ZHCSPG0 December   2021 TCAN1167-Q1

PRODUCTION DATA  

  1. 1 特性
  2. 2 应用
  3. 3 说明
  4. 4 Revision History
  5. 5 说明（续）
  6. 6 Pin Configurations and Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 ESD Ratings IEC Specification
    4. 7.4 Recomended Operating Conditions
    5. 7.5 Thermal Information
    6. 7.6 Power Supply Characteristics
    7. 7.7 Electrical Characteristics
    8. 7.8 Switching Characteristics
    9. 7.9 Typical Characteristics
  8. 8 Parameter Measurement Information
  9. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  VSUP Pin
      2. 9.3.2  VCCOUT Pin
      3. 9.3.3  Digital Inputs and Outputs
        1. 9.3.3.1 TXD Pin
        2. 9.3.3.2 RXD Pin
      4. 9.3.4  GND
      5. 9.3.5  INH Pin
      6. 9.3.6  WAKE Pin
      7. 9.3.7  nRST Pin
      8. 9.3.8  SDO
      9. 9.3.9  nCS Pin
      10. 9.3.10 SCLK
      11. 9.3.11 SDI
      12. 9.3.12 CAN Bus Pins
      13. 9.3.13 Local Faults
        1. 9.3.13.1 TXD Dominant Timeout (TXD DTO)
        2. 9.3.13.2 Thermal Shutdown (TSD)
        3. 9.3.13.3 Under/Over Voltage Lockout
        4. 9.3.13.4 Unpowered Devices
        5. 9.3.13.5 Floating Terminals
        6. 9.3.13.6 CAN Bus Short Circuit Current Limiting
        7. 9.3.13.7 Sleep Wake Error Timer
      14. 9.3.14 Watchdog
        1. 9.3.14.1 Watchdog Error Counter
        2. 9.3.14.2 Watchdog SPI Control Programming
        3. 9.3.14.3 Watchdog Timing
        4. 9.3.14.4 Question and Answer Watchdog
          1. 9.3.14.4.1 WD Question and Answer Basic information
          2. 9.3.14.4.2 Question and Answer Register and Settings
          3. 9.3.14.4.3 WD Question and Answer Value Generation
        5. 9.3.14.5 Question and Answer WD Example
          1. 9.3.14.5.1 Example configuration for desired behavior
          2. 9.3.14.5.2 Example of performing a question and answer sequence
      15. 9.3.15 Bus Fault Detection and Communication
    4. 9.4 Device Functional Modes
      1. 9.4.1 Operating Mode Description
        1. 9.4.1.1 Normal Mode
        2. 9.4.1.2 Silent Mode
        3. 9.4.1.3 Standby Mode
        4. 9.4.1.4 Sleep Mode
          1. 9.4.1.4.1 Remote Wake Request via Wake-Up Pattern (WUP)
          2. 9.4.1.4.2 Local Wake-Up (LWU) via WAKE Input Terminal
        5. 9.4.1.5 Reset Mode
        6. 9.4.1.6 Fail-safe Mode
      2. 9.4.2 CAN Transceiver
        1. 9.4.2.1 CAN Transceiver Operation
        2. 9.4.2.2 CAN Transceiver Modes
          1. 9.4.2.2.1 CAN Off Mode
          2. 9.4.2.2.2 CAN Autonomous: Inactive and Active
          3. 9.4.2.2.3 CAN Active
        3. 9.4.2.3 Driver and Receiver Function Tables
        4. 9.4.2.4 CAN Bus States
    5. 9.5 Programming
      1. 9.5.1 Serial Peripheral Interface (SPI) Communication
      2. 9.5.2 Serial Clock Input (SCLK)
      3. 9.5.3 Serial Data Input (SDI)
      4. 9.5.4 Serial Data Output (SDO)
      5. 9.5.5 Chip Select Not (nCS)
      6. 9.5.6 Registers
        1. 9.5.6.1  DEVICE_ID_y Register (Address = 0h + formula) [reset = xxh]
        2. 9.5.6.2  REV_ID_MAJOR Register (Address = 8h) [reset = 00h]
        3. 9.5.6.3  REV_ID_MINOR Register (Address = 9h) [reset = 00h]
        4. 9.5.6.4  SPI_RSVD_x Register (Address = Ah + formula) [reset = 00h]
        5. 9.5.6.5  Scratch_Pad_SPI Register (Address = Fh) [reset = 00h]
        6. 9.5.6.6  MODE_CNTRL Register (Address = 10h) [reset = 04h]
        7. 9.5.6.7  WD_CONFIG_1 Register (Address = 13h) [reset = 54h]
        8. 9.5.6.8  WD_CONFIG_2 Register (Address = 14h) [reset = 02h]
        9. 9.5.6.9  WD_INPUT_TRIG Register (Address = 15h) [reset = 00h]
        10. 9.5.6.10 WD_QA_CONFIG Register (Address = 2Dh) [reset = 0h]
        11. 9.5.6.11 WD_QA_ANSWER Register (Address = 2Eh) [reset = 0h]
        12. 9.5.6.12 WD_QA_QUESTION Register (Address = 2Fh) [reset = 0h]
        13. 9.5.6.13 STATUS (address = 40h) [reset = 00h]
        14. 9.5.6.14 INT_GLOBAL Register (Address = 50h) [reset = 0h]
        15. 9.5.6.15 INT_1 Register (Address = 51h) [reset = 0h]
        16. 9.5.6.16 INT_2 Register (Address = 52h) [reset = 40h]
        17. 9.5.6.17 INT_3 Register (Address 53h) [reset = 0h]
        18. 9.5.6.18 INT_CANBUS Register (Address = 54h) [reset = 0h]
        19. 9.5.6.19 INT_ENABLE_1 Register (Address = 56h) [reset = F3h]
        20. 9.5.6.20 INT_ENABLE_2 Register (Address = 57h) [reset = 3Fh]
        21. 9.5.6.21 INT_ENABLE_3 Register (Address =58h) [reset = 80h]
        22. 9.5.6.22 INT_ENABLE_CANBUS Register (Address = 59h) [reset = 7Fh]
        23. 9.5.6.23 INT_RSVD_y Register (Address = 5Ah + formula) [reset = 00h]
  10. 10Application Information Disclaimer
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
        1. 10.2.1.1 Bus Loading, Length and Number of Nodes
      2. 10.2.2 Detailed Design Procedures
        1. 10.2.2.1 CAN Termination
    3. 10.3 Application Curves
  11. 11Power Supply Requirements
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Documentation Support
      1. 13.1.1 Related Documentation
    2. 13.2 接收文档更新通知
    3. 13.3 支持资源
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 术语表
  14. 14Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.6 Power Supply Characteristics

