 |
A_Y1N | 45 | O | |
A_Y2P | 41 | O | LVDS channel A, LVDS data output 2 |
A_Y2N | 42 | O | |
A_Y3P | 36 | O | LVDS channel A, LVDS data output 3. A_Y3P and A_Y3N must be left not connected (NC) for 18-bpp panels. |
A_Y3N | 37 | O | |
A_CLKP | 38 | O | LVDS channel A, LVDS clock output |
A_CLKN | 39 | O | |
B_Y0P | 61 | O | LVDS channel B, LVDS data output 0 |
B_Y0N | 62 | O | |
B_Y1P | 59 | O | LVDS channel B, LVDS data output 1 |
B_Y1N | 60 | O | |
B_Y2P | 56 | O | LVDS channel B, LVDS data output 2 |
B_Y2N | 57 | O | |
B_Y3P | 50 | O | LVDS channel B, LVDS data output 3. B_Y3P and B_Y3N must be left NC for 18-bpp panels. |
B_Y3N | 51 | O | |
B_CLKP | 53 | O | LVDS channel B, LVDS clock output |
B_CLKN | 54 | O | |
DA0P | 19 | I | MIPI D-PHY channel A, data lane 0; data rate up to 1 Gbps. |
DA0N | 20 | I | |
DA1P | 21 | I | MIPI D-PHY channel A, data lane 1; data rate up to 1 Gbps |
DA1N | 22 | I | |
DA2P | 27 | I | MIPI D-PHY channel A, data lane 2; data rate up to 1 Gbps. |
DA2N | 28 | I | |
DA3P | 29 | I | MIPI D-PHY channel A, data lane 3; data rate up to 1 Gbps. |
DA3N | 30 | I | |
DACP | 24 | I | MIPI D-PHY channel A, clock lane; data rate up to 1 Gbps. |
DACN | 25 | I | |
DB0P | 4 | I | MIPI D-PHY channel B, data lane 0; data rate up to 1 Gbps. |
DB0N | 5 | I | |
DB1P | 6 | I | MIPI D-PHY channel B, data lane 1; data rate up to 1 Gbps. |
DB1N | 7 | I | |
DB2P | 10 | I | MIPI D-PHY channel B, data lane 2; data rate up to 1 Gbps. |
DB2N | 11 | I | |
DB3P | 12 | I | MIPI D-PHY channel B, data lane 3; data rate up to 1 Gbps. |
DB3N | 13 | I | |
DBCP | 8 | I | MIPI D-PHY channel B, clock lane; operates up to 1 Gbps. |
DBCN | 9 | I | |
EN | 2 | I | Chip enable and reset. The device is reset (shutdown) when the EN pin is low. |
GND | 23 | G | Reference ground |
26 | G | ||
52 | G | ||
IRQ | 33 | O | Interrupt signal |
REFCLK | 17 | I | This pin is an optional external reference clock for the LVDS pixel clock. If an external reference clock is not used, this pin must be pulled to ground with an external resistor. The source of the reference clock must be placed as close as possible with a series resistor near the source to reduce EMI. |
RSVD1 | 34 | I/O | Reserved. This pin must be left unconnected for normal operation. |
RSVD2 | 1 | I | Reserved. This pin must be left unconnected for normal operation. |
SCL | 15 | I | Local I2C interface clock. |
SDA | 16 | I/O | Local I2C interface data |
VCC | 3 | — | 1.8-V power supply |
14 | — | ||
18 | — | ||
32 | — | ||
35 | — | ||
40 | — | ||
43 | — | ||
48 | — | ||
49 | — | ||
55 | — | ||
58 | — | ||
63 | — | ||
VCORE | 31 | P | 1.1-V output from the voltage regulator. This pin must have a 1-µF external capacitor to ground. |
PowerPAD | — | Reference ground |