Over recomended operating conditions with TJ = -40°C to 150°C, unless otherwise noted. All typical values are taken at 25°C, VSUP = 12 V, and RL = 60 Ω
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Supply Voltage and Current
ISUP Supply current
Bus biasing active: dominant		 TXD = 0 V, RL = 60 Ω, CL = open
See Figure 8-2		 60 mA
TXD = 0 V, RL = 50 Ω, CL = open
See Figure 8-2		 70 mA
Supply current
Bus biasing active: recessive
 		 TXD = VCCOUT, RL = 50 Ω, CL = open
See Figure 8-2		 3 mA
ISUP(STB) Supply current
Standby mode
Bus bias autonomous: inactive		 5.5 V < VSUP ≤ 19 V
See Figure 8-2		 230 µA
ISUP(SLP) Supply current
Sleep mode
Bus bias autonomous: inactive		 5.5 V < VSUP ≤ 19 V
TA > 85℃
See Figure 8-2		 50 µA
ISUP(SLP) Supply current
Sleep mode
Bus bias autonomous: inactive		 5.5 V < VSUP ≤ 19 V
TA ≤ 85℃
See Figure 8-2		 40 µA
ISUP(BIAS) Supply current
Bus bias autonomous: active(1)		 5.5 V < VSUP ≤ 28 V
See Figure 8-2		 60 µA
UVSUPR Under voltage VSUP threshold rising Ramp Up 4.05 4.42 V
UVSUPF Under voltage VSUP threshold falling Ramp Down 3.9 4.25 V
VCCOUT Characteristics
VCCOUT 5 V regulated output VSUP = 5.5 to 18 V
IL = 0 to 100 mA
TXD = VCCOUT		 4.9 5 5.1 V
VCCOUT 5 V regulated output VSUP = 5.65 to 18 V
IL = 0 to 100 mA
TXD = 0 V; VCANH = 0 V		 4.9 5 5.1 V
VCCOUT_DROP Dropout voltage 5 V LDO, VSUP – VCCOUT, IL = 125 mA 300 650 mV
∆VCCOUT(∆VSUP) Line regulation VSUP = 5.5 to 28 V, IL = 10 mA, ΔVCCOUT 50 mV
∆VCCOUT(∆VSUPL) Load regulation IL = 1 to 125 mA, VSUP = 14 V, ΔVCCOUT 50 mV
UVVCCOUTR Under voltage VCCOUT threshold rising Ramp Up 4.25 4.6 4.75 V
UVVCCOUTF Under voltage VCCOUT threshold falling Ramp Down 4.2 4.45 4.7 V
OVCCOUTR Over voltage VCCOUT threshold rising Ramp Up 5.7 6.15 V
OVCCOUTF Over voltage VCCOUT threshold falling Ramp Down 5.47 5.65 V
IL_VCCOUT Output current limit VCCOUT short to ground 175 275 mA
PSRRVCCOUT Power supply rejection ripple rejection VRIP = 0.5 VPP, Load = 10 mA, ƒ = 100 Hz, CO = 10 μF 60 dB
(1) After a valid wake-up the total ISUP current is the sum of ISUP(STB) and ISUP(BIAS) (ISUP = ISUP(STB) + ISUP(BIAS